Having problems with your GE GLD4460NSS Stainless Steel Dishwasher ?

No lights displayed at all and the unit does not turn on. Tryed reseting the circuit breaker


Answers :

It doesn't work at all\015\012\015\012If your dishwasher doesn't work at all, check these:

Power from the house
Door switch
Wiring
Timer or selector switch
\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficult to test, because dishwashers are usually wired directly to an electrical circuit, rather than plugged into the wall. But at least check for a blown fuse or a tripped circuit breaker.

\015\012\015\012\015\012\015\012Door switch\015\012\015\012The door switch is important because, if it's defective, the dishwasher won't work at all. To reach it, you need to remove the control panel cover, or sometimes the interior liner of the door. If it's defective, you need to completely replace it.

\015\012\015\012\015\012\015\012Wiring\015\012\015\012Often the main wiring connection from the house, at the dishwasher, burns and breaks the connection. If that's the problem, the wires must be repaired/replaced as necessary. If that's not the problem, check the wiring to the door switch, the wiring between the door and the lower part of the dishwasher, and the wiring to the timer. Repair any broken, burned, brittle, or defective wiring, using the proper appliance-grade wire and connectors.

\015\012\015\012\015\012\015\012Timer or selector switch\015\012\015\012Although it's uncommon, the timer or the selector switch may be defective. If so, you need to replace the defective part, because neither of these can be repaired.
Repair Help & Product Troubleshooting for GE GLD4460NSS Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No lights displayed at all and the unit does not turn on. Tryed reseting the circuit breaker


It doesn't work at all\015\012\015\012If your dishwasher doesn't work at all, check these:Power from the house ... GE GLD4460NSS Stainless Steel Dishwasher

We have a KitchenAid KEBC147KSDS06 24" conv. oven. After putting it through a clean cycle, I tried to preheat it to conv, bake @ 350 deg. The display comes up normally and the fan runs, but after 5 sec. the temp disappears from the display and 'Lo' appears in its place. The conv. fan continues to run but neither upper nor lower element heats. Following a suggestion, I tried to reset the oven by turning off its circuit breaker and powering back up, but it did not correct the problem.


It depends how long you had the self-clean function running. The oven is known to overheat and damage the thermostat during self-clean.\015\012\015\012See postings on some user forums.\015\012\015\012 ... KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

Kitchen circut was accidently turned off. Now whirlpool gold disher will not work(unit was not running and the door was not closed all the way when circuit was turned off, All circuit breakers are on) There are no lights on display when door is closed completely, and it appears to have no power. Worked fine prior, what could it be? The unit has not been removed from under the counter yet. Is there a fuse or circuit breaker on the unit? If so where is it located? Other troubleshooting ideas


Hello- Turn power off. Remove kick panel and cover for power wires. Check connections. If these are ok, most likely suspect is a fuse at the control. This is a little harder to get to. Remove inside door panel screws. Unplug wires and remove panel. F ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Have a Maytag dishwasher that will not run, display panel just has three blinking lights. Have turned off circuit breaker trying to reset dishwasher, to no avail. Still blinking.


Behind the lights and the control buttons there is a central control circuit board (known as the CCU), this board is going to need to be replaced, the part price depends on the model number of the dish washer, but on a ... Maytag Dishwashers

Kenmore Ultra Wash Model 665.15801891 (Serial FJ3403697). This is in the USA. Unit will not run. Two lights are lit on the display panel and do not go off - 'Drying' and the #2 on 'Delay Hours'.rn I have turned off the power at the breaker box hoping it would reset. Once power is turned back on the Lock light comes on. I can clear that by pressing 'No Heat Dry' for 4 seconds but then the 2 lights mentioned above come on and do not go off. Any suggestions? Can you tell how old the unit is by t


Plase confirm if your model has the same front panel as the one shown in this manual.\015\012In that case try this sequence to reset the dis ... Kenmore 15899 Built-in Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

We had a power failure so the unit was flashing a PF error message. I turned the circuit breaker on and off and the thing just stopped- no more flashing lights...no there there. Is there a reset function and where would that be? Or is it truly dead? I have also been looking for two days for a replacement. As an expert, do you have information on reliability on newer models? The best rated I've researched even through CR are both loved and hated by consumers. Traditionally, repairmen ha


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. Now th ... Frigidaire Dishwashers

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

I have a KitchenAid KUDp02FRSS1 dishwasher and it will not respond to any buttons being pushed. The Normal, Light China and Cancel lights continue to blink. I have tried reseting the circuit breaker to power cycle the machine but when I turn the power back on it just continues to blink.


... Dishwashers

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

Bosch Dishwasher The label is damaged, but it looks like I have M/N: SHV4303UC Bosch dishwasher. I need to reset (reboot) the electronics. It is stuck in the opening cycle of draining excess water. I've tried turning of the circuit breaker for a long time (10 hours overnight) and that did not work. How can I correct this?


The reason it is doing this is because the anti flood valve is either stuck or you have a leak in the bottom of the dishwasher. if you tip it back slightly does water come out? if so you have a leak, If not take the front panel of and you will see a ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

Kitchenaid dishwasher KUDC10IX does not start, no lights come on. Turning circuit breaker off then on no longer resets it.


... Dishwashers

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

Bosch SHE4AM16UC/05 dishwasher will not operate, lights for "Clean" and "Autowash" remain on. Can turn on and off, but that's it. Tried reset, turning it on and off from the breaker, checking dr


... Bosch Ascenta SHE4AM16UC Full Console Dishwasher - Black

I have a GE gss1800z02. When the unit is turned on it starts to work, then sparks start coming out of the bottom of the unit. If the unit is off and the circuit breaker is on, their is a sound similar to a TV being turned on about every 30 seconds.


... GE Dishwashers

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I have a GE QuietPower2 (Model GLD5800L00BB) and the lights are blinking and there is a beep about once every 60-90 seconds or so. I have reset the circuit breaker but when I turn it back on, same issue. I can't reset or turn on.


This model has a known problem with the door switches. There are two switches and they both need to work right, otherwise the panel switches will not work right. Turn off power before working on the switches. They both have to open circuit when the d ... General Electric Adora GHDA670N Built-in Dishwasher

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Frigidare dishwasher model gld355rfb2 when you select a wash cycle unit begins prewash when it moves to wash unit quits and pf (power failure )is on display unit is full of water on bottom of unit so I reset the unit hit cancel button at which time unit pumps off water . I then tried again with same results as above.


... General Electric GDWT160RSS 24 in Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1354 seconds