Having problems with your GE GSD5130 Dishwasher ?

I replaced the control board. The old one had no lights and would not do anything. I pluged the new in and the clean light just flashes. I can't get it to do anything.


Answers :

Repair Help & Product Troubleshooting for GE GSD5130 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I replaced the control board. The old one had no lights and would not do anything. I pluged the new in and the clean light just flashes. I can't get it to do anything.


... GE GSD5130 Dishwasher

Clean light keeps flashing, cant get it to reset. What can I do?


Hi, if the clean light flashes it is indicating the was no rise in water temperature during the water heating cycle. This link below will explain things that could cause it and tell you how to reset the control so you can wash for now. Let me know if ... Kenmore 24 in. 17022 Built-in Dishwasher

Clean light flashes constanly. Won't clear out to start new cycle


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a G863scvi intake drain light is flashing unable to retrieve a repair manual it seems we cant get one? Any way screens are clean Im about to pull this unit out does no good if your unable to fi


... Miele 24 in. Incognito G863 SCVi Built-In Dishwasher

Kitchenaid KUDS01FL -Dishwasher - "clean" light wont stop flashing; cant start a new load


Hi,\015\012\015\012\015\012The clean light usually will blink due to a failure to heat the water properly. This dishwasher looks for a temperature rise of the water during a heating cycle if it fails to see this rise for multiple cycles i ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

We have a Zanussi ZIDW 956 built in dishwasher. Problem is hat it gets a short way into the program and then stops and then a light at the top is flashing ''A''. Cant see any blockage. Machine is regularly cleaned. Can you help Ben


Hi\015\012 \015\012If you have checked the drain hose and there is no blockage, and assuming that you have also checked the water inlet valve for any blockages. The issue can be with the door switch that is bad or the c ... Dishwashers

Clean light flashes cant get to start a wash cycle


If the clean light flashes 7 times, pauses, then repeats...\015\012\015\012When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012 ... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher

I have a Kenmore Elite dishwasher and the green light on clean just flashes. I can't get the dishwasher to do anything.


Try turning the control knob all the way around a couple times. It worked on mine. ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

I have a GE quietpower 3 and I cant get the door to shut. There is a green light on that says clean. There are no dishes or anything in the way of the door. I have no idea what is going on and I really do not want to phone my landlord. Please help!


The door latch is probably in the shut position. you need to move it to the open postion. ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a stock #17039 model #665.17039400 Kenmore dishwasher. It wont cycle & cannot get past the clean light flashing.


... Kenmore 24 in. 17039 Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work


... Frigidaire Dishwashers

Diswasher malfunction - won't start clean light flashes 7 times The clean light keeps flashing green. Can't get the washer to start. The only operation it will do, is drain when the cancel / Drain button is pushed This unit is: Stock # 16029 Type # 575-0 Model # 665.16029.402


This information may help in your situation. This can be a common problem on some Whirlpool manufactured dishwashers. The following link explains how you may be able to clear the blinking clean light problem: ... Kenmore 24 in. 16029 Built-in Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Whirlpool dishwasher Clean light is flashing, we just bought it last week and after the third wash, the Clean light started flashing and it won't go off, which stops it from doing anything else. User manul says to have it serviced, but that seems unneccessary. It doesn't seem to be draining completely, so there may be a knk in the pipe, which may be related, just not sure


The blinking clean light is an interruption in the dishwasher program that either indicates a malfunction, or a simple program glitch. The following link explains how you may be able to clear the blinking clean light problem: ... Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

Clean light flashes constanly. Won't clear out to start new cycle


I can't get the light to clear off. I can "cancel" and it goes through\015\012the drain cycle, but when done after opening the door to reload, then\015\012trying to start, it does nothing. ... Whirlpool GU2400XTP Built-in Dishwasher

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


... Dishwashers

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


You will have to reset the dishwasher. First try and turn off the mains power and back on after a short time. If the clean light flashing starts again then you go through the hard reset procedure. press NORMAL WASH then HEATED DRY buttons on ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1821 seconds