Having problems with your GE GSD5130 Dishwasher ?

G.E. GSD5130 When the dishwasher is pumping out the water a small amount comes in the rotating sprayer head. At the end of the cycle the dishwasher still has water in the bottom. The amount of water varies from just a little to over an inch. I replaced the spring loaded check valve a couple of months earlier and everything worked fine until now. What should I check? Thankyou.


Answers :

Mike, I just ran into the same problem. I found a second check valve located in the outlet hose of the ELECTRIC drain motor. This motor is located at the right rear underside of d/w and is used only for backflush of the filter. When the unit goes thru a normal drain cycle, this chk valve closes to prevent backflow to lower sump area thereby increasing the pump pressure to the "piston/nut asmy" popping that up to seal that chamber which then forces water to go up to drain.
\015\012You've probably fixed or replaced the thing by now but this might help others.
Repair Help & Product Troubleshooting for GE GSD5130 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

G.E. GSD5130 When the dishwasher is pumping out the water a small amount comes in the rotating sprayer head. At the end of the cycle the dishwasher still has water in the bottom. The amount of water varies from just a little to over an inch. I replaced the spring loaded check valve a couple of months earlier and everything worked fine until now. What should I check? Thankyou.


Mike, I just ran into the same problem. I found a second check valve located in the outlet hose of the ELECTRIC drain motor. This motor is located at the right rear underside of d/w and is used only for backflush of the filter. When the unit goes th ... GE GSD5130 Dishwasher

Model FDB4315LFC2 Serial TH80658596 It is only 20 months old but Does not load with water. I have checked water line into white valve and water is flowing, but it does not come into the dishwasher. If I manually put water in the bottom of the dishwasher it works fine through the cycle until it is time to pump in more water. There is a sound but no water comes through the valve.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. As you have already checked the water line for clogs/obstructions and the water is flowing but wont fill ... Frigidaire Dishwashers

I have a triton XL model GSD6900 that does not fill with water. I replaced the fill valve about 8 months ago. Have checked the inlet valve and coil shows continuity. Ran it thru a cycle and found no voltage at the valve. I assume the problem is in the timer. If this is the case should I have it repaired or buy a new dishwasher.


... GE 24 in. GSD6900J Built-in Dishwasher

The dishwasher won't fill with water. We took the water inlet valve off and cleaned the filter screen. The dishwasher worked about 2 times and started doing the same thing. We then replaced the water inlet valve and again, the dishwasher worked a couple of times and now we're back to it not filling again. What could the problem be?


Check the float assembly, that will trip and stop water from coming in. May have soap or grime holding it up. ... GE 24 in. GLD6260LSS Stainless Steel Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

Hotpoint hda3440g02sa leaves a little water at the bottom of the dishwasher I have checked the check valve have even replaced I have put a high loop in the drain hose and still no help it leaves just a little water I hate to put a new pump because I have on this type of dishwasher before and still no help


Hi\015\012\015\012 \015\012\015\012When the dishwasher leaves just a little water and drains\015\012maximum then I would say that it is fine & the drain pump is also working\015\012fine. These units are designed in such a way tha ... Dishwashers

I have a Kenmore 363.15655891 Dishwasher. It will not fill with water. I have replaced the fill valve, water is on to the machine. When I check the electric connection for the fill valve it does no


... Dishwashers

Frigidaire Dishwasher FDB740RC. Not cleaning dishes well. Just in the past couple weeks. When the dishwasher fills with water, how full should it get. When mine fills, it definitely doesn't go up to the element, and just barely makes it to the float switch (not enough to trigger it), makes it to just below the base of it, doesn't come up the side of it at all. Is this normal, or should there be more water. The Water valve has been replaced already.


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Frigidaire 24 in. FDB740RC Energy Star® Built-in Dishwasher

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

Frigidaire built in dishwasher model PLD2855RFC1. Have to wash dishes pretty much spotless prior to using dishwaser. Glasses come out with what appears to be soap residue regardless if powder or liquid. Did not use a gauge but water pressure in rest of house is good, recently replaced water heater, pressure regulator and just replaced the dish washer water source valve. Washer is about 18 months old, has never worked really well.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Frigidaire PLD2855RFC Dishwasher

I stopped using my dishwaser because it left crusted on food particals even tho I rinced them well(so I thought) before loading. It was as if they were just being dried crusty. After a couple month I noticed a bad smell. I looked in the dishwasher to find standing water in the bottom. I ran a little CLR through and it cleared out. But a couple weeks later again there was water in the bottom. It seems as if the water from the sink is draining into the washer. If I run it it runs thru just fine, n


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Estate 24 in. TUD4700KQ / TUD4700KB Built-in Dishwasher

I have a Miele Dishwasher 2430 Sci. It's been not used for 5 months and when I returned it worked fine for several times (at least 6). NOW the intake/drain light keeps blinking. I have already cleaned out the drain and replaced it properly (there was nothing in there and it was clean). No water is coming into the dishwasher?however I know that the water hook-up is on (the first thing I checked). I turned the water on and off several times and AM SURE it's on now. What else could be


The usual course of events is to check and clean the filter, check and clean the water pump and well, check and clean the waste pipe and any connection to a sink or waste disposal system, then check the inlet warer pressure, then the machine level / ... Miele G2430SCi Dishwasher

I had a problem with my dishwasher popping the breaker. I opened the bottom and found burnt up wires. I fixed those and now the dishwasher stays on and begins its cycle (by draining) but the water is not flowing to the machine. It has supply, and I just now replaced the water inlet valve- no difference. The water was working before the breaker issue. I'm wondering if it is now something as simple as a clog somewhere since the washer sat unused for a month; or, if it is something more compli


I read your previous problem. This appears to be separate problems. The first was likely a loose wire. When a wire has a loose connection they build heat and can melt. The current issue would seem like the float switch is stuck. The float switch is ... Bosch SHU9925UC Built-in Dishwasher

Our KitchenAid KUDS011JBS1 dishwasher sometimes leaks water on our kitchen floor. It seems to drip from the bottom edge of the door onto the floor. It's not a huge amount of water, but is enough to be a concern... it leaves a small puddle on the floor. What should I check and how do I fix this? I'm hoping it's an inexpensive and easy fix. Note that we've had this dishwasher for 8 years and have only noticed leaking during the past 6 months.


... Dishwashers

Water leak have the Ge triton dishwasher (Model # GSD5320D02BB, bought it n 2001) and currently have very small amount of water leaking out of the door during a run cycle. I did check levels when running and that seems to be fine......meaning the dishwasher is level and not an over-flow problem. My next thought is maybe it is a faulty door gasket. So my question is, where is the door gasket located and how do I replace it? (and where do I order this part from?). Looked for diagrams to follow and


They are in the bottom left and right of the door opening. GE likes to use L-shaped, molded and ribbed seals on most of their models - hopefully also on yours. Typically these can be removed by hand and easily replaced without taking anything apart. ... GE Tritonr XL GSD6260JCC Dishwasher

Our 2 month old Frigidaire FGHD2433KF1 dishwasher is producing a very strong foul odor. It is not connected to a garbage disposal and we only see a small amount of water in the bottom of tub when the dishwasher is off. When I use the sanitize cycle, it seems that the smell is even more intense, not sure if that could be do to a small amount of steam escaping on the highest setting ? We have no idea what to check any suggestions would be much appreciated


Do you have it connected to an air gap? If not this can allow the water to drain back into the dishwasher and will sometimes have food particles in it making it stink. ... Dishwashers

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

KUDS30 leaking my kitchenaid dishwasher (about 1 1/2 years old) had a leak bottom left side and had gasket replaced. It worked well for approx another 6-9 months without any leaks and now the same problem is back. The dishwasher isn't overloaded. A repair person came last week and ran the dishwasher empty and it didn't leak when she was here. The 2 loads after continue to leak approx 2 cups of water each cycle.


... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Have a hotpoint dishwasher, replaced the water valve and it doesn't seem to loading water. I disconnected both sides of the water line but still is not working. Any ideas?


THERE IS A FLOAT/FLOOD SWITCH ON THE FRONT LEFT SIDE INSIDE THE TUB. SOMETHING MAY HAVE GOTTEN UNDER IT OR IT IS GUNKED UP. THIS WILL PREVENT VOLTAGE FROM GOING TO THE WATER VALVE, THUS, NO WATER. ... Dishwashers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

I have a GLD 4456R00CS dishwasher that is maybe 6 months old. It seems to cycle properly, but has never really cleaned the dishes. This is the worst dishwasher we've ever had (over 25 years) and I'm ready to take it to the street. I've cleaned the screen (was already clean), checked the spray bars for clogs (removed, sprayed water through it, and replaced), and looked for any other obvious problem.


Sorry you have had so much problems with this dishwasher. Before you "take it to the street" please check one more thing. I have had so many people say similar problems. \012\012\012\012Check that you are usin ... GE GLD4456RCS Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2928 seconds