Having problems with your GE Monogram® ZBD6880NSS Stainless Steel Dishwasher ?

Have GE Monogram ZBD6880 dishwasher. Ran unit and unloaded. Went to use the next day, and none of the buttons to select and start will work- it is as if the unit has no power. I confirmed that there is power to the unit. Is there a way to reset, seems like it might be something simple.


Answers :

Repair Help & Product Troubleshooting for GE Monogram® ZBD6880NSS Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have GE Monogram ZBD6880 dishwasher. Ran unit and unloaded. Went to use the next day, and none of the buttons to select and start will work- it is as if the unit has no power. I confirmed that there is power to the unit. Is there a way to reset, seems like it might be something simple.


... GE Monogram® ZBD6880NSS Stainless Steel Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Our dishwasher seems to have stopped working over night. The power button comes on and the unit beeps to acknowledge start, but then there is only a very light hum & the unit does not start. No water comes through the unit and it just hangs at the light hum. We have not turned off any water but just checking if there is a simple solution? Adam Hdw100sst


Suspect pump.on start the pump will activate to remove condense water from drying the last load.if the pump does not start then the next step of adding water to start wash cycle will not happen.ensure pump is not blocked ... Dishwashers

AEG Favorit - model F86050UM The dishwasher was disconnected and moved whilst new timber flooring was being laid. On reconnection it was evident there was some water in the base of the unit, this was removed by tipping the unit over to drain. Now there is no power display on the door.Power outlet checked OK. Your assistance would be appreciated in this seemingly simple problem. Murray


What has happened is that you have tripped the overflow/anti flood device switch when you upended the machine. You most likely need to empty out the salt container, and to reset the antiflood give the machine a few sideways tips and try to shake fre ... AEG Dishwashers

Hi I have a whirlpool diswasher which is about 7 uears old which has blown the fuse (and the mains trip) half way through a cycle. Replaceing the fuse has resulted not resulted in the restoring of power to the unit. Is there anything simple I could check (in line fuses etc.)? Cheers


Some whirlpool models do have a thermal fuse in the consloe mounted to the main control board housing, might looke to see if it has one and if it is good ... Dishwashers

I have a blanco dishwasher BFDWC65, when I put the cycle on it seems to be struck one one cycle, is there a way to reset the unit or is there something wrong with the electronics


I have the same problem and am interested if you solved this? ... Dishwashers

I have a maytag dishwasher model MDB8600AWQ that suddenly stoped working, no power lights on panel. I have had multiple problems with this unit with a complete service approxinamtely 1 year ago and had no problems until there just seems like there is no power to the unit. It is used infrequently and has been wwll maintained. Is there an easy solution or should I just give up on this unit.


Please refer to the diagrams on this site. \015\012\015\012If the ... Maytag Dishwashers

My SHV6803UC/15 seems to be cycling properly, but it's not cleaning the way it used to. I noticed a lot of soap residue all over the glasses, dishes and wall and base areas. We do have hard water, but have never seen this 6yr old unit act this way, are there any tips you can offer before calling in a repairman or replacing the unit. Advice welcome, --Phil


Ther is a hose which goes from the left hand side water chamber to the sump, this hose gets blocked and not enough water fills into the machine. Remove the left hand side panel of the dishwasher to access the chamber and hose, remove, clean & ref ... Bosch SHV68 Built-in Dishwasher

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.


It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

Kitchen circut was accidently turned off. Now whirlpool gold disher will not work(unit was not running and the door was not closed all the way when circuit was turned off, All circuit breakers are on) There are no lights on display when door is closed completely, and it appears to have no power. Worked fine prior, what could it be? The unit has not been removed from under the counter yet. Is there a fuse or circuit breaker on the unit? If so where is it located? Other troubleshooting ideas


Hello- Turn power off. Remove kick panel and cover for power wires. Check connections. If these are ok, most likely suspect is a fuse at the control. This is a little harder to get to. Remove inside door panel screws. Unplug wires and remove panel. F ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Bottom unit does not always seal and causes water to collect in bottom pan which throw unit into f1 status. Sometimes it stays sealed and is difficult to pull drawer out. Is there a way to reset the unit properly? I know how to pull the drawer and fix the f1 problem but it seem like the seal issue is becoming more frequent. Thanks


These dishwashers are very sensitive to grime collecting around the drawer edges. Try cleaning with a damp cloth by rubbing along the top edges and the sides where the drawer door sits flush with the body.\015\012\015\012Also trun off pow ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch dishwasher (SXH55MO6UC/46): The power comes on and runs normal, but no water is coming into the unit. I was told that it was a water inlet valve that needs to be replaced (part #263833). I need to know if this is what needs to be replaced and if so, is this something that I can do or do I need an expert repair service to do it? If it is something that I can do, I need instructions. I am handy, but this is something that I have not done before, Thank you, Craig Covey


Hi Craig,Yes it may be the fill valve...but first take off the pipe or hose and check the screen just inside the fill valve...some do not have it but most do...also check that water comes out of the hose or pipe at the valve....THEN ... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

The Fisher Peykel dual drawer dishwasher : the top unit LED is off and the setting for length of wash is not lit up and is not functioning. There is power to unit because when I hit the lock button it beeps. Also the red light for the glass cleaning liquid compartment is lit. What seems to be the solution? I am an ME and hands on type, please advise.


Can you see a small lock inside the display panel??? the control may be locked. another issue might be a broken heater plate, not a very home owner freindly part to change( heater plate has a fuse inline that would kill power to function ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Draper Power Wash 2121. Worked ok yesterday. Today just seems to be power to the unit when switched on with a bit of a hum -but with little pressure nor the normal loud working noise. Suggestions welcome. Many thanks.


... Pressure Washers

The electronic panel on the top of the door doesnt light up anymore and is unresponsive, when the power is turned on, the machine makes a sound like its running or draining or something, but nothing is happening. This all started after a potential electrical disruption following a power outage. Perhaps there is a fuse or some relatively easy way to fix this? or am I screwed and should just call a repair man. Thanks for your suggestions, Brodie


... Bosch 24 in. SHX56B05 Stainless Steel Built-in Dishwasher

Water supply to my Bosch SHE43CO5UC/17 dishwasher seems interrupted and not being supplied to the unit. Water supply to the unit is checked and confirmed available. What are the possible causes, i.e. stuck solenoid valve?


Could be a dirty hose filter or faulty inlet valve. Ther could be a leak and the bottom of the unit has flooded activating the flood safety which will cut the water supply. The pressure chamber and/or the hose pressure chamber to sumo could be bloc ... Bosch Dishwashers

I have a D3100 that continues to pump out. None of the controls seem to do anything, the only way i could get it to stop was to turn of the power point.It does not reset as when i turned on the power point again it started pumping again.


The flood switch has turned on at the base. This means either the switch is faulty or water has leaked into the base of the housing. ... Asko Dishwashers

Seems my drain is plugged on my dishwasher it is the magic chef 4500b unit and i now have water all over my kitchen floor. i cant seem to find the product du4500b  so i entered the du2000 , either way there is water on my floor and about 4 inches of water in the bottom of the dishwasher


Ok there are several problems this can be caused from...1. there is usually a float device (I'm not sure about this model) that floats up and turns the water flow off when an appropriate amount of water is injected into the DW...sometimes these ... Magic Chef 24 in. DU2000 Built-in Dishwasher

We lost power as our dishwasher was running. When power was restored it seems to be stuck in the drain cycle. We have tried turning the unit off and back on and also holding the start button for 5 seconds.The 4 lefthand lights blink on and off and the right hand lights are steady. It is a model D1996.


Try to unplug it or turn off the circuit at the electric box.............wait ten minutes or so and plug it in and try again..................the program needs to be reset in that manner sometimes....... ... Dishwashers

No Power Hi. My dishwasher wont start. I loaded it and cannot get any lights to light up on it. There is no power to it at all it seems. I tried flipping the breaker but there is still nothing. The door locks, so that shouldnt be the issue. Is there a way to reset the machine? What should I do?


I have the exact same problem with my Kenmore Type 575-0. It was working one daym it went into dry storage for a year and then when I took it out of storage it would not work. Ive already tested the thermal fuse and there is nothing wrong with that. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Dishwasher does not seem to have power. I have a Kitchen Aid, under counter unit, 9 years old, model KUDS01I. I used it 2 nights ago with no problem. When I push a button, nothing happens, no lights show, etc. It is plugged into the lower half of a duplex socket with disposal plugged into the top. Disposal works, so the problem seems to be with the dishwasher. That also eliminates any issues related to breakers or ground fault indicators, etc. Is there a reset button on the dishwasher? Is there


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0847 seconds