Having problems with your GE Nautilus 24" Built-in Dishwasher ?

Won't Start Cycle, but will put water in bottom of dishwasher

\015 Turn knob to start sounds like it wants to start, but doesn't do anything. If you turn it a little more the water will pour into the bottom of the dishwasher. Now we have water in the bottom of the dishwasher.\015

Answers :

Model # should be on inside of tub wall....but any way...

This is a typical GE problem which I have seen many times...When a DW\015\012sets for a while not being used...the motor often freezes up....Take\015\012the front (lower panel off....find the motor assembly...(with the DW\015\012unplugged!!...very important)reach in with you hand or a screw\015\012driver...preferably your hand...at the back of the motor...there should\015\012be a impeller blade...you should be able to reach in with a finger and\015\012pull it down..it may be resistant so find a way to hold it in place as\015\012you reach up to the next impeller blade and pull down further...finally\015\012it will all of a sudden free up....after which you plug it back in and\015\012start it up...I am also including a step by step (no drain problem\015\012check list as you may run into an issue like this if it has not been\015\012operated for a while ....notice article # 5).


1. Air gap / Drain hoses
\015\012If there is an air gap (located in the sink, near the faucet), check to\015\012see if it is clogged. Unscrew the top cap and see if there is anything\015\012blocking inside. Note: If there is no air gap installed, the dishwasher\015\012might not drain properly.
\015\012\011\011\011
\015\012If the drain hose is clogged, the dishwasher would not drain. If there\015\012is an air gap installed, it is very common that a hose going from the\015\012air gap into the garbage disposer is clogged. Remove and clean the\015\012hose. Make sure to reattach the hose before starting the dishwasher.
\015\012\011\011\011
\015\012\011\011\011Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.
\015\012\011\011\011
\015\012\011\011\0112. Broken belt
\015\012\011\011\011Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.
\015\012\011\011\011
\015\012Note: Sometimes the belt would just come off the pump. Even though it\015\012might not be broken, it is recommended that you replace the belt,\015\012because it is probably too stretched out.
\015\012\011\011\011
\015\012\011\011\0113. Pump
\015\012Some models have two impellers inside the pump - one, wash impeller,\015\012takes care of the wash cycles, the other, drain impeller, drains the\015\012water out. If the drain impeller is broken (broken blades, shaft), the\015\012dishwasher would not drain. Replace any broken pump components.
\015\012\011\011\011
\015\012\011\011\0114. Drain solenoid
\015\012Some models (for example most GE dishwashers) use a drain solenoid to\015\012drain water out. Sometimes the solenoid gets stuck, preventing the\015\012water from draining out. Try to free up the solenoid. If unsuccessful,\015\012you might have to replace the pump assembly.
\015\012\011\011\011
\015\012\011\011\0115. Motor
\015\012\011\011\011If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.
\015\012\011\011\011
\015\012\011\011\011Replace the motor if defective.
\015\012\011\011\011
\015\012\011\011\0116. Timer
\015\012\011\011\011Replace if defective (note: uncommon problem).\015\012\011\015\012 \015\012\011

I hope this helps...it is always useful to include the Model #...more specific instructions can then be provided

Good Luck and good day.....please rate my effort...the Fang
Repair Help & Product Troubleshooting for GE Nautilus 24" Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

I have a baumatic mini4 tabletop dishwasher and when i put it on to start a cycle after 2 mins water starts pouring out the bottom of the door and floods my kitchen? i have checked pipes and they are ok and when i switch the dishwasher off and back on again the water drains out the bottom of the dishwasher ok.


Hi,\015\012\015\012As there are a couple of troubleshooting for this leak. As with out doing it is not easy to understand whether its a plumbing issue or the washer is not draining constantly in cycles.\015\012\015\012 ... Baumatic 18 in. BFD46 Free-standing Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

The start button is flashing on the dishwasher and it wont start,i try changing the different cycles but it just wont start,the bottom of the dishwasher was full of water in which i drained it and took out some type of filter as i thought it may be causing a blockage which it wasnt as i still have the same problem....please help...my name is adam


What type of dishwasher do you own? Model, Brand?It could be a touch pad or control board issue. ... Whirlpool Dishwashers

Neff dishwasher our dishwasher is six years old and have had no problems till now . there is power to it but when you push the on button the impeller starts up even when the door is open , and it wont go through the cycle , its asif there is no water going in and it is not draining away i have checked and cleaned the filters but nothing, then pulled it out from undre the sink and it started working . i put it back , it went through the cycle then the next day it would'nt work again . do i need a


You have a faulty door switch. It can be replaced and may be available at youre local appliance parts dealer. ... Dishwashers

My top dishdrawer stopped working half fill of water. I put it on rinse cycle and it drained the water. I found a bit of sand in the bottom of drawer. I wiped the sand out and then put onto a cycle. After a couple of minutes the dishwasher started flashing a tap symbol with a slash through it and stopped working. Any help please:) Jacki


... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Leaks my dishwasher was working great .. and then it started to leak at the bottom of the door when it would cycle into the wash mode .. I cleaned out the bottom trap and put the unit back . and now it will not cycle at all .. and there is water in the bottom of the as if it is not draining .. any ideas


Hello Emmitt White - Try unplugging the dishwasher or flipping the household circuit breaker off first. Wait approximately ten minutes and turn the unit back on. If the issue persists, it could possibly be a few things: faulty door switch, drain p ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Won't Start Cycle, but will put water in bottom of dishwasher


Model # should be on inside of tub wall....but any way...This is a typical GE problem which I have seen many times...When a DW\015\012sets for a while not being used...the motor often freezes up....Take\015\012the front (lower panel off.. ... GE Nautilus 24" Built-in Dishwasher

DISHWASHER WONT GO INTO WASH CYCLES,WHEN I PUSH START GOES CANCEL/DRAIN,CAN HERE PUMP RUNNING THEN IT WILL TURN OFF,THERE IS NO WATER IN THE BOTTOM,SEEMS LIKE STUCK IN DRAIN CYCLE


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

I have a Proline DWI 5212p dishwasher about 2 years old. Every time I turn it on it starts beeping and the first three lights start flashing. It is draining because if I put water in the bottom it goes when I turn it on but it won't start the wash cycle.


... Dishwashers

We put in a new garbage disposal and now our dishwasher wont workit starts each cycle we suggest, but the water does not run and the cycle does not move forward


Hi, \015\012\015\012Does the drain hose for your dishwasher connect to the disposer ? If so, has the knock out for the drain tube in the disposer been "knocked out" ?\015\012\015\012Check that and reply. We'll move forward from there if need be.\015\ ... Bosch 24 in. SHU43 Built-in Dishwasher

My electrolux dishwasher will not switch on - i put it on last night and the cycle was fine, come to empty it this morning and there is water in the bottom and it wont switch on on any of the cycles


... Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

WATER DOES NOT COMPLETELY DRAIN FROM DISHWASHER. TOOK APART DRIN VALVE OTHER NIGHT AND PUT BACK TOGETHER AND IT STARTED WORKING FOR ABOUT 5 LOADS. NOW THERE IS ABOUT 1/2 INCH WATER STANDING IN BOTTOM THAT IS NOT NORMALLY THERE AT THE END OF THE CYCLES.


It is likely that the water pump is feeling its age. Replace the pump. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Not draining we have a ge quiet power dishwasher it started not draining fully, I took the hose off under the sink and seemed to be lots of water running when i put it on rinse cycle but when I opened it up still water in bottom just wondering what it could be?


Are you sure your drain system is not clogged or restricting water flow ? When you say youtook off the hose off under the sink and it seemed to be lots of water running on the rise cycle .. that suggests that you may have a restriction af ... Dishwashers

Dishwasher is making a loud grinding noise when it's started. Doesn't matter the cycle choice; the cycle starts as normal then once started up starts making a sort of grinding noise as the water is pulsing, like something is stuck or blocking the "push" of water. I couldn't see anything stuck in the bottom - any thoughts before I call a repair person? I've never owned a dishwasher before - maybe there's a basic drain/blockage thing I should check out first? And, any recommendations for repair


... Maytag 24 in. MDBH970AW Built-in Dishwasher

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

My Bosch dishwasher is Exxcel 5 prg model no SMS50E020GB. When you first open the dishwasher door after the washing cycle finishes there is no water in the bottom of the dishwasher but about 45 minutes later water slowly appears in the bottom of the dishwasher. I scoup out the water and there is about 3 litres. The machine is just over 2 years old. I had a plumber check the machine and he couldn't find anything wrong with the machine. Another plumber came out and put on the invoice: "disma


... Bosch Dishwashers

Frigidaire Dishwasher This is my second dishwasher in 18 months. Water leaks out the bottom of the dishwasher. It did it on my first one now it''s doing the same thing.Could it be the water pressure from the city water line? How could this happen to two dishwashers in a row? The leak starts immediately when the wash cycle starts.


This is a simple solution, the brass nut that connects the heating element to the base of the dishwasher is cracked and needs replaced. It takes just a few minutes to replace, just remove the nut after TURNING OFF THE POWER and take to your local par ... Dishwashers

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas


... GE 24 in. GSD2600GBB Built-in Dishwasher

My neff dishwasher tap light is on and there is dirty water in bottom of machine and it wont start another cycle


... Dishwashers

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2557 seconds