Having problems with your GE Nautilus 24" Built-in Dishwasher ?

My GE Nautilus dishwasher keeps PUMPING water "out" of the machine during the entire wash cycle. I have removed all covers in the bottom of the unit to see if anything is stock. Used vinegar and CLR to remove mineral deposits-- yet nothing solves the water being pumped out the drain hose.. what's next, please.. a solution !?!


Answers :

If this convert-able dishwasher is permanently installed, you will have to take off the lower access panel to get to the pump area. If it is still in a portable configuration, it may be easier to lay the dishwasher on it's back or side to do this. Now, examine the pump / motor assembly. There is not a separate water pump on this model. There is a diverter pump out solenoid which get's pulled down to direct the water out the drain hose for pump out, which is suppose to spring back out of the way to allow water to go up to the spray arms for washing. I suspect that the solenoid got to hot and the plunger will no longer slide in the solenoid. If this is the case, you can replace it with a WD21X802. If the arm and plunger move freely, check the spring, or for obstructions in the pump housing, or possibly the diverter arm in the pump housing has come loose from the shaft. The solenoid is the most likely.
Repair Help & Product Troubleshooting for GE Nautilus 24" Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My GE Nautilus dishwasher keeps PUMPING water "out" of the machine during the entire wash cycle. I have removed all covers in the bottom of the unit to see if anything is stock. Used vinegar and CLR to remove mineral deposits-- yet nothing solves the water being pumped out the drain hose.. what's next, please.. a solution !?!


If this convert-able dishwasher is permanently installed, you will have to take off the lower access panel to get to the pump area. If it is still in a portable configuration, it may be easier to lay the dishwa ... GE Nautilus 24" Built-in Dishwasher

Asko D3120 I have resolved the problem of pum always running by tilting the dishwasher but now I have a new problem of the pump not draining the water in the bottom of the dishwasher. I thought it was clogged so I removed the screen and filters but did not stick my hand in the hole to clean... I used the plunger for at least 30 mins. Then I tried to pour a little CLR because I have hard water. NOTHING please help me


In the bottom where the filter are, you can see a yellow 'thing'. Remove this and stick one finger in an try to rotate the pump wing. Try to remove particals that is blocking the pump.\015\012Or there is something in the drain hose. Try to drai ... Asko 24 in. D3120 Dishwasher

I have a kenmore dishwasher, model 587-1625. Noticing that are dishes didn't seem to be getting very clean. I removed the drain screen and cleaned, noticing a lot of hard water deposit. yet, it still drain. Now after cleaning it doesn't drain now what?


Check for a plugged air gap (on top of the sink) ... Kenmore Dishwashers

I have a pressure washer with a Honda gcv190 engine. The motor runs great but there isn't any water pressure. I removed the manifold and pump and found some mineral deposits and cleaned everything out and while attempting to reinstall the pump on the crankshaft I noticed the key was missing. Upon further inspection it appears that the key was missing from the beginning or had sheared off and then disintegrated. (There were a lot of metal shavings in the pump shaft recess). My main question is th


... Pressure Washers

I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher


Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

Dishes all cloudy and spotty. Maytag Intellisense plus 1996 dishwasher. I have real hard water that leave white calcium build up. I can remove and clean all of the lower spray arms and filter. How do I remove top spray arm to remand remove deposits? The motor sounds good, hot water, fill ok. On the inside top of center of arm where it meets the center input connection there is gunk to remove. How do I get to it? remove arm? thanks


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Danby 22 in. DDW399 Free-standing Dishwasher

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

My dishes are filled with white residue from the hard water. I've tried vinegar to cut it and new rinsing agents but nothing works. Is there a filter to clean out any hard water deposits? Do I need to check the line for plumbing for hard water deposits? My water softner is working fine, my dishes are filled with white all over them. HELP!


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Mineral deposits Our dishwasher is putting mineral deposits on our dishes (we clean them with CLR, put them in, and they come out nasty). So what's the deal?


Make sure ya prime the sink before starting the dw and use less detergant ... Kenmore 24 in. 16309 Built-in Dishwasher

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

We ran a cycle with 'Lemi Shine' a hard water treatment (Lime remover). After that cycle, the tub will fill and drain, but the water does not reciculate. So, I assume the deposits loosened and then clogged either the recirculation pump or a sensor that activates it. I don't know how to determin that or how to access the senors/floats. I do know if it's the pump that's clogged, I have to remove the thing and flip it on its top to access, but don't know the details.


Hi. Both the drain hose and recirculation hoses should be checked, asap. These hoses are connected to the pump assembly and they can also both become obstructed, as well. I would purge these hoses and check the pump filter and fine particle screen fo ... Bosch 24 in. SHY66C05 Stainless Steel Built-in Dishwasher

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hello! My GE Dishwasher (Model # GSD2000G00WW) will not fill. The water supply is flowing properly after cleaning out some lime and mineral deposits, but no water is going into the machine. If the water flow valve needs to be replaced (?), is there a local distributor in the Cincinnati/Blue Ash area in Ohio (zip code is 45242)? Thanks! Steve Brodbeck


I need to know is the water not going in the machine at all in other words when you switch on the machine with the tap open can you hear the water flowing,if you can here the water flowing check the hight of you drain hose if it is too low down you w ... Dishwashers

Ariston LS620A When running my dishwasher the dishwasher tablet is not disolving and entering the system. The dispenser is open but the tablet is stuck there??? I have cleaned the removable parts from the bottom of the system and put a new tablet in but the same problem happens again. This time when removing and cleaning the parts at the bottom there is water present and it hasn't drained is that normal? Or are there other parts there I have to remove....I have tried but nothing seems to budg


Hey, I experienced the same problem and I realized it happens when you block the water from the dispenser with a dish. Make sure that it is never blocked and the dishwasher is going to work fine ... Ariston Technologies LL64WNA Built-in Dishwasher

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

Model MDB5100AWW, sn 10493315YK. Dishes not coming clean, stuck on food, and cloudy. We have installed new Jet Dry, and operated unit in rinse cycle with added vinigar about 4 times with no luck on cleaning. We do NOT have a water softener. Do we have lime deposits that are not allowing water to properly. Are there components that we can remove and clean? Mike


The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the ... Maytag MDB5100 Dishwasher

Our 16 year old dishwasher takes way longer to finish cycles, has become very loud and now no longer cleans the dishes - especially the top rack and the silverware. We have hard water and I have run it with vinegar in a bowl 3 times and have been cleaning all the deposits I can today. It doesn't seem to be draining out all the gunk. Water flow seems ok, the arms have nothing blocking them. Any instructions for me to follow to clean out the mechanisms? Or has it run its lifespan... Thanks!


Parts are no longer available for your dishwasher. Typically - manufactures end support after 10 years.Your hard water deposits will never come all the way out. They will be "clean" for a month or so until another calcium chunk breaks free and ... Dishwashers

I want to remove the white plastic wheel that propels water into the circulating arms. It is held with one screw which I cannot seem to be able to loosen. This white plastic wheel has 2 small holes in the surface which are perhaps there for some special tool to hold the wheel stationary in order to loosen the screw holding this wheel in place. Underneath this gray plastic housing is the heating element. I want to remove it in order to clean accumulated deposits of gunk.


It's reverse threaded. ... LG 24 in. LDS 5811 Built-in Dishwasher

My Jackson CJ 20 is heating the water all the time, it stops after washing the dishes for 10-15 min and does nothing and after that i have to switch it off and turn it on again to wait another 10 minutes to heat the water and pray that it'll work. How can I solve this problem?


... Jackson Dishwashers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

Flashing lights My GE model # GHDA455L00CS Quiet Power a dishwasher's lights are flashing when I start it, will not reset or in-take water. I've tried unplugging it and restarting. Nothing. Tried removing door door screws and press down door latch. Still nothing. HELP!!!!!!! IT WILL NOT PROGRAM. IT HAS A FLASHING LIGHT. WE HAVE BOUGHT EVERYTHING BUT STILL DOES THE SAME THING


It mite be the circut board problem..just  re-soldered a few of the pins in it and things will be back in working order. ... GE Profile PDW8400J Built-in Dishwasher

Poor cleaning ; leaving what appear to be small specks of calcium or some other mineral deposited on surface of dark colored plates. Glassware streaky. Washer cycles normally. Have noticed fairly heavy deposits on surface of dryer element. Any advice appreciated. Hard Water.


Hi,Check your heating element.. Dishwasher ... Maytag MDB3100 Dishwasher

My Whirlpool dishwasher ADP951 does not start at ll. I think I turned off the machine last time before it completed its cycle. I found there was water left at the bottom unlike after a usual run. I manually removed all the water and mopped it all. yet it would not start at all as if no electricity comes into the dishwasher. Please help.


If your dishwasher is on a wall switch, someone may have shut it off, Your dishwasher could be pluged into a Daisy chaned GFI, check all your GFI in the kitchen and make sure none are triped. The home Fuse Box, make sure the braker is not triped. ... Dishwashers

Hard water deposits oon bottom cant even remove filter,,water isnt reaching top to clean


Check this link here ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1734 seconds