Having problems with your GE Nautilus 24" Built-in Dishwasher ?

We use well water and I don't have a stainless steel dishwasher, so the tub has gotten very dirty looking with time. How do I clean the tub?


Answers :

Just good old elbow grease. Thanks. No need for further contact.
Make sure there is no detergent in the dishwasher. Put the dishwasher in "Rinse and hold" cycle and start it. Once you hear it starting to fill with water, open the door and pour in a cup of white vinegar. Resume the cycle. You also can try using some citric acid. If all that did not help try this.
Repair Help & Product Troubleshooting for GE Nautilus 24" Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We use well water and I don't have a stainless steel dishwasher, so the tub has gotten very dirty looking with time. How do I clean the tub?


Just good old elbow grease. Thanks. No need for further contact. ... GE Nautilus 24" Built-in Dishwasher

I own a GE Profile GSD 4330 dishwasher. Recently it has been leaving some water in the bottom of the tub. This water accumulates over time until the entire bottom is filled. I have checked the air vent, garbage disposal unit and the filter in the bottom of the dishwasher (which was filthy). I cleaned the filter and everything else looks okay, but it is still leaving some water in the tub.


... Dishwashers

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

Glasses int he top rack of my kitchenaid dishwasher don;t get clean. they finish the run spotted and covered in what looks like baked on dirty dishwater. dishes in the lower rack look ok, but the silverware is always dirty, too. i figure it's one of two things - either the top sprayer isn't working, or the machines doesn't drain the dirty water well enough. or maybe it's something else - cycle regulator? the machine is about 4 years old. thanks


If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is to add some vinegar to the bo ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishes and the dishwasher look dirty after they run, like it redistributed dirty water. The door is very dirty/filmy except right under the soap dispenser, like someone squirted dirty water on it but wiped right under the soap dispenser. If I run it a second time with vinegar it gets clean, but that is crazy, esp since it takes 2 1/2 hours a load. I have 2 of them and both are doing it. I have changed soaps, added more soap, used less soap, pre-rinsed dishes, put them in filthy, used jet-dry, no


Hi Mike_wend604,\015\012\015\012I am looking for a used Asko #1504, if you would like to sell yours please e-mail me at [email protected] and put "Asko" in the ... Dishwashers

I have a bosch SGV43A03GB/42 dishwasher. The cups / plates were coming out dirty so I did all the drain cleaning and ran finish dishwaher cleaning fluid. What I noticed was the top arm wasn't rotating and the source of the problem. I took out the arms and cleaned the holes to ensure no blockages but still a problem. I bypassed the door switch and found that theer was no water being pumped out to the pipe that leads to the top rack. I opened the two torx screws and looked beneath pipe to find wha


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SGV43A03 Built-In Dishwasher

My GSM2260N10SS under sink dishwasher runs and cleans well, then fills partly back up with water when it's not even on. The water is dirty looking.


The dishwasher drain line is mounted too low.It should come up and be attached at 30 inches under the sink,then come back down for the spout to attach to the drain source.The dirty water is backing up into the dishwasher from the kitchen ... GE Spacemaker GSM2260NSS Full Console UndertheSink Dishwasher with 5 Wash

My Miele dishwasher is about 16 months old. Initially it was awesome. Now it doesn't get anything truly clean on any rack. Every item has scum and traces of food or drink left on it. I've cleaned the filter and the no-return valve, and refilled the salt (yes, I used the right one) and rinse aid. The manual has no other instructions to remedy dirty dishes. The water is hot, and the machine seems to be running just fine. Where should I look for a problem?


The other possible problem is that the spray arms have small bits of food (sesame seeds are nasty!) stuck in the holes. Take the arms off and flush them out. You might need to poke out seeds that are stuck in the holes. ... Miele G880 Dishwasher

The dishes have recently started coming out of the dishwasher with a nasty film...it looks like they are not clean. There is no standing water - we've added more fluid to the rinse cycle. They still look dirty.


Hi\015\012\015\012The first that you should check is the water inlet valve, try to clean the inlet and the water line going to the unit. After this if the problem is not solved then you have to take the unit apart to clean the spra ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Dishwasher leaves food on dishes, glasses still look dirty after being washed - I have cleaned the filter and the inside of the dishwasher - checked hot water temp. I use dishsoap tabs.


Are the holes on the spinning jets bloked with old food or lime scale?\015\012if so take them off and clean them out. ... Whirlpool Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Dishes don't get clean, dirty water stands in bottom of dishwasher - looks like coming from disposal/sink


Sounds like the main drain is stopped up.The problem is that the water can not drain from the dish machine,because of a blocked main drain .The drain is blocked under the disposal,This may be a bigger job removing the disposal.Is water standing in th ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Model MDB7100AWQ serial #15868872YU - Dishes are dirty after completing cycle, dishwasher soap sitting on door and on dishes closer to soap dispenser - checked for the water being hot during cycle and it was - looking for a filter to clean but couldn't find one - what should I do


Hi,From what you have said here it would sound like either a spray arm or a pump problem...my bet would be on the spray arms....They have a way a getting stuff in them even with filters and such...also the silly way they are attached ofte ... Maytag Dishwashers

During the last cycle, my dishwasher stopped and now will not restart. There is a layer of water in the bottom. Looks dirty. I found a plastic top to a waterbottle that had fallen in the tub. Maybe that is what caused it to ATP but now it won't restart. Thank you!!


It is not possible for me to read the solutions the other consultants would hvave provided. But I assume you have tried to reset by turning the power off and on.\015\012\015\012Please provide the full model no. of the Kenmore dishwasher. ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Kitchen aid tall tub dishwasher model #KUDCO3IVWH Yesterday the top rack didn't clean, today both racks stayed dirty - took apart the food chopper assemble and notice that there is water in the well is it ok to remove the food chopper blade? what else could be wrong


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher

Dishwasher won't drain, tub is full of dirty water. how can i clean out the soil collector?


... Amana ADB1600AWS Builtin Dishwasher

I have a 13 month old (Thanks Sears warranty!) Kenmore Portable Dishwasher Model 665.17769. It drains poorly, taking 2-3 times after load is completed running thru the ''cancel/drain'' cycle to clean it out. It is not getting dishes clean either, presumambly because the dirty water isn't being flushed out at cycle end and instead of rinsing with fresh water, it's still screwing with the dirty water. Manual doesn't offer any advice except to see if the hose is kinked (it isn't). I made sure nothi


Hello Linda it sounds like you may have a piece of glass or some other hard material in your drain pump which is partially blocking the draining process. Remove the hose in the base of the machine, then unscrew the drain pump and physically examine ... Kenmore Dishwashers

The inside of the dishwasher used to sparkle & clean the dishes very good, now the dishes look dirty & inside looks dull with a white film. I have tried cleaning filters & taking arms offs to check for blockage, making sure the Jet Dry dispenser is properly filled, the hose going to the dishwasher does not appear to be kinked, how would I check inside the dishwasher to see if it's kinked there? Do you have any other suggestions? please help!!!!


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 23 in. SHU33A Built-In Dishwasher

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda


The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

We have a kitchenaid dishwasher, kudi22ot3, installed in 1992. It is not cleaning dishes even thought the tub is getting water, and we've run dishwasher magic through it a couple of times. The dishes will get clean for a few runs, and then will stop getting clean. Is it time for a new dishwasher or can this one be fixed? Thank you.


Hi,There are 6 major reasons that could affect the cleaning.A nice guide you could follow is :-http://www.partselect.com/dishwasher+dishes-not-clean+repair.htmOther than this, you need to check the pump. Make sure ... KitchenAid Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2602 seconds