Having problems with your GE Nautilus 24" Built-in Dishwasher ?

The inside top of dishwasher has a part that spins to spray water but keeps falling off ? Looks like it just snaps back in place, but falls off during normal use ????


Answers :

Your going to need to order that part that fell off the thing is yes it does snap in but ones those snaps wear out then you have this issue when the water pressure is thrown at it to make it spin. Also make sure you not overloading the top tray because what happens is this thing turns and hits something and from the force it knocks loose. I would recommend ordering that part.
\015\012
\015\012
\015\012Thanks and please do click the accept button for my efforts.
Repair Help & Product Troubleshooting for GE Nautilus 24" Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The inside top of dishwasher has a part that spins to spray water but keeps falling off ? Looks like it just snaps back in place, but falls off during normal use ????


Your going to need to order that part that fell off the thing is yes it does snap in but ones those snaps wear out then you have this issue when the water pressure is thrown at it to make it spin. Also make sure you not overloading the top tray becau ... GE Nautilus 24" Built-in Dishwasher

I borrowed my neighbor's Karcher Model G 2650 OH (it's several years old). It had the yellow tip already on, but after awhile, I took the tip off to use a different tip,and pulled down the brass coupling at the end of the wand to insert the new tip. The problem is that the brass coupling at the end of the wand won't snap into place around the tip -- so I tried another, and another. No luck. And now the original tip that was on the wand won't snap back into place. HELP! I need to get my neighbor


... Karcher Pressure Washers

Frigidaire dishwasher model FDB857RJS1 not pumping water to the top arm. runs then makes a grinding sound like the motor skipping a gear then back to moving water but not enough pressure to get to the top arm.Unit drains normal runs all cycles but leaves the soap on the door not used.


HI, under the sump housing, there is a major issue concerning the circulation motor. there is a wash impeller that is connected to the circulation motor, via drive shaft and stud. this assembly has been stripped ... Frigidaire Dishwashers

Upper spray arm and tube assembly. This part fell off the back wall. Can not figure out how to get it to stay on again. Looks like it should clip in, but nothing to snap it in place. The part does not look brocken when compared to the part would order to replace. No info in the manual and their service department was no help, How do I fix this.


Hi,\012Those p[arts wear and even though the parts do not look broken they are not up to the specs. of a new part...\012That is not that hard to fix and you can easily buy the parts yourself online... ... Bosch 23 in. SHU 8805 Built-in Dishwasher

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

My whirlpool dishwasher is not washing the dishes properly. when finished cycle, I still see the dishwasher tablet half used. The grey long piece at the back, seems to have come out of the two holes it fits into on the "floor" of the inside of the machine. I've clicked it back into place, but it still pops out. Sometimes the rotating sprayer at the top and bottom, don't move either when its out of place. please help.


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Bosch SHU8805UC/14 dishwasher. I took the front door panel off to install it better but ended up with two extra pieces that look like either part 935400 Door Guard, or 935526 Support. I cannot seem to find any place on the inside of the door where these pieces would fit. The dishwasher works fine but seems like it got noisier after I put it back together without these two parts. Can you help me locate the proper place for these 2 plastic parts?


Hello, \015\012\015\012Welcome to FixYa.\015\012\015\012I believe the parts you are referring to are likely the blocks in each corner of the outer door panel. These have been a sticking point for many I tech over ... Bosch Dishwashers

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Dishwasher runs full cycle, however, the dishes and glasses have small particles of food dried on them when done. I do rinse all plates and utensils before turning on. I run on a normal cycle, no heat dry. I use cascade action paccs 4X concentrate. Which appears to not disolve completey, the packet. It normally does. There is no water back-up in sink, and I also open the trap ,no blockage. Please help, Dan


Hi Dan and welcome to FixYa, I am Kelly \015\012\015\012 Most of the time when you start having dirty dishes post wash there is either an internal blocked screen under the lower wash arm tower or a problem with the drain. ... Dishwashers

I have a white chalky reside on my dishes after running the dishwasher. It looks like it has come off once I rinse them and they are wet, but when I dry them again it is back. I have a water softener, so I know it is not hard water like everybody seems to be suggesting. What can I do or use and what could be the cause of this?


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Maytag MDB8551 Built-in Dishwasher

Our 2470scvi has caused all of our glassware to turn white. we use very little soap and we always use rinse aid. It seems to me that it is not rinsing properly. It actually has a sound for about 10 seconds that sounds like a motor is stuck.. This sound occurs twice in each cycle. It seems to wash ok but not great of which I would expect for a supposedly top of the line machine. This problem has always happened and the machine is 3 years old.Is this normal for a miele? If so its not the machine w


Hello macit. I do not blame you one bit for being disgusted about this machine. Let's do this. Empty it out and pour in 2 fulll cups of white cider vinegar. Close the door. Let the hot water run into the kitchen sink until it is as hot as it wil ... Dishwashers

Quiet Partner II Whirlpool Dishwasher 2 years old, used about 6 times in 2 years. Panel LED's flashing like a Christmas tree: Pots / Normal / Sani / Cancel lights all flashing Tried different resets as found on web but none work. Dishwasher was NOT being used when the flashing started. Need reset sequence if there is one.


Unusual LED or\015\012Display Readouts\015\012Open ID diodes and/or LED\015\012circuit(s) in keypad, or open\015\012ci ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.


... Bosch Dishwashers

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Bosch Model SHE43F Dishwasher, only 1.5 years old. The door will not lock all the way like the latch is broke. But the dishwasher still works as normal without locking the door. The last time I used everything was ok. Looks like a programming problem, or latch mechanism broken.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. From what you have described the\015\012issue seems to be with latch mechanism as the Dishwasher is worki ... Bosch 18 in. SRV43M03 Built-in Dishwasher

I would like to purchase a Moyer Diebel U/C dishwasher for residential use. I have the option of purchasing a used dishwasher - it could be one of three models. Which one is the model he is trying to sell to me? 1. 501 HT 2. 501 HTN 3. 501 LT the owner states the voltage is 120/208-240 and heats between 150 f and 180f.He notes there is a 4 ft. cord at the back without a plug on the end of it but the model is rubbed off of the serial number tag.There are three switches on the lower right hand co


The way you mentioned the unit have a 4 ft. cord at the back seem like a 50l LT the best way to determent is open up the bottom plate and see whether there is a booster tank in the right hand side. \015\012Hope this can help you. ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

We have a Kenwood KDW8ST2A Dishwasher which is about a month old. The other day we had to pull it out from under the worktop because something rolled under it. When we put it back and went to use it later that day, we got an E1 error code appear and it's been like that since. We pulled it back out to make sure that we hadn't accidently pulled or loosened any of the pipes. We have the manual which does tell us what the error means but it doesn't tell us how to fix it. I'm sure it must be somethin


You can find a manual here ... Dishwashers

2 weeks ago, I had a plumber come and put in a new garbage diposer and since then somewhat old/dirty water seems to be sitting at the bottom after all cycles are done. I calle dhim back and he says that there is no problem in the plumbing but more with the pump. I even use the wt/dry vac and removed water and ran it but still comes back with water at the bottom. also the dishes smell like soap. Help!!!


The plumber did not make an air gap in the dishwasher drain hose when he reattached it to the new disposal. Look under your sink, does the hose (attached to the disposal) go down and through the cabinet? If so, that is definitely the issue. Simple ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Troy bilt 2600psi 2.3gpm model 160 pressure washer, I hooked everything up like normal, It cranked up fine, when I pulled the trigger on the gun it stalled. When I try to crank it back up the cord wont even pull like its stuck any suggestions would really help me tks..


This sounds like the pump has dead headed. I.e. the unloader valve is sticking. Unhooking all of the hoses should eventually allow everything to free up. Once it is free what you should do is add about 3 ounces of oil into the water inlet connecti ... Pressure Washers

I have a Maytag model DWU9502AAM dishwasher, took out the top rack (easy) to wash furnance filters, and cannot get the rack back in rightly! Where are the rollers on each side supposed to be placed to hold the rack? Do the snap supports face up or down on the rack? I broke two of the roller snaps and replaced them, still no luck. Does anyone have a schematic??? Maytag has nothing on this I can find. Thanks!


Hi there,\012Well you can try from upside face...... there are some plastic lock type grips... for more information you can download the repair manual, please follow the below link -http://cgi.ebay.com/_W0QQcmdZViewItemQQitemZ ... Bosch SHU9915UC Dishwasher

No Power Hi Timon90, I used the dishwasher like normal yesterday today I went to use it and there is no power at all. I have checked our electricity box and none of the switches are tripped. I have put the door in as hard as I can and have checked whether the electricity plug has been pulled out by accident. Can you suggest anything or should I call a serviceman. Thanks from Julie


Remove the door skin dont forget the two screws under the door in the middle,the control panel will lift off remove the power board(unclicks)remove the plastic case and see if its blown.But first also remove the lower kick plate at the front and chec ... Asko 24 in. D3350 Dishwasher

Normal wash cycle will not work. After I used the rinse cycle on day, I went back to the normal cycle and the lights wouldn't light up. Every other cycle will still run except this one.


Could be tricky to find this one.\015\012\015\012You need to deduce what is used in the main cycle that is not used in the others,\015\012Whatever is used is likely to need testing or replacing.\015\012If there is nothing else ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0733 seconds