Having problems with your GE Nautilus 24" Built-in Dishwasher ?
I have a G E Nautilus Power Scrub Dishwasher
After our washer has gone through its' cycles water remains (about 2") in the bottom of the machine.
What to do?
Repair Help & Product Troubleshooting for GE Nautilus 24" Built-in Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a G E Nautilus Power Scrub Dishwasher After our washer has gone through its' cycles water remains (about 2") in the bottom of the machine. What to do?
... GE Nautilus 24" Built-in Dishwasher
My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????
First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher
I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet
First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers
GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you
... GE Dishwashers
Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button
The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers
Bosch compact Logixx dishwasher (8401) will not start after it did turn on to start a cycle. Pump made laboured draining noises then seemed to cut out. Water remains in the bottom after last cycle.
... Bosch Dishwashers
Water remains at bottom after dish cycle is complete . Dishes come out clean and everything seems normal except for the water that remains at the bottom of the dish washer. I realize that a small amount of water is usually there but this is too much.
Set the controls to off then power off at the mains for 30 mins and then power mains back on and run a drain program or a full wash program. If the water won’t drain away then the most likely problems are the door interlock switch is faul ... Whirlpool Dishwashers
Once cycle is complete, water remains at the bottom of the dishwasher (inside the dishwasher - level of water remaining up to the element/heater). Dishwasher GE Profile Model PDW7712J00BB Ser. TF615328A My question: How to eliminate all the water once cycle is over? Thank you, Nicole
... GE Dishwashers
GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?
Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher
Water remains in the bottom after cycle. I drained the water and seems there is gunk in the bottom. Running the rinse cycle with some bleach?
Hi,Here is a tip that I wrote that will help you with your problem...http://www.fixya.com/support/r4078724-dishwasher_problems ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher
My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....
CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??
You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers
My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.
Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
My whirlpool adp 553 dishwasher stopped mid-cycle with water in bottom, no power light. Power light goes on if door is opened. Can you please help me?
... Whirlpool 24 in. DU948PWPQ Built-in Dishwasher
Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!
I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers
I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's
... Kenmore 13719 / 13712 Built-in Dishwasher
I have a kitchenaid dishwasher model number kudso2sr and there is standing water in the bottom of the unit after the cycle is complete. The water will not drain. I ran another cycle and the water still remained. Please help
You may have a vacume issuealong side of the dishwasher itself there is a loop of drain hose to create a trap - inspect. also inspect where it is hooked up & follow where the drain hose goes to it's final connection to be sure there are ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher
My Frigidaire Model FDB2810LDC1 dishwasher will not stop running. Seems to complete a normal cycle and different cycles can be selected with normal time countdown but at end only rinse agent low light remains lit and sounds as if pump is still running. If opened, water appears to be streaming from rotator arms. Have cycled power but symptoms remain.
... Frigidaire Dishwashers
Water remains in bottom of tub after cycle is complete.
For Miele Dishwasher G2470SCVI Need help with remaining water in the bottom. Model# G2470 SCV1 SF Type-HG03. Runs through the entire cycle,long,short ect..everything is clean and dishes look great but
See this causes and fix it. God bless you\012 \012 \012 \012 \012 Belt, Water Pump\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers
Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.
Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher
Whirlpool GU1500XTLQ (2004). Having a major problem with soap suds. No matter how little soap we add, the suds remain at the end of the cycle and will somewhat still remain after running another rinse only cycle. We have verified that the water is flowing to the dishwasher and the top and bottom arms are rotating.
... Whirlpool Dishwashers
I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.
Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
Our 8 year old integrated 2 draw dishwasher (top draw) has a problem on the rinse cycle and constantly beeps and water at the bottom of the draw remains. I have cleaned out all the grit and stuff residual water and tried to use again. But alas there appears to be a blockage still on the rinse cycle. Can you help or do I need to get a plumber? Thanks...Louise
Sorry i lost you my breaker tripped ... Dishwashers
I have a GE Quiet Power 3 dishwasher and water is not draining completely after the wash cycle completes. There is about an inch of risidual water in the bottom of the washer after the wash cycle is done.
... General Electric Adora GHDA670N Built-in Dishwasher