Having problems with your GE PDW7380NSS Stainless Steel Dishwasher ?

I have no wiring diagram for my dishwasher GE model PDW7380N00SS. There is a green wire with a yellow stripe that is loose at one end and visible when the kickplate is removed. Where should this wire be attached?


Answers :

Sounds like a aground wire. Normally green or green with white/yellow stripe is ground. Is the dishwasher still functioning properly? If it is I would strongly suggest it being a secondary ground more then likely attaches to the frame of the unit. You may be able to see where it goes by lookin under but probably not without turning it up pside down.
Repair Help & Product Troubleshooting for GE PDW7380NSS Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have no wiring diagram for my dishwasher GE model PDW7380N00SS. There is a green wire with a yellow stripe that is loose at one end and visible when the kickplate is removed. Where should this wire be attached?


Sounds like a aground wire. Normally green or green with white/yellow stripe is ground. Is the dishwasher still functioning properly? If it is I would strongly suggest it being a secondary ground more then likely attaches to the frame of the unit ... GE PDW7380NSS Stainless Steel Dishwasher

There are two hoses coming from my Bosch SHE45M06UC dishwasher. One is obviously the drain coming from the back of the unit, and the other is attached to the side looped and not connected to anything. I went online to the Bosch website for a installation manual and it describes this hose as a air venting hose. Does the end attach anywhere or does it just hang loose on the unit. My husband detached it from its original position and thought it was part of the water line. HELP!


Many people realize the dishwasher connects to a little hose on the sink, it is called an air gap. However, many people wonder " The air gap is there to prevent the water from being siphoned out of the dishwasher. When water flows through the drain ... Bosch Dishwashers

Maytag mdb8600 I am replacing the latch mechanism and have 3 wiring connectors. Not sure how to connect them back to the new latch. The first one has 4 white wires, the second one has 4 black wires and the other has 2 black and one purple wire and attaches near the top of the door....I was looking for a wiring diagram but hoping you might be able to help


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

I'm installing an electrolux dishwasher, the first thing I'm going to do is the electric wire. I know I have to attach the black white and green (ground wire).I've done this before with my Maytag and it was a breeze. When I open the elec. box on the electrolux dishwasher the black white and green wires go into the box from the Dishwasher and then THROUGH THE BOX AND THEN BACK INTO THE DISHWASHER>>>>>THERE IS NO END........... In the Maytag I just opened the box on the dishwasher and the ends of


There should be a complete wire connection already there ready to be plugged in. If not, typically at the back of the unit there should be a black plastic box that when opened will indicate 3 terminals. live - neutral - and earth. Looks to m ... Electrolux Dishwashers

HI. Trying to install a LDF6920ST Dishwasher. Question about the wiring. The wires coming out of the machine are Black, Green with a yellowish stripe and White (the white one has a label attached to it with a "N" on it). The plug wires are 3 side-by-side. They are gray, green and gray. Which wires do I connect with which wires?.


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

My LG Dishwasher LDF7932ST has White, Black and Green wires coming out of the unit, no problem there, however the ALL Grey Cord that was in a separate bag does not help me identify which wire is white and which wire is the black, I can only see that the green wire is in the middle of the three attached to the grey cord as I can just see a little bit of green, how am I suppose to know which ones are the other two? I tried pullilng back the grey rubberized cord to see if it was show me ... but no


Hi,\015\012\015\012There is a simple way to tell is to look at the plug end of the cord...\015\012The blades on the plug will be two different sizes...\015\012The blade that is the larger of the two will be the white wire... ... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

I'm attempting to reuse a Maytag dishwasher motor for a bench grinder. Since this is a reversible motor, I'm not sure how to connect the wiring to a simple switch so that it works in one direction only. The motor has 4 wires: blue, gray, red, yellow. Not sure which to connect to the hot (black), return (white) and ground (bare) wires from the romex and can't find a wiring diagram online for this dishwasher. Any ideas? Thanks.


... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.


I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers

My Ge triton xl dishwasher, model PDW739n00ss has a green wire with a yellow stripe that is not connected to anything. It is laying on the floor. I cannot find the wiring diagram. Where should this wire be attached?


... GE PDW7380NSS Stainless Steel Dishwasher

The upper rack side rail is loose where it attaches to the side wall of the dishwasher. It allows the upper rack to wobble. When the dishwasher is turned on, the force of the water pushes the rack forward so it detaches from the water supply and the arm does not rotate. The arm and connection are all clear and the arm is able to rotate, so those problems are not a factor. The wheels are in good condition. The left rail is a little loose; the right one is very loose. There must be a way t


Hello melinda.... Here is a link to searspartsdirect.com ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Burning smell from our Dishwasher. I opened it up and found a little square brown thing attached to the motor - It has a terminal at one end that a white with a coloured stripe cable attaches to via a slip on terminal and 2 terminals to slot the little unit directly into the motor. Anyway, this little unit has obviously burnt out and this is the problem. Except my problem is that I dont know what this little unit is, so dont know what to ask for at the spare parts centre. Can anyone identify


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Bought suction hose for karcher in order to use water from bucket. Have attached hose but there is no water being sucked from the bucket . One side of hose attached to washer the other dropped in bucket is this right? The end in the bucket has no suction, and a depressable valve that seems to be impeding the water suction. Do I remove this valve ?


... Karcher 26408500 Pressure Washer 25Foot ExtensionReplacement Hose

Installation we have two loose white acordian type hoses, one attached to the side of the unit and the other comes from underneath. Do we attach both hoses to the drainage under the sink, and if not where does the hose go that does not go to the drainage under the sink?


It sounds like you have connected your dishwasher to a garbage disposal.\015\012\015\012\015\012The 2 hoses provided with your dishwasher connect together. \015\012You run the drain hose through ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Our Asko D3112 was not draining, so we had maintenance drain the hoses to clear any blockage but it did nothing. They said it must be our pump not working. I ran one more cycle to see if things went back to normal, however now our pump won't shut off. We have to unplug the machine just to get the pump to stop. We had a repair technician come to look at the dishwasher and he says that it is a problem with the control panel/computer system. Something tells me it is a merely a loose wire and that w


Check your manual to see if you have a drain pan at the bottom of the unit, and a 'float' that checks for water collecting there. On at least some Asko models, water collecting in the pan causes the float to rise, which then changes the operation of ... Asko 24 in. D3112 Free-Standing Dishwasher

I was installing a thermal cutoff, one of the wires came loose from the thermal block while i was reattaching the panel and cause a spark. Now there is no power from those leads. Is there anything else that could have shorted out in the dishwasher?


Hi,\012Check the control board... if your lucky the board has a fuse in it that blew... if not then the board is fried...\012\012heatman101 ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

We cannot keep temperature of our Jackson Tempstar dishwasher at a constant temp. One time the rinse will be down a bit and then the wash. We have replaced the gauges, thermostats, motor and element of the diswasher. It is kept constantly clean, and we have tried everything we can think of. Would there be a wire that could be coming loose every once in awhile that may cause this? Thank you for any help you can give us.


... Jackson 25 in. TempStar HH Free-standing Dishwasher

Jdb2100aws dishwasher - door handle fasteners loose, handle ready to drop off. This is a dissambly question: The middle section of the door has an upper one-third (which contains the input switch strip) and a lower two-thirds; the upper section must be removed to tighten the door handle fasteners. After wiring is disconnected (yes, power is OFF), the upper section appears to be held to the shell by some kind of barbed fastened from the inside, run through a tab on the door shell and into a fema


After removing the stainless cover l tried to disassemble the door further but found it difficult, there is a hard thick plastic cover, i took my dremel and cut a small hole large enough for a wrench to fit and tighten the thin nut on the handle, lin ... Jenn-Air 24 in. JDB2100AWS Built-in Dishwasher

I brought my 2 yr old Kitchenaid model kudp01dl over from my foreclosed home to install where I live now, and the left side of the touchpad to run a load doesn't work anymore. I know one wire had jostled loose underneath, and my husband re-connected it to it's terminal, but could there be another I am not seeing as well? Or any other ideas? It still works fine to cancel, drain, and select drying options, etc, but I can't start a load!!!


It Is SOMEWHAT Common for WIres / or PLUGS to Come looes on Apliances Your Husband May need To Remove A Pannel and Thourelt INSPECT FOR this what you DISCRIBEVARY WELL MAY BE AS SIMPLE AS 1 WRE OR EVEV 1 PLUG OR WIRES THAT IS DISABLEING THE UNIT FROM ... KitchenAid 24 in. KUDP01DL Built-in Dishwasher

I have a kenmore quiet guard standard dishwasher. About 2 weeks ago it started leaking. today I pulled it out and found that looking straight ahead at the door on the lefthand side under the bottom is 2 small wire metal fittings that screw up into the bottom of the dishwasher. one was loose and dripping water. when i screwed it back in i noticed that it was stripped out. can it be replaced or should I scilicone around it to stop it?


... Dishwashers

I have a GE profile dishwasher with the controls on the door edge. my handle for the door has become loose on one end. how canI tighten the handle. doI have to remove the entire panel on the door back?


... GE Profile PDW8060GSS Built-in Dishwasher

Two yellow wires with spade connectors under the machine are not


... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

I have a frigidaire dishwasher model fdb750rcc1. The wires somehow came loose while trying to fix the handle. I found a place for each wire via the wire diagram, however there is a green wire loose and I cannot figure where this wire goes.


... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Loose wires.one white and one black at bottom of dishwasher


The black wire is the HOT wire ... it should be connected to 120 volts AC .. the white wire should be connected to the neutral/return wire (also white) ... the incoming AC line shoiuld also include a bare ground wire .. that should be attached to a ... Dishwashers

My Indesit dishwasher needs to have the micro switch aquastop replaced but not sure which wire goes on which contact on the switch. Two wires , one pink and one brown.


... Indesit 24 in. DI67 Free-standing Dishwasher

GE Diswasher Mod# GSD900L-01. The guide wires attached to the springs on the door have broken. Need to get new wires, and instructions how to re-attach the wires to the springs and the door. Thank you.


The door cable is here: \015\012\015\012http://www.appliancepartspros.com/part_details.aspx?part_id=2038829 \015\012 ... Maytag Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0876 seconds