Having problems with your GE Profile PDW8400J Built-in Dishwasher ?

Water will not drain from unit. Water on bottom of unit appears to be clean with no evidence of food debris or soap.


Answers :

You need to check the drain hose first. Make sure that it isn't kinked or blocked and that water is flowing through it properly.
\015\012
\015\012If the hose is ok then the problem is likely to be with the drain pump and it will need looking at.
Repair Help & Product Troubleshooting for GE Profile PDW8400J Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water will not drain from unit. Water on bottom of unit appears to be clean with no evidence of food debris or soap.


You need to check the drain hose first. Make sure that it isn't kinked or blocked and that water is flowing through it properly.\015\012\015\012If the hose is ok then the problem is likely to be with the drain pump and it will need lookin ... GE Profile PDW8400J Built-in Dishwasher

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

Dishwasher drain is hooked to a food disposer and until recently the unit worked fine. Last week following a cycle a couple of inches of water did not drain out. All food is removed from dishes, silverware, etc. prior to loading and the food trap in the bottom is completely clear. I ran the unit empty through a Lightwash cycle and afterwards the water level (that which didn't drain out) looked to be the same as before. The dishwasher is run 2-3 times weekly whereas the food disposal is


Hi, The I don't think the problem is with the loop and the 32" above the floor.If the dish washer was removed from one house to another, did *********** ever have a dish washer in the house before that he replaced this one with? The reason I am aski ... Dishwashers

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

My Kenmore Elite dishwasher (model 665.17462300) is not spraying the water from the basin in the bottom up through the rest of the dishwasher. The basin fills with water, then just makes a humming noise and appears to splash a little of the water around the very bottom of the dishwasher. When we cancel the cycle, it does drain out the water from the basin. I cleaned all the gunk and debris out of the basin in the bottom, but it didn't make any difference.


... Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I've had my Nautilus for 6 years and it cleans very well - but now, it won't drain fully and pools at the bottom of the unit. I have made sure that my garbage disposal was cleared first, too. and that water was draining properly in the sinks. I will need special tools to unscrew the drain filter in the dishwasher, right, or can I just use a pair of pliers to turn the little knobs? I am always careful to rinse all food off the dishes before putting them in the washer, but I guess I wasn't careful


If your model has the screen across the back with the filter, then yes use your fingers or a plier to unscrew the pop up valve assembly at the very back center of the dishwasher. Most likely, the cone shapped part has deteriorated and is not sealing ... GE Nautilus 24" Built-in Dishwasher

Hi experts - My dishwasher won't drain properly. There's several inches of standing water in the bottom of the unit. During the drain phases of the wash, the motor underneath doesn't spin and a buzzing is coming out of the motor relay. During the wash and rinse phases, the motor runs fine and all appears well. Any thoughts? Thanks!


Either the water outtake or the pump are clogged - you will have to remove it to see where's the problem. ... Frigidaire 24 in. FDB679GF Built-in Dishwasher

Dishes not clean. soap doesn't appear to be distributing through dishwasher; instead there's a soapy film all over the inside walls, door, and bottom of the unit. I have a water softener in the house, so it's not a hard water problem. Jet Dry is also full.


... KitchenAid 24 in. KUDS02FR Built-in Dishwasher

The dishwasher does not appear to be draining properly any more. There is soap residue on the door after it runs. Also ther s a small pool of water by the food drain after the cycle ends. The glasses all have a residue on them after the washing cycle ends


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Asko 24 in. D3121XL Free-standing Dishwasher

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

The water will not drain out of the bottom of the dishwasher...soap suds were everywhere spilling out on the floor After it was mopped up, I scooped out as much as I could. Appears the water has gone down...why would the suds spill out? Afraid to try again.


Pull the dishwasher out and inspect the following:Check the hose for kinks or food plugging the drain hosecheck the drain valve solenoidcheck the pump motor to make sure it's able to reverse ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Cutlery is cloudy and dirty, some food is dried onto knives and forks. Cups and glasses are cloudy and not clean on inside. Coffee or tea stains are not removed. Plates and soup bowls seem OK , and water is draining properly. We have tried with less soap, more soap, gels, tablets and powders but to no avail. The dishwasher does not clean dishes etc, as as it once did. There doesn't appear to be any problem with the 'cycle'. The machine is about nine or ten years old, and has run fine until ve


Don't know much about Dishwashers but have you tried a descaler.Is the water spraying out as normal.Is the water actually getting hot, could be a heater element problem.If you look here you may get some other ideas just by loo ... Dishwashers

Cutlery is cloudy and dirty, some food is dried onto knives and forks. Cups and glasses are cloudy and not clean on inside. Coffee or tea stains are not removed. Plates and soup bowls seem OK , and water is draining properly. We have tried with less soap, more soap, gels, tablets and powders but to no avail. The dishwasher does not clean dishes etc, as as it once did. There doesn't appear to be any problem with the 'cycle'. The machine is about nine or ten years old, and has run fine until ve


They must have changed the way they treat the water in your area. those spots are caused by hard water. www.dishwasherfilter.com has a product out for this problem. it filt ... Bosch Evolution 300 SHE43M05UC Stainless Steel Built-in Dishwasher

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Doesn't appear to be washing the dishes like the spray arms are not working. I can hear water filling and it does drain but soap is still on the door and in the bottom of dishwasher itself. Ran diag on it and it came back clear (0). I have a Bosch SHU5315U6.


Sounds as if the pump motor has gone out in the machine. What happens is once the water reaches a certain level the machine goes into clean mode. This means the pump the forces the water into the machine isn't working. The timer actuates this pump ... Dishwashers

The unit runs through cycle fine, but ends with water remaining in the bottom, that has not been drained and dishes are covered with soap residue.


\012\012Hi,\012Here\012is a tip that I wrote that will help you with your dishwasher not\012draining problem...Dishwasher Problems - ... Whirlpool GU2400XTP Built-in Dishwasher

New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

Food odor builds up if dishes not washed daily, even though we rinse evrything thoroughly before loading dishwasher. No water remains at bottom - nothing appears to be stuck in drain. Any thoughts?


No matter how well you rinse wares, some food particles will always go into the machine. Sometimes these particles can build up and lead to what you describe. I would start by inpecting the wash tub area; remove screens, remove wash arms and clean a ... LG LDF6810 Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Hello, I have a Frigidaire Dishwasher, model FDB750RCC1. It will not fully drain. There is water in the bottom of the unit after the cycle is complete. As it is not full of water or leaking out of the unit when I open the door I am suspecting it is the pump that has broken? (the water must be draining to the overflow point and then stopping as there is nothing pumping it) Any thoughts or ideas for me anyone? Am I on the right track?


... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1927 seconds