Having problems with your GE Tritonr XL GSD6260JCC Dishwasher ?

Triton XL Dishwasher has difficulty cleaning the top rack. Water sprays in the bottom but does not seem to be as high pressure as it should be. I have taken off the water line to the top and middle rotating arms and they are clear.


Answers :

Hello stove.... Typically the dishwasher water supply is located under the kitchen sink, so it has the same (should have the same) water pressure as the hot water to your sink. Turn on the hot water into the kitchen sink and measure the water pressure there. You should have enough hot water to fill an empty one gallon milk jug in about 20 seconds. Write down how many seconds it takes to fill that jug. If it is less than 15 seconds, this will effect your dishwasher. In order to increase that flow you may have to replumb the line from the hot water tank.
\015\012
\015\012The other thing is the diswasher has a pump in it so once it fills with water the pump pushes the water through. If your dishwasher is 6 years old or older, that pump may be on it's last legs. If that is the case I recommend replacing the machine rather than replacing the pump as the cost will be about the same. Joe
\015\012
\015\012Thanks for choosing Fixya!
Repair Help & Product Troubleshooting for GE Tritonr XL GSD6260JCC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Triton XL Dishwasher has difficulty cleaning the top rack. Water sprays in the bottom but does not seem to be as high pressure as it should be. I have taken off the water line to the top and middle rotating arms and they are clear.


Hello stove.... Typically the dishwasher water supply is located under the kitchen sink, so it has the same (should have the same) water pressure as the hot water to your sink. Turn on the hot water into the kitchen sink a ... GE Tritonr XL GSD6260JCC Dishwasher

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

My kenmore m # 66515829 the water jet spinner under the top basket is not spinning to clean the dishes, I have set it in a postion closed the door let it run then open and it is in the same spot. I have taken off the spinner to make sure it is clear of debris , i see some water dripping out of the spinner but don't know if it is from other jets. Any ideas would be great.


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Kenmore Dishwashers

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

Kenmore dishwasher type 573-D, model 665.16034402. Items on top rack don't get washed. Items on bottom rack are washed fine. Appears top sprayer and maybe middle sprayer aren't getting water. At rear of washer, top rubber flapper valve (which feeds middle sprayer when top rack is in raised position) is stuck open, bottom flapper valve looks OK. We use top rack in raised position so this doesn't seem to be the problem.


... Kenmore Dishwashers

GE PDW8280 - MIDDLE ARM WILL NOT SPIN - WATER FLOWS AND SPINS FROM TOP AND BOTTOM ARMS - MIDDLE ARM HAS WATER FLOWING BUT WILL NOT SPIN. tOOK APART AND CLEANED - SPINS FREELY BY HAND BUT NOT DURING CYCLE. SUSPECT LOW WATER LEVEL? WATER IS ONLY UP TO BOTTOM OF HEATING ELEMENT


Take the whole middle spray arm assembly off -- spray arm and long tube that it is attached to. I cleaned the inside of the spray arm and found some odd stuff but it still didn't swing after the cleaning. I order all new parts and when I was repl ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Amana DWA33AW dish washer; there is no water pressure to the top spray arm. I do hear a release, water comes thru the clear tube to the top and stops! There are no glogs and there is enough water in the diswasher.


... Kenmore 24 in. 17032 Built-in Dishwasher

My chef classic dishwasher is not completely cleaning the dishes. There is no obstruction to the tablet/powder door opening, although there is a small amount of powder left at the end of the cycle. Both top & bottom spray bars are clear & rotate, the water is heating & there appears to be plenty of water getting water into the machine. Drain filters are also clear.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Magic Chef CDB6100 Built-in Dishwasher

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

Whirlpool dishwasher top spinner and top rack spinner is not putting out water or very little and not spinning. I have taken apart and cleaned everything including the sump / chopper, can't find any blockage in the tubes that deliver water from the pump to the spinners. Is the Pump or Motor done? how can that be it's less than 5 years old? Its a Whirlpool Quiet Partner I Model DU1055XTPQ3


First, confirm that the holes are not blocked on these arms. (I did not want to assume you have done this.)Then check the impeller on top of the motor stem for being loose or worn/damaged - to rule the impeller out. If it is fine, then ... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

The water is not getting up to the middle spin bar or the top one, so nothing on the top rack is getting cleaned and everything is left with soapy film, so it is not rinsing properly. There is water coming in at the side for the intial fill and from the bottom to wash.


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Bosch dishwasaher model SGS53 has stopped working and has water in the bottom of it , i have cleared this and checked the small impeller for blockages - this is ok. i have also checked the water inlet filters and the drain tube is clear . I have the top and left sid panel of and when i lift the red rod it allows watrer to come in but stops if i release the rod thr lever in the base of the machine int which the red rod fits appears th be at its lowse level and therefore the red rod cannot be p


... Dishwashers

Brand new ge GDF540HSD0SS dishwasher just installed this week has a middle arm that is not spinning. This is the one that is attached to the bottom of the top rack, and sprays water up. Water is coming out fine but no spinning. As a result, the inside of dishes on top rack are not getting clean.


... GE Dishwashers

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

Electrolux Dishwasher 24 " not enough water new fill valve new float hot water Water lines clear. water too low float never rises amd the dishwasher runs water barly covers the top of the filter straner Model FDBB2455FS0


If i was at your home as a repairman this is what i would do.if your water pressure was good at the kitchen sink,i would turn water off to dishwasher undo water connection at the fill valve,and place water line in a bucket and turn on wa ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

My KDI-21A Kitchenaid/Hobart dishwasher does not wash the top rack, but does fine on the bottom. It appears that water is not flowing to the top wash bar. Is is possible for only the top bar inlet to clog somehow? I've pulled the bar assembly itself and the main tube from the wall of the washer to the top wash bar is clear .


... Dishwashers

When I take a glass or cup out of the dish washer after they are cleaned and heat dried, or a day plus from the cabinet to put cold water,too many small bubles are floating on top the water surface, as a soap-like condition; it clears up shortly. The tech told me it is normal. I think it is not normal because I suspect the rinsing is not totally complete because of the water conservation design. Am I drinking soap-water?


Use a rinse agent., such as jet dry. the owners manual will provide you with the specific location as to where the rinse agent dispenser is locatedl ... Dishwashers

Hello, Please help. I follow recommendations for cleaning: sewer pump, cleaning arms, screens of the dishwasher. However, still machine is not working. water is not going through arms: lower, middle or top. Also, I get water into dishwater when it starts, and when I open i hear noise for water dripping into hot elements,but no water is running throughout. PLEASE HELP


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

The top sprayer is not spraying any water and the middle sprayer has water except it does not have enough pressure of water to spin around the sprayers. What do I need to do to fix the problem


All sprayed water comes from the pump located at the lower deck. Remove all parts from the lower spray assembly (note position and orientation of each part) down to the deck. There should be a large filter screen at the bottom that commonly becomes p ... Dishwashers

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

I have a Whirlpool dishwasher model number DU1055XTPQ4 that is not cleaning the dishes. When the dishwasher is working, the bottem arm is turning and water comes out the holes. The middle arm has some water coming out, but does not turn. The top arm does nothing. It appears I have a pressure problem. I took out all the arms and cleaned them, along with the plastic tube that feeds them water. They had some build up on them but not much. I have the same result as before. I took off the


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0964 seconds