Having problems with your General Electric Dishwashers ?
GE Quiet Power II (12 y.o.) dishwasher not rinsing dishes. Water flows into unit but when wash cycle begins, water drains out immediately.
\015 No problems until now. Dishes not washed at end of cycle. Tried turning off power and changing wash cycle but didn't work. Hot water flows in but drains right away during the initial wash cycle. Plastic rinse tubing and rotating arms all move freely.\015
Repair Help & Product Troubleshooting for General Electric Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
GE Quiet Power II (12 y.o.) dishwasher not rinsing dishes. Water flows into unit but when wash cycle begins, water drains out immediately.
... General Electric Dishwashers
Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa
... Kenmore Dishwashers
Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?
I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.
You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers
Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???
Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher
Frigidare dishwasher model gld355rfb2 when you select a wash cycle unit begins prewash when it moves to wash unit quits and pf (power failure )is on display unit is full of water on bottom of unit so I reset the unit hit cancel button at which time unit pumps off water . I then tried again with same results as above.
... General Electric GDWT160RSS 24 in Builtin Dishwasher
The diswasher will drain completely after the drain cycle is completed. It will then immediately begin to fill again despite no additional cycles being requested. I can hear the fill cycle begin. I can prevent the filling by opening the door slightly or by moving the float plunger up and away from the microswitch that signals to fill the bottom of the washer with water. Is there an adjustment on the float or on the length of the float plunger?
HI, The floater is not the issue here. Your problem will be with the main control assembly. The control assembly routes power to the inlet valve, and drain pump/motor. The floater is merely a regulatory ... Maytag MDB5100A Dishwasher
My kenmore diswasher model#363.153221100 when i start the wash cycle starts to fill up with water but then drains the water back out immediately and the wash cycle never starts.
Hello &\015\012Welcome to FixYa\015\012\015\012This problem\015\012is caused when the motor goes bad and needs replacement. The control will fill\015\012water and then sends signal to the motor to start a cycle, if it w ... Kenmore Dishwashers
17362 unit does not drain. When I press any wash cycle it shuts down after the wash cycle and does not drain. Can this only be the water pump or can it be something else?
Does this happen with all cycles - like the short rinse cycle as well.\015\012\015\012If this is happening only with longer cycles only then check if the water is hot when it stops.\015\012\015\012If this is happening with al ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher
Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no
Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher
My KitchenAid dishwasher (model KUD101TJWH0) suddenly is making noise from the motor area while inputing water into the unit, whether in the rinse or washing cycles but makes no noise in the draining cycles. I have pulled the unit out while still connected, cleaned any debris from the filter screen below the lower water spokes and can hear the noise very plainly by the motor but I know how sound can travel with the piping. Is the sound only coming from the electric drive motor attached to the
... KitchenAid Dishwashers
PROBLEM: Unit will start, fill with water, wait through normal cycle time, then drain. Unit does not perform washing (arms spinning & spraying water, etc.) cycle.
Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012is that the control detects that the motor is not running and so drains water\015\012directly after filling it. If you hear a hum sound from the bottom p ... Frigidaire Dishwashers
When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.
Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers
Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr
Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers
When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.
... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher
Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?
Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher
I own the Siemans SL34A006UC dishwasher which had the recall repair completed. Now it doesn't work right. The unit goes through any of the cleaning choices but when it comes time to drain, the unit stops for a few seconds, swishes water for a couple seconds, stops again, then swishes for a couple seconds, stops and then goes back in to regular cleaning mode until the timer reaches zero. At each drain cycle, it does the same thing earlier mentioned 3 times in a row, then back to washing. The unit
You say "dishwasher which had the recall repair completed." (sic) "Now it doesn't work right" (sic)\015\012\015\012Being a professional I must advise,and that, if this is the case, th ... Dishwashers
I have a Bosch SHE55C05UC dishwasher and it just started to not wash properly and leave water in the pan below (first time it did not drain at all.. I tried the rinse/hold cycle and got the unit to drain and tried again and it is not working properly and keeps water in the pan. I am on a well and have great water pressure about 70 psi.
I am assuming you have checked the filter and drain sump and there are no obstructions. Have you tried taking the drain pipe out of the sink downpipe and checking if it drains directly into the sink?\015\012\015\012I am also assuming the ... Bosch SHE55C05UC Dishwasher
My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This
By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher
Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella
Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher
All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.
Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers
There is a pool at the bootom of my dishwasher when the wash cycle is completed. When doing "Rinse Only", I could hear something come on immediately following the rinse but nothing seemed to happen. I pulled the Dishwasher out and the drain tube is set up so that it immediately goes upward a few feet before it eventualy goes back down to the drain. I noticed that there is water in the tube right next to the Dishwasher before it makes that climb. I'm wondering what all this means...
Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012 ... GE GLD5800L Dishwasher
Dishwasher is not running thru cycles properly. During wash or rinse cycles, dishwasher fills up with water, then immediately drains water back out.
HI, your control board/timer is faulty and it will need to be replaced. the logic chip has failed. ... GE Dishwashers
Control Module? I have a GE Profile that seems to have a control module issue. I've changed the module and it continues to do the same thing...won't drain at end of cycle and begins washing right away after selecting new cycle. Washes for only about 5 minutes total and then just heats the water...soap dispenser doesn't get rinsed clean either. Any ideas?
... GE 24 in. PDW9880LSS Stainless Steel Built-in Dishwasher
I have an Asko DW1875 dishwasher (10yrs old) which has just recently started having problems. The initial symptom was that during a washing cycle, unit showed '1' and inside became very hot (melting some plastic cups/plates in unit). On further investigation (with diagnostic mode), the dishwasher is filling and draining with no problem. When circulation pump runs there is barely any water pressure in blades (just dribbles out) and water leaks into undertray via a plastic white tab near front (v
... Asko D1876 Dishwasher