Having problems with your General Electric Spacemaker® GSM1800N Built-in Dishwasher ?

My wife opened the Dishwasher in the middle of a cycle and turned the cycle to off. Dishwasher will not turn on. Power is ok. Bottom of Dishwasher is full of water. How can we get the dishwasher to restart?


Answers :

Repair Help & Product Troubleshooting for General Electric Spacemaker® GSM1800N Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My wife opened the Dishwasher in the middle of a cycle and turned the cycle to off. Dishwasher will not turn on. Power is ok. Bottom of Dishwasher is full of water. How can we get the dishwasher to restart?


... General Electric Spacemaker® GSM1800N Built-in Dishwasher

Hi, My dishwasher keeps stopping mid cycle and the door pops open. The soapy water is always gathered in the bottom and there's no way for me to get rid of the water, unless i restart the full cycle. The dishes are all getting stained with white marks, even though the salt and rinse aid is filled. Please help!


Sounds like the latch is worn out you mabe able to get a new one at appliancezone.com.... also check the drain for debris ... Baumatic 23 in. BDW9 Built-in Dishwasher

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??


You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

I have a G E Nautilus dishwasher that has been in storage for 2 years. Every thing works but the Drain. When the cycles are finished I' m left with a dishwasher full of water and it dont drain. I checked the bottom as u said in a previos question I see not obstacles, trash etc. How else4 can I get it to unplug? Also where can I get a owners manual? I can be contacted at [email protected]aol.com if needed. Thanks ahead of time for the help.


Hello. Here is the link to a free manual http://kitchen.manualsonline.com/manuals/mfg/ge_appliances/ge_ap ... Dishwashers

Dishwasher restart Please help! I started a cycle and about 1 hour later I went to check and it was no longer working- no power at all. There is water at the bottom inside but I can't make it drain. This happened once before and the technician people gave me a way to restart the dishwasher by pressing certain buttons - I can't remember which ones. Does anyone know??? I need help!!


I don't know about a button sequence but I would suggest that you turn off your breaker and then back on. That will reset most electronics. ... Kenmore 15129 Built-in Dishwasher

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

I have a Bosch Dishwasher- I installed a new garbage disposal and forgot to knock out the drain plug (dumb-i know) and I ran the dishwasher that night- well in the morning I noticed it was full of water and the bottom and the drain was humming. I then realized what I had done- so I knocked out the plug and the dishwasher drained immediately. but now the drain continues to run - even with the door open and I cannot get it off the drain cycle. Any suggestions?


\015\012If you notice still any water in the base. you sponge out the water and then check turning ON the dishwasher. If still the same problem then two possibilities \015\0121) bad water fill value. ... Dishwashers

Dishwasher has stopped during programme - door may have been opened during cycle??!! - although cycle had only just started. bottom of washer has water in but cant seem to restart on ANY programme - pls help!!! have turned off at power and back on etc - no joy :(


... AEG 24 in. Favorit 80860iW Built-in Dishwasher

My dishwasher stopped in the middle of a cycle and is full of water. Breaker is good and power is at dishwasher but will not restart and no lights will go on when buttons pressed? Any ideas?


I replaced a thermal fuse located under the control panel. A power surge likely the cause due to a storm passing thru town. ... Kenmore Dishwashers

Hi, Had a power cut at my home and my Caple Di455DL Dishwasher was mid cycle on a glasswash program at the time, since power has been regained it will not restart or reset itself, it just lets a pulse of four beeps go once the door is shut and makes a sounds like its trying to pump out water? tried turning off at mains etc but cant get it to reset!


... Dishwashers

Whirlpool dishwasher, model DU1050XTPQ1, type 575-0; problem: showing no sign of power to unit and bottom of dishwasher is full of water---it apparently stopped during cycle. Is there a reset button? I have tried depressing the front panel "lock" button for five to ten seconds to unlock the system with no luck. The washer is hard wired to the home electrical system. What should be my next course of action? Thanks


... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Frigidare dishwasher model gld355rfb2 when you select a wash cycle unit begins prewash when it moves to wash unit quits and pf (power failure )is on display unit is full of water on bottom of unit so I reset the unit hit cancel button at which time unit pumps off water . I then tried again with same results as above.


... General Electric GDWT160RSS 24 in Builtin Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

My dishwasher quit running in the middle of it cycle like there is no power going to it..... there is water standing in the bottom of it and i cant get the washer to come on or anything.... could it be something simple????


It is simple to repair. you need a thermal fuse. take the control panel off and right where the control board is you will see the thermal fuse. you can either replace it or just splice the wires. let me know if you need further help ... Kenmore 18 in. 14432 / 14439 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2472 seconds