Having problems with your General Electric WD18X215 SUMP INLET ?

How to replace WD18X215 - General Electric WD18X215 SUMP INLET


Answers :

Repair Help & Product Troubleshooting for General Electric WD18X215 SUMP INLET

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace WD18X215 - General Electric WD18X215 SUMP INLET


... General Electric WD18X215 SUMP INLET

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

Manitowoc SDO45 2a water not going into sump pan. Stops at water inlet vlave. Should I just replace the valve


... Dishwashers

Replacing a dishwasher door cable - GE Dishwasher Repair Part - General Electric Door Cable WD7X14


... GE Dishwasher Repair Part - General Electric Door Cable WD7X14

How to replace WD22X124 - General Electric WD22X124 PWR TWR ASM


... General Electric WD22X124 PWR TWR ASM

How to replace the sump inlet of a GE portable dishwasher GSC3507P00WW


... GE Portable Dishwasher

Replace ge 640L door cable WD7X14 - Maytag 2190-0001 Dishwasher Repair Part - General Electric Door Cable WD7X14


... Maytag 2190-0001 Dishwasher Repair Part - General Electric Door Cable WD7X14

I have a Bosch SGS66E02GB/45 that no longer completes a wash cycle. On "Auto 50C" time counts down from 2:58 to about 1:40 then goes back to the beginnnig and repeats. Spray arms are moving, it fills and drains, detergent is dispensed. I have checked the inlet and outlet pipes, the impellor and non-return-valve in the sump, checked the matrix is clear, checked to anti-flood float and switch and replaced the relays on the PCB. Selecting a rinse cycle will complete. Dishes are warm and wet rather


... Bosch Dishwashers

Getting error code 1E I've replaced the sump pump, cleaned the screen at the water inlet, checked water flow from the hose. Continue to get the 1E once water has entered dishwasher and begins the wash cycle.


... LG 24 in. LDS 5811 Built-in Dishwasher

LE on display panel. I have taken front panel off and all wiring has already been electrically taped together, so I don't think it is wiring. (This was done by a service rep when I had 1E problem) How do I tell if the impeller, rotor or blade is blocked? Or sump assembly or main power control board needs to be replaced?


Http://www.justanswer.com/questions/2bijk-i-have-a-lg-ldf6810st-dishwasher-with-an-error-that-the-serv ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I am replacing a frigidaire dishwasher washmotor. Everyone and videos tell me how to replace the motor. In the instructions in the box they say replace the sump bottom also. Why would i have to replace the sump also and not just the new motor?


Hello, chris\012 \012 I was trying to help\012 you out here. I was going back to some customers that asked questions \012in the past and it appeared that no one answered them, so I thought I \012would take some ... Amana ADB1400AWB Dishwashers

I have a 5 year old GE Dishwasher Model Number PDW9880JSS which needs to be replaced. What type of electrical connection does this unit have? Is it a standard USA plug type or does this unit require hard wiring? Reason I ask: I want to replace with a dishwasher using the same electrical connection type.


Hi\015\012\015\012Electrical connection is on right side of dishwasher. This dishwasher should have a 3-prong grounding type receptacle in the rear wall of sink cabinet next to the dishwasher. The receptacle should be installed at least 6 ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Where does it go - General Electric WD15X10003 GENERAL ELECTRIC WD15X10003 WATER VALVE


Click on : tips ... General Electric WD15X10003 GENERAL ELECTRIC WD15X10003 WATER VALVE

Model: 1578201D PSI 4000 3.5 GPM The machine is only 2-3 years old and has always worked fantastically (with very limited usage). The inlet fitting got broken and we replaced it with a new inlet filter (part number 35169) and now it has low pressure. Is there something else we should check or replace?


Hi there,A "chattering" pressure washer pump can be caused by many things. You could have a bent or damaged inlet line, or the water supply might be too low. Fixing these is simple, but checking on the water supply is critical. Never let ... Pressure Washers

Samsung dmt800 dishwasher error code 4e. Water valve is open, pressure and temp correct, flex water hose not kinked, water inlet valve is free of debris. next steps? replace water inlet valve?


... Samsung DMT800RHW Built In Dishwashers

Where can I purchase new spray arm for general electric dishwasher


... Maytag Dishwasher

I had to clean out the chopper and clean out the screen. I had to clean it all out and the seal to the sump got broken. do i have to replace the sump(parts.com) says sump with seal. you cant buy just the seal. Is there anything i can do to stop it from leaking around the seal?


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Attempting to install asko d1706 dishwasher. Bought used, had no hoses with it. when trying to connect water inlet hose, unable to connect without leaking. Finally got a connection on there that has it slowed down to a drip. does the inlet valve need to be replaced or is there a special inlet hose that we don't have?


Yes there are actual dishwasher supply hoses you can purchase at most hardware stores.... if you do have the correct hose may try to put some teflon tape on connection so that leak stops....\012good luck to you ... Asko Dishwashers

Kitchenai Dishwasher Replacement of "Inlet Air" (lower door seal)


... KitchenAid Dishwashers

Bosch SHY66C makes groaning noise during the wash cycle. Circulating pump, drain pump and water inlet valve have been replaced.


... Bosch 24 in. SHY66C02 / SHY66C06 Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

My defy dishmaid dishwasher isnt letting in water. I have replaced the pc board and the inlet valve and the salt bucket all to no avail. The inlet valve is not getting power from the pc board.


... Dishwashers

Can I replace the inlet valve with a different inlet valve than original. I have a 3378779 I want to use a whirlpool valve I found on line for $17.


You need to make sure the coil voltage is correct, the threaded connections are the same thread, the threaded connections are properly oriented, and the new valve will fit into the space of the old valve, or you'll spend more time making it work than ... Whirlpool 24 in. GU980SCG Built-in Dishwasher

Leaking FDW60 I have a Hotpoint FDW60 dishwasher. yesterday it tripped our house electrics and then we had water flooding out of the dishwasher. Through a process of elimination I have now discovered that water is leaking from the drainage sump in the centre of the babse down onto the motor or other electrics. I have looked for loose hoses and there are none visible from the base of the dishwasher, can you give some ideas where the water might be coming from?


Had a similar problem when I removed the lower spray arm for replacement (see http://www.fixya.com/support/t234402-fdw60_dishwasher ) and didn't put the centre retai ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0821 seconds