Having problems with your Haier Dishwashers ?

My dishwasher has decided to trip the safety switch on the house when it changes cycles the motors running but nothing is happening


Answers :

Hi :

It seems that your dishwasher is old one . You need to replace the shaft or the fins .

good luck
Repair Help & Product Troubleshooting for Haier Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher has decided to trip the safety switch on the house when it changes cycles the motors running but nothing is happening


Hi : It seems that your dishwasher is old one . You need to replace the shaft or the fins . good luck ... Haier Dishwashers

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat


... Asko Dishwashers

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Motor running, nothing happening!


... Bosch 24 in. SHU5305UC Built-in Dishwasher

My Maytag Performa model # PDB3600AWE is not draining. When it gets to the 2nd half of the rinse cycle, nothing happens, no noise, nothing. Could this be a problem with the motor? It seems to run fine through the wash and rinse cycles.


... Maytag PDB3600A Built-in Dishwasher

The motor continues to run with the diswasher powered off. In addition it will no longer enter wash mode. It can be powered on and wash mode can be selected, but nothing happens except the motor continues to run. Cycling the power feed off and back on does not solve the problem.


Hello John,\015\012\015\012The simple answer (without looking at the wiring diagram) is the float switch. The simple answer (after looking at the wiring diagram) is the float switch. I've posted the wiring diagram for this washer to Flick ... LG 24 in. LDS 5811 Built-in Dishwasher

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

After 3 years it just started making a loud noise, I am no expert but it sounds like a fan in a motor. I have only heard it today, but I am betting it will still happen next load too. I didn't change any of the settings, have been running the same way forever. When I did hear this noise I started pushing buttons to see if I could get it to stop, no good, no change. The cycle has completed and everything looks ok, waiting on the dishes to dry. Drainage has never been a problem for me either.


I would say this is a build up of lime.try changing your tablets and checking your salt levels.there is no fan .try what i say and see what happens.have you found a glass broken it could be as simple as that but i dont think its serious.adrian,,,, ... GE Nautilus 24" Built-in Dishwasher

Kenmore 665.16529000 When we put the dial to pots and pans the diswasher fills up and cycles through, when the dials moves to normal wash, it fills up and cycles through again. When the dial gets to light wsh we can hear the motor running but nothing is happening, but the soap door opens soon after. The heating light comes on and the inside of the dishwasher gets so hot that it has melted our big plastic tumbler cups on the top rack and makes the counter top extremely hot to the touch. The dial


... Dishwashers

Asko D1996 Dishwasher - Tank fills with water but it "washing" cycle never starts. However, the heating element begins the work and with no water running over the heating element it smells like something is burning. I have tried changing the programs from Pots and Pans to regular wash but the same results. Nothing happens


... Asko D1776 Stainless Steel Built-in Dishwasher

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

My dishwasher will not drain. When I try to run it through the drain cycle by hitting drain/cancel button it makes one click and nothing happens. I checked for blockages in the drain line and valve but the motor just wont start.


Check to determine if the pump out motor is functional by checking if supply voltage is across the 2 terminals in pump out mode with a AC voltage meter. If voltage is present and motor does not spin this is an indication that the motor is open circui ... Dishwashers

Bosch SHE43M was running when a pipe broke under the sink and flooded the kitchen. Water turned off before dishwasher. Now dishwasher makes a motor sound but no water starts and no cycles. Nothing happens when pushing buttons 3 & 5 to reset


Water is in the base and the float switch is activated. you must remove the water to deactivate.then hit the drain and cancell. let me tell you a quick joke .Im a old bosch tech and i had a call with the same problem. as soon as i got there i notice ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Can hear motor running but nothing happens in dishwasher


Hi, you need to test voltage to the water inlet valve. If you are getting voltage (120V) replace the valve. If you are not getting voltage check the water level switch located in the front corner of the tub.\015\012If I can assist you any furt ... Dishwashers

Both drawers of dishwasher have the motor running but nothing happens. I turn them off and they turn back on.


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

Won't start After two months of no use my dishwasher won't work. I can hear motor running but no water. We tried cleaning by filling with water (priming motor) but nothing happens. Now the dishwasher if full with water, motor makes noise but nothing is happening. Help!!


It sounds like you have a food blockage or some blockage between where the water fills up and where it goes into the pump you need to take out the water wand (the rotating thing with water coming out) only the bottom one. You need to unscrew the wate ... Hotpoint 24 in. HDA1000Z Built-in Dishwasher

Nothing happens when the dishwasher is turned on for any cycle... the timer starts and keeps going but the motor - pump don't kick in... the time for the cycle expires and nothing has happened.


1.Listen for a humming sound.\015\0122. faulty motor, start relay. ... Frigidaire PLD2855RFC Dishwasher

The water is pumped out after the rinse cycle then it continues to run and make an unusual noise but nothing happens. The noise is almost a grinding sound. There is also a smell like some part may be hot or the wiring may be hot. I can reset the dishwasher and re-run the cycle up until that same point and it does the same thing again. I have had a repairman out twice in the last six months. The first time he could find nothing wrong because the problem was intermittent and he couldn't see anythi


Timer \015\012\015\012or\015\012\015\012 ... Bosch Dishwashers

How do I reset a KitchenAid Whisper Quiet Plus? Right now, if I try to initiate a heavy cycle (or normal cycle, or whatever) all that happens is the cancel light lights up and the dishwasher makes a moaning noise. If I let this run its course, nothing happens (i.e., after the moaning stops and the cancel light is no longer on, if I try to initiate a cycle, the same thing happens all over again).


... KitchenAid Dishwashers

Hotpoint, intergrated dishwasher BF12/47916/7 has stopped working, There is nothing happening at all. it has done half a cycle the only thing that happens is when you put the cycle on the dot before cycle no: 2 the power light comes on orange, this usually goes red when the cycle is on. I have changed the fuse & there is no difference. Help!


... Hotpoint 23 in. BF41 Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.


... Maytag MDB7100AWB Dishwasher

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1199 seconds