Having problems with your Haier ESD210 / ESD211 Built-in Dishwasher ?

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


Answers :

Repair Help & Product Troubleshooting for Haier ESD210 / ESD211 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Dishwasher HED6612 - salt light came on - have now filled the salt up and light has gone off. since this has happened whatever programme I set it to once the pre-rinse has finished and the wash light comes on an alarm sounds and doesn;t finish the cycle. when the alarm sounded I have pressed the start/reset button for 10 seconds to see if it resets it. I requested a manual last week and not received a reply from yourselves. this machine is around a year old [no manual available] and has been


... Hoover HD95M Free-standing Dishwasher

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers

I have a zanussi tempoline dishwasher, I have loaded this as I usually do, turn the knob to the right and select the 2nd programme the light next to this comes on, I have pressed this to start the machine although it seems as if it is going to start this light flashes and the top arrow on the right of this flashes intermitanly, but the machine does not start the wash programme. The 3hr delay button if I had pressed this by mistake which I am sure I have not would light up. When I found it did no


Hi Ruth.The machine can be in error mode. In this case one or more lights in the control pad will stay on or flash and the cycle will not start.One of the most common fault in your situation, and at start of the cycle is no wa ... Zanussi Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

I just installed a brand new Haier ESD210 Dishwasher. When i press the Power button, the lights above the Normal Wash and Light Wash buttons flash and it beeps. Any ideas on what to look for? Thanks.


... Haier ESD210 / ESD211 Built-in Dishwasher

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Rotary switch selection of washing program.Whichever one selected - machine sounds to start up, whether or not the start button is pressed. However no sound of washing kicks in as was usual and eventually the light over the start button starts blinking and all noise ceases - blinking continues.


Found a local man on the internet, who popped in and leant the machine forward then backwards and then flushed out the system, explaining that the program cycle had gone awry and there was water where there should have been air and so microswitches h ... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Maytag Quiet Series 800 dishwasher won't start. The only button that I can get to work is pressing and holding the locking feature--that light eventually comes on. A couple of times I came back in an hour or so or the next morning and hit the start button and it started right up. Now it won't start at all. VERY FRUSTRATING!


... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a kitchenaid dishwasher, model# kuds01flss1 and the cancel light flashes constantly but the machine won't respond. when i press the normal wash button it also flashes along with the cancel button but no response


... KitchenAid Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

When I press the on button on my Hoover dishwasher HF1 3015 all the lights come on at once and the machine beeps continuously. Any idea what's up?


... Hoover Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1254 seconds