Having problems with your Haier ESD310 24 in. Dishwasher ?

Our ESD310 has a message of OP on the screen. It will come on and run on its own if the door is shut, counting down from 2. When I can get it to turn on and start a cycle it runs a bit, skips a bunch of time, runs a little more, and then skips time again counting down from 2. The high temp wash button will light up on it's own while running. The cancel button does not work. It acts as if it has a short, makes funny noises, and I'm afraid it's going to catch on fire.


Answers :

Repair Help & Product Troubleshooting for Haier ESD310 24 in. Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our ESD310 has a message of OP on the screen. It will come on and run on its own if the door is shut, counting down from 2. When I can get it to turn on and start a cycle it runs a bit, skips a bunch of time, runs a little more, and then skips time again counting down from 2. The high temp wash button will light up on it's own while running. The cancel button does not work. It acts as if it has a short, makes funny noises, and I'm afraid it's going to catch on fire.


... Haier ESD310 24 in. Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

I have a Kenmore Quietguard Standard model 587 Dishwasher. It's about 3 years old. Lately, it has been running fine through the first hour and then towards the end, it will pause and the "Hi Temp" and "Heat Dry" like will start blinking at the same time. It's like it is stalled. When this happens, I open up the door and look at the bottom of the dishwasher were the screen is, and I see there is standing water. I press the "Start/Cancel" button to help it drain all the way, which it does, but th


Hi,My take on that would be a bad heating element....the dishwasher is looking for the heat from it and that never happens....so it goes no further and gives the alarm....I would get someone to check that heating element out and replace i ... Kenmore Dishwashers

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

8 years ago we bought a model 665 Kenmore Limited edition Stock #575-0 if you need that. A certified kenmore tech. has been out here 3 times with still no clear answer. The problem is when you run a standard cycle of 95 minutes it counts down to 78 minutes and stays at that time for about 45 minutes then stars counting down again till 42 minutes then stops at that time for about another 45 minutes then coutinues till it finishes the wash and drying cycle. It runs and sounds fine the entire time


Sounds like timer prob.would rec. replacing timer ... Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Start button keeps flashing machine will not run on any program. I've tried holding down the start and time button which in the past has allowed me to restart the machine. This isn't working this time


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.


... Maytag MDB7100AWB Dishwasher

I've tried to use this new machine 3 times. Each time it was never turned off until I pushed the cancel/drain button. Once I let it run for 2 hours before turning it off. This evening I tried the rinse only button and when I checked on it,it had switched to the normal wash cycle. Then I pushed the cancel/drain button.


If this is a new machine and it's under warranty, Have a technician come out and repair it as soon as possible. then fully test it's operation after he is done fixing it . It sounds to me as though it ... Whirlpool Gold GU2275XTV Builtin Dishwasher

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

My Whirlpool ADP 5406 runs for about a minute and then the light flashes four times, repeatedly. What can I do to fix this? (I can still get the machine to run its cycle by holding down the start button, but the light will flash four times again on completion).


Hi and welcome to FixYa. I am Kelly. \012 Usually this symptom also shows an F7 error code. You will need to remove the lower wash arm (NOTE INSTALLED POSITION) Also you will need to remove the metal grate under the wash arm to ... Dishwashers

My Whirlpool Gold Quiet Partner III was DOA when I went to use it today. I unplugged/plugged it back in, at which time the "China Crystal" LED flashed a sequence of 3 flashes, then 3 more flashes, pause, 3 + 3 more, pause, 3+3 more, pause, etc., etc. And it would not run on any other cycle, but it did seem to run thru that one OK. Upon completion of the cycle, it was DOA again. Did the "Normal/Air Dry/Normal" button sequence, and now the Rinse Only button is steadily flashing. Any suggestions? I


When the rinse light is flashing steadily then the reset procedure for your model is pressing the "Normal/Air Dry/Normal" buttons.\015\012\015\012If it did not reset your dishwasher the control board must have fa ... Whirlpool GU2400XTP Built-in Dishwasher

WE HAVE A MAYTAG PLUS DISHWASHER ABOUT 3 YEARS OLD OR LESS. WE WERE GETTING READY TO WASH A LOAD OF DISHES AND THE LOCK BUTTON IS ON AND WILL NOT COME OFF, WE HAVE TRIED PUSHING THE DRAIN OFF BUTTON BUT IT WILL ONLY BLINK, WASHER WILL NOT RUN. LOCK BUTTON WILL BLINK 3 TIMES AND STOP WHAT DO WE DO?


Try holding down the drain button for about 5 seconds.If that still does not do it for you, try taking power from the machine to let it reset itself, easiest is to unplug the unit or flip the breaker switch for the section of the kitchen. ... Dishwashers

Start button flashes green but does not turn on. cancel button works for 2 minutes ( sounds like it is trying to drain) then shuts off. still can run the dishwasher. if I press any other button, such as pots and pans, the "time remaining" just has 2 lines. then it just repeats as above.


Most likely you have answered your question already... the drain pump is either obstructed or has failed... these units these days have plastic impellers inside and often go bad causing the drain motor to go bad... if the unit does not drain it will ... Whirlpool Dishwashers

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

My Frigidaire model FDBB2040FC3 "acts" like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it "running" or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns. We're a family of 6 so our dishwasher is pretty important in this hou


... Frigidaire Dishwashers

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d


The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers

My brandt VF300 doesn't drain at the end of wash cycles. If you run the soak programme it drains fine. Some time ago the door was adjusted by an engineer, when he arrived he pressed some buttons which then drained the unit immediately, I have forgotten which buttons! Is there anything I can do to reset the thing, given it drains on soak I am doubtful the drain pump has broken ir is blocked?


... Dishwashers

I have a kitchenaid dishwasher, SS, model # KUDIO1ILBL6. When you press the ''normal'' button to run it, nothing happens. Tried other cycles and same thing, the green light goes on above the cycle but its just not starting. I tried resetting by opening, pressing high temp scrub then energy saver dry, high temp scrub, energy save dry, then close and hit cancel. Is there any other combo to reset it? or does it sound like something else is wrong? thanks!


... KitchenAid Dishwashers

I set my dishwasher to pots and pans to run a dishwasher cleaner, and now when I push the auto button, the time reads 2hrs. instead of the 93 mins. it always read before. How do I reset the auto button to the way it came?


... Maytag MDB7100AWB Dishwasher

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1237 seconds