Having problems with your Haier ESD311 24 in. Built-in Dishwasher ?

I RECENTLY REPLACED MY WATER HEATER AND THE DISHWASHER MAY HAVE BEEN ON WHEN THE WATER SUPPLY WAS TURNED OFF.NOW MY DISHWASER WON'T START. THERE'S NO POWER TO THE DIGITAL KEYBOARD AT ALL. IS THERE A FUSE OR RESET BUTTON TO CHECK?


Answers :

Repair Help & Product Troubleshooting for Haier ESD311 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I RECENTLY REPLACED MY WATER HEATER AND THE DISHWASHER MAY HAVE BEEN ON WHEN THE WATER SUPPLY WAS TURNED OFF.NOW MY DISHWASER WON'T START. THERE'S NO POWER TO THE DIGITAL KEYBOARD AT ALL. IS THERE A FUSE OR RESET BUTTON TO CHECK?


... Haier ESD311 24 in. Built-in Dishwasher

My Samsung DMR77LHS dishwasher has lost power completely near the end of a cycle. About an inch of water remains. I have power to the unit. I checked the 15 amp fuse in the unit - it had blown. I replaced it, but still no luck. The fuse is not blowing, but there is no power to panel. Nothing happens when you hit the power button - no lights or anything. Unit acts as if ther is no power at all. I have seen similar posts. Any thoughts?


Hi, whenever a fuse of that magnitude, or any fuse really, Blows, you should never just replace it, as to have any device, blow a fuse, trip a breaker, requires a major fault, they do NOT blow spontaneously ever. So you have had a major short circu ... Samsung DMR77LHS Tall Tub Dishwasher

Kenmore dishwasher... filled up with water and its lights went off.. no buttons work acts like no power. check the house fuse box - ok ... check the 2 door switch - ok .. checked the thermal fuse - ok ... so, i picked up a new board and changed it out. still wouldn't run.


Did you check power to the unit? Double check the common and grounds. When servicing I will disconect(unplug from wall) power to the unit. Is it pluged in? Use another outlet(the outlet under the sink may be wired thru a switch for a disposer)even ... Kenmore 24 in. 16032 Built-in Dishwasher

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

My dishwasher has no power not even on the touch panel leds lights. I checked the connections.. Is there a reset button or a fuse i can replace or reset?


Several possible problems:\015\0121. door switch failed. Expose it and test\015\0122. Neutral connection loose at junction box under dishwasher. Expose and test.\015\0123. Control board or Touch pad failure. Expensive to replace. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

I cannot get this unit to power on....I checked the breaker and even replaced the 20amp fuse in the box.....Is there a reset button?.Where is it?...........model FDB2810LDC1


Hi\015\012\015\012To reset the control press and hold the AIR DRY/RINSE\015\012ONLY/HEATED DRY button for 15 seconds, if it wont work then the control board\015\012should be replaced. Hope this helps...please post back for further assista ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Indicator lights on Maytag dw model mdbh 955 do not light up. Plugged into live plug. Door is engaged and clicked shut. It's like there is no power to the unit but there is. Is there a reset button I need to check or a fuse?


Hi,Follow the steps :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwasher? This can be difficult to test,\015\012because dishwashers are usually wi ... Maytag 24 in. MDBH955AW Built-in Dishwasher

I have a GE Max,mod # GSD6610G00SB....it worked fine a few days ago,today theres no power to it,Any suggestions?I've already tried holding in the reset button and checked the breaker with no luck and can't find the papers!


... GE Nautilus 24" Built-in Dishwasher

Campbell hausfeld standard duty electric pressuse washer serial 15930 water wizard .. I cannot locate the reset button and after a short while it wont turn on at all it powers off automatically. and after checking cords and plugs it wont turn on at all..


... Campbell Hausfeld 1,350 Psi Electric Pressure Washer With Auto Detail Kit #PW1350

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

My du943 dishwasher will not power on....it looks like it lost power after the dishes were washed and before the water drained. The fuse is not blown, the power box underneath the unit appears ok, and I checked the thermal fuse after reading other posts with the same problem. What to do from here?


... Whirlpool 24 in. DU930PWP Built-in Dishwasher

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

No power unit went dead checked power to base of unit ok also shut off breaker for 10 minutes to see if it will reset, no luck. Also removed inner door panel to reveal circut board to look for a reset or small fuse, none evident.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher

Hello, my Siemens integrated dishwasher no: SE64M359GB stopped working mid-cycle with 35mins remaining. It is displaying the red tap emblem. Usually the dishwasher starts when the dishwasher door is closed fully (having pressed the power button). However, it is making a noise as soon as the power button is pressed. I have checked the water supply and pipes and they are OK. The filters are also clean and OK. We have an electric de-scaler on our system so I imagine calcium build up should n


... Siemens Dishwashers

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

Ge gld5800 water supply and power good, but water does not enter. Buttons for Normal Wash and Heated Dry flash on and off. Have disconnected power and reconnected to "reset" to no avail.


2 things to check, the water inlet solenoid valve which activates and allows the water to enter the machine and also check the door switch/lock mechanism, if the board doesn't think the door is closed properly it will not respond. hope this helps. ... GE GLD5800L Dishwasher

Hello everybody, I hope that you gona a give me some tips for repairing my dishwasher mashine. A few days ago, the error F2 appears on my dishwasher machine (Baucknecht GSI 5894) I checked the pump for the waste water is ok. the tap water is not taking in,I checked the hoses they are ok as well I turned off and on and same time pressed the button reset and choosing the programm on the dishwasher few seconds trying to start and again apperas F2 . Hopefully someone can help me. Best regard


Possible the inlet valve has given up and is not allowing water in.\012Also possible there is a slight leak enough to shut the water off (safety feature) - Check underneath for a float mechanism and any water there. ... Bauknecht Dishwashers

Where is the reset button on a ge dishwasher ? GE dishwasher won't start up no power is getting to the machine..checked breaker and plug in all ok is there a reset button located anywhere ?


... GE 24 in. GSD2000Z Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1944 seconds