Having problems with your Haier ESD311 24 in. Built-in Dishwasher ?

RECENTLY REPLACED WATER HEATER, THE DISHWASHER MAY HAVE BEEN ON WHILE THE WATER SUPPLY WAS SHUT OFF. NOW THERE IS NO POWER AT ALL TO THE DIGITAL KEYBOARD.


Answers :

Hello Suzy. If the dishwasher was operating and then the water supply was shut off, a number of things could have happened. Since you have no power at all, you should begin by going to your electrical panel for the residence and resetting the circuit breaker or replacing the fuse which sends power to the dish washer. Once you do that, go ahead and try starting up the dishwasher again. If it operates properly, excellent, if not, I recommend having a repair person check it out. Good luck with it. Joe
Hi, well it is unlikely that the absence of water would cause any problem.at all. I would say, what has happened, is when the Power was Turned OFF, to replace the Water Heater Element. When the Power was reconnected to the "Grid" Via the main breaker, The "Inrush Current", to the Dishwasher would have, indeed, probably destroyed it.. You see when you connect the Mains back on to a "System", ALL devices need to be completely, DISCONNECTED, (Plug Withdrawn). from the Mains, Simply Turning OFF is NOT sufficient, to prevent all damage. Anything other than a pure "resistive load", will most likely be destroyed, with the reconnection of the main power again, to the "Grid". As, immediately it causes, transients, spikes, surges, and overvoltage transients, these exist for a few seconds/minutes, or more, after reconnection, these can and do destroy delicate electronics..In my experience, I suspect this is actually what has happened. \015\012You could try turning OFF and taking plug out from wall. leave out for 5 mins or so, reconnect and turn ON. If this doesn't resurrect it. Then I am sure, the Controller has been spiked, and you will either need to repair this yourself, or get a professional service person.
Repair Help & Product Troubleshooting for Haier ESD311 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

RECENTLY REPLACED WATER HEATER, THE DISHWASHER MAY HAVE BEEN ON WHILE THE WATER SUPPLY WAS SHUT OFF. NOW THERE IS NO POWER AT ALL TO THE DIGITAL KEYBOARD.


Hello Suzy. If the dishwasher was operating and then the water supply was shut off, a number of things could have happened. Since you have no power at all, you should begin by going to your electrical panel for the residence and resetting the circu ... Haier ESD311 24 in. Built-in Dishwasher

I RECENTLY REPLACED MY WATER HEATER AND THE DISHWASHER MAY HAVE BEEN ON WHEN THE WATER SUPPLY WAS TURNED OFF.NOW MY DISHWASER WON'T START. THERE'S NO POWER TO THE DIGITAL KEYBOARD AT ALL. IS THERE A FUSE OR RESET BUTTON TO CHECK?


... Haier ESD311 24 in. Built-in Dishwasher

Model 818s stops mid cycle and beeps continuously. water not drained out. water on floor. no lights on. shut power off and leave 1 hr. turn power back on and still beeping


... Fisher and Paykel Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t


The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

Bosch #SHE44C dishwasher does not fill. No power to the water solenoid, but power coming out of the control board and the emergency shut off float and switch is working. I need a manual with a wiring schematic and cycle sequence so I don't have to tear it completely apart to trace every wire. Thanks


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Water pump keeps runing even when i open the door. and there is no water in it. i have to shut of the dishwasher with the power switch on the inside top left of the door. its 6 years old the model # is DFUD 140


Hello,Welcome to FixYa.Based on your description "water pump keeps running even ... Viking 24 in. Professional Series DFUD140 (Premium) Built-in Dishwasher

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

My kenmore dishwasher model 665.16364300 has no power. The breaker did not shut off. The water heater breaker did shut off. What should i look for.


... Kenmore 24 in. 16362 / 16364 / 16369 Built-in Dishwasher

Kenmore we have a kenmore 665.1376 that is just over a year old. last night after about 15-30 min it shut down. there is water standing in the bottom but i don't think the float shut it off. checked the power breaker and everything seems fine there.


... Kenmore 15073 Stainless Steel Built-in Dishwasher

Hi, Had a power cut at my home and my Caple Di455DL Dishwasher was mid cycle on a glasswash program at the time, since power has been regained it will not restart or reset itself, it just lets a pulse of four beeps go once the door is shut and makes a sounds like its trying to pump out water? tried turning off at mains etc but cant get it to reset!


... Dishwashers

Hi, the Council shut the water off to our house then when the water was turned back on I put the Whirlpool dishwasher on and now every time I try to use the dishwasher it cuts the power to the house. Will i need to get a technician out to look at this problem?


Hello - Probably, but someone with basic electrical skills can check the wires in the power connection box under the unit. If these wires look good, the problem is best left to a pro. Some part of the circuit is grounding, causing breaker to trip. Fi ... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

When the dishwasher not in use, it filled the water up by itself. And after it was full, the water leaked out to the floor. Even after I turned off power, it cannot stop. I have to shut the valve under the sink to stop it. What is wrong? It is only three years old. Hou


Hi,\012If you have a problem with your washeror dishwasher continuing to fillwith water after the valve has closed, then you this tip will help youunderstand why that is happening.Here is a tip that will help you... ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

The "Normal" button light keeps flashing. The door had come open during a wash cycle and there is still water in the bottom of the dishwasher. I've shut off the power, but the light still blinks. Model is KUDSO1FLSS6


The washer had been interrupted during the program cycle and so the main micro controller has hung up. You can remove off plug for few hours or iover night to reset the processor.\015\012Now make sure that the door latch is clicking and contact ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishwasher is reading "overfilling", but no water is in unit. Door can open, noise of motor or pump continues and will not shut off even with the Power switch. Only way to stop noise is to turn off the circuit breaker at the electrical panel. What does this sound like to you?


HI- The flood switch has been tripped. It is located under the unit and is not really accessible except by a Tech. The most likely cause it poor draining; if there is a little water left over from each part of the cycle then eventually the water ... Asko 24 in. D3530FI Built-in Dishwasher

I have a Bosch dishwasher, model #SHE4M06UC/50, and it shut off in the middle of a "quick wash" cycle with water still in the bottom. I checked the outlet and it still has power. The dishwasher will not turn on.


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0952 seconds