Having problems with your Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher ?

Haier dishwasher wont run and shows a code OP

\015 Dishwasher Haier model ESD401\015\012\015\012Haier dishwasher wont run and shows a code OP\015

Answers :

The code "OP" means the door is open. I would suspect you have a faulty latch. The dishwasher thinks the door is open and will not start the cycle.
Did you every get your this problem solved? I am having the exact same problem
Repair Help & Product Troubleshooting for Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Haier dishwasher wont run and shows a code OP


The code "OP" means the door is open. I would suspect you have a faulty latch. The dishwasher thinks the door is open and will not start the cycle. ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

Frigidaire dishwasher shows an error code of ER uo after only a small bit of water runs into the dishwasher shortly after the hot water starts running into the dishwasher upon starting the dishwasher up.


... Frigidaire Dishwashers

Neff dishwasher not running, showing error code e25 and e17


... Neff Dishwashers

Euro dishwasher model ED12GWA run for 101 minutes then stops & shows error code E1


... Dishwashers

Er code flashing and dishwasher wont run - Frigidaire Dishwashers


... Frigidaire Dishwashers

Electrolux dishwasher shows code 10 not filling fault and code 20 not draining fault but when running you are able to hear it filling and draining. Whats the problem.?


I had the same issue (Electrolux ESF 6251). I had both error codes 10 and 30. I found that the short hose connecting the inlet valve (solenoid) to the tank was cracked. That explained error code 30, but even after replacing the hose I still got error ... Electrolux Dishwashers

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Bosch SHI 6800 Dishwasher. Fills with water and heats but doesn't spray water around (ie run). Shows code "2H" on lighted display. How can I fix it?


... Bosch 24 in. SHI68 Built-in Dishwasher

Lower dishwasher won't run- shows a code of F2


... Fisher and Paykel DD24DCX6 Dishwasher

Hello, We have a Fisher & Paykel dishwasher m# dd602 znwn showing After we fixed a hole in the drain line an F1 code still appears and the pump keeps running. What should I do from here?


F1 means that your dishwashers have flooded. You can \015\012download the video in the link below to see how to get rid of the error \015\012and fix your dish drawer for n ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Error "HO" Dishwasher shows error code "HO" and is very loud with what sounds like a small lawn mower motor running while the message flashs.


If your hot water isn’t hot enough it will display “HO” while heating the water to operating temperature.Thank You HuumPlease remember to leave a solved rating before you sign off! ... Dishwashers

Dishwasher will not run and its showing a code of tE. Any idea what the problem might be ?


The thermistor is located between the terminals of the heater and comes as part of the heater assembly. You will need to pull out the entire dishwasher to replace it. The heater assy is stuck into the side of the sump,you can access it fr ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a Kenmore dishwasher 665.16022402 that is locked out at the board.( the clean light flashes continually & wont allow it to run) I don't have the manual to find the reset code and troubleshoot. There didn't seem to be any proublems till now.??????? any help?


... Kenmore 24 in. 16032 Built-in Dishwasher

I have a Bosch SHU5316UC dishwasher. The last two times it ran, my wife says the display said "CL" (for clean) after running through the cycle, but she heard a "motor running" until she opened the dishwasher. Attempting to run the dishwasher tonight, it won't start - it displays a "P" (error code?) when you attempt to start it. Can you tell me what the error code P is? Thanks, Dave


P stands for program in computer algorthms. The device displays program whenver chages were made to the default settings. A powered on devices least has malfunction only requires reseting to attaon default features. Depending on the type of device, r ... Bosch SHU5316UC Dishwasher

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers

Siemens dishwasher pump runs while door open wont turn on!


I have same problem no water in base float not activated and no blockage in pump ... Siemens 24 in. SL84A305UC Built-in Dishwasher

Thermador dishwasher DWU244, error code "F" does not run?


F code is a fill fault problem to much or to little water to determine the problem is to hit cancel drain buttons on the front of the machine and wait for cl on the display turn off machine and wait 30 seconds turn back on and the first thing you wil ... Thermador DWU244 Dishwasher

We had a problem with our garbage disposal and it resulted with water leaking from our dishwasher. The disposal is fixed, I removed the excess water from the dishwasher. I tried to run the dishwasher empty to clean it. It runs but then the E-2 alert shows on the control panel meaning high water level. I read in the book that I may have to have a service person do some sort of a reset. Is this correct?


Contacted the company and they e-mailed instructions to fix problem ... Asko 24 in. 1895 Built-in Dishwasher

I have a Bosch SHE56C05UC/40. The unit fills and drains ok but the circulation pump will not operate. I run the diagnosis according to another of you posts and came with an error code E1 which is a heating code. Why would this prevent the pump from running? Your diagram show a flow switch in the heating circuit which won't close unless the pump runs. A diagram of the pump circuit would helllllp.


Follow the instruction code in your ins.manual if you do not have go for free download : www. fitness.manualsonline.com or www.ret ... Bosch SHE56C02UC / SHE56C06UC Dishwasher

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

I have a Bosch SHU9955US/14 (Integra) dishwasher. There is currently a 0 with and asterisk showing on the display and the unit will not run.


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Thermal Fuse\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Bosch Dishwashers

My fisher and paykel dishwasher drawers is giving me an F1 error code, won't stop running and is acting like it's possessed.


... Fisher Dishwashers

My asko dishwasher ran great until recently. after finishing a load, the pump just continues to run (even when all water has been pumped from the unit and it's running dry) and the display isn't flashing anything (not codes, etc). Worried about destroying the pump, I shut off the washer at the breaker, and it's been a few months since we've had a dishwasher. Every once in a while I'll turn the power on and it just continues doing the same thing - it's stuck in this position/state, so I have to s


The IC that controls the pump seems to have gone kaput. Change the IC. ... Dishwashers

When exterior breaker panel was replaced, my Frigidaire dishwasher (model FDB989GFC2) was accidently wired to 2 breakers and briefly took a 200v load. It started, then immediately showed a Power Failure code and shut off. The wiring has since been corrected but the dishwasher now shows no signs of life. Is it terminal or can replcement parts solve the problem?


Hi\015\012\015\012\015\012Thanks for using FixYa. You’ll need to check the following things--\015\012\015\0121. Fuse (blown or tripped).\015\0122. Check the wire fasteners at dishwasher junction box. ... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1842 seconds