Having problems with your Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher ?

Settings buttons partially work and will not start

\015 All buttons on left light except Crystal/china and none of the buttons on right light including the start button. have had about 1 year with no problems except lower right gasket isn't real secure. otherwise problem free\015

Answers :

Basically, the Haier is a piece of ****. Parts are not available and the phone-in service (if you can call it that) will keep you on hold endlessly. Do yourself a favor and get a better machine.
Repair Help & Product Troubleshooting for Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Settings buttons partially work and will not start


Basically, the Haier is a piece of ****. Parts are not available and the phone-in service (if you can call it that) will keep you on hold endlessly. Do yourself a favor and get a better machine. ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

Pushing settings and start button but will not start. The green light comes on for the setting and the Heat Dry but once start is pressed it will not start and after 30 seconds the lights go off. Also, Smart Wash button no longer works


... Kenmore 13743 Staimless Steel Built-in Dishwasher

I have a Maytag quiet series 200, it been working fine since I purchased it last year, as of today I pressed start and it won't start and yet when I press the delay buttons of 2, 4, 6 it lights up and so do the other functions but to change my settings that doesn't work neither as well as my start button. Whats wrong with it? Any ideas? My model # is NY2222514


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

GE Potscrubber 1200h tempertature sensor The push buttons will not set (work) except for the Reset button...it goes in a cycle in about 30 seconds. Normal wash, etc will not set. They go a little over half way in but do not connect. When it first started we had to reset the GFI breaker.


Hi\015\012\015\012The issue seems to be with the control not working fine, it\015\012can also be due a bad control board. You can take it apart and check the\015\012control board, blow air with hair dryer on the control if bad replace it. ... Dishwashers

Kenmore dishwasher When I push start on my dishwasher it does nothing. The lights work on the wash settings and the dry settings but when I push the start button, nothing.


Thermador Fully Integrated Dishwasher (DWHD64CP) i just installed this unit myself i wired it up ran supply line it lights up i select a cycle i hear it humming but it will not start the cycle or if it is starting it is not getting water in the unit. ... Dishwashers

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

ADP6000WH/ADP6000IX Whirlpool Dishwasher. The controls are not working correctly. When I select the top two (Strong and Normal) settings I hit the start button the dishwasher will not run. When I select the other four (Economy, Rinse, glass and soak) settings the machine works fine. Thanks MB


... Whirlpool Dishwashers

I purchased a second hand Electrolux Dishlex DX403 with a kitchen. The dishwasher turns on when I turn the powerpoint on and makes a noise as if it is about to start. I attempt to press the buttons to set a mode and start it and it wont work, the buttons dont do anything. How can I fix this?


... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

I did the setting of my Frigidaire Gallery Dishwasher as every morning: set "both rack/ Hi temp wash/ Sanitize / Power dry off, and the related lights are all on, then I pressed the "Start" button, but nothing happened. The machine didn't start working. Model: PLDB998AC0


... Frigidaire 24 in. PLDB999S Stainless Steel Built-in Dishwasher

We have a Beko DWD5410W dishwasher that has worked fine...until today - the 'wash' light is on but it is not wasing. I have pressed in the 'start' button and held for 5 seconds to reset and it then springs to life draining out or whatever that noise is, and then if I turn the dial to a setting (even the cold prewash) and press 'start' again it starts whirring away, then after about 10 seconds just stops, with the 'wash' light staying on. Not blocked, I have checked - this likely to be a frozen p


... Dishwashers

The faceplate sometimes does not respond when I touch it, or if it does It may not let me cahgne the settings... Plus when the lights do come on the dishwasher won't start when I press the start button. When it does come on it works fine and has not had any other previous or current issues. Please HELP before I start whacking a hammer on this faceplate...


I also own a ADB1500AWB. The switch membrane failed within 30 days of purchase. It was replaced under warranty. The technician said this part fails very often. I bought an extended warranty. It failed again on 9/3. As of 10/13, the part is ... Amana 24 in. ADB1500AW Built-in Dishwasher

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Before I start a load, I can set the cycle I desire but the start button does not work or light up. Is there a fuse I can replace?


Hi,There is no reset switch but it sounds like you either have a bad \015\012control board or the unit isn't getting power for one reason or another.\015\012 Remove the kick panel below the door and look for the 3" x 3" sheet \015\012met ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

I have a whirlpool du1055xtsq3 dishwasher that is partially working. Cycle buttons light up but start button does not. I've tried resetting by pushing sani-rinse and heated dry alternately. Control panel lit up and heard motor running but no water. Your help is appreciated. Unit only 2yrs old. Thanks!


... Whirlpool Dishwashers

Our De Dietrich Microwave oven is not working for the past 1 week. Power supply is good, All timer control and other controls and working. When I adjust the settings and press the "start" button nothing happens. It is too costly to get it repaired. Please suggest a solution to solve this problem.


... De Dietrich 24 in. DVF120J Built-in Dishwasher

Describe your whirlpool du948pwpq Problem: I have a whirlpool du948pwpq dishwasher in a tenant's unit. They said the delay start button is no longer working. Also, they cannot "de-select" the heated dry option. It seems to be an issue with the electronics of the control panel. I've already tried to "unlock" the buttons - no change. I also powered off the unit in hopes of re-setting - no change. Does anyone have any other suggestions? I am hesitant to call a service person (it's out of warrant


... Whirlpool 24 in. DU948PWPQ Built-in Dishwasher

Mytg Dishwasher MDB9 does not start. The only button working on the touchpad is Insta wash, but that setting does not start the dishwasher.


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Whirlpool "Quietflight II" - Will not start. The button for "Delay" works, and the button for "Cancel/Drain" works. Pressing this button will drain the unit. No other buttons will work, however, and the unit will not start. Ideas? I've taken the control panel off and looked at it's guts, as far as I can tell everything looked ok (not burnt and no loose wires), although I am no electrician....


Have you tried testing the control panel with an VOM meter? You can press a button and test the wiring that would go to that particular circuit. See if you get a reading on the specific wire when that particular wire is pushed. Does sound like a cont ... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Mdb7749awb2 Will not start. Cycle and setting (heated dry, etc) work, but the Start/Resume button will not light. Any ideas?


... Maytag Dishwashers

Maytag dishwasher mdc4650 dim panel lights will not start and control panel buttons don't work to change any settings


... Maytag MDC4650AWB 24 in Builtin Dishwasher

The start/cancel button is not working. All other cycles light up and will set, but can not get dishwasher to start


... Jenn-Air 24 in. JDB1250 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0898 seconds