Having problems with your Haier HDP18PA Stainless Steel Free-Standing Dishwasher ?

Haier Dishwasher hdp18pa - Power reset

\015 I have a Haier portable dishwasher that keeps blowing the outlet fuse. I have tried plugging it in multiple locations. It blows the fuse when i press the power button.\015

Answers :

Are you blowing a fuse or throwing a breaker? Either way there is a chance that no outlet you have chosen to test with yet is on a circuit with sufficient amperage-I had this with a microwave I recently had installed. If you have the manual, check for requirements regarding amperage. You then need to be sure you are using an outlet with amperage comparable to the requirements-this is on your fuse or breaker. If your requirement is, say, 20 amps, a 15-amp or less breaker or fuse is going to fail. I had to go to a 'clean' circuit from my garage with nothing on it to find out I did not have enough amps in my circuit. My solution was a dedicated breaker. Another option is to use my second option (which I did not need), to plug it into a gas generator with sufficient wattage/amperage. This ensures nothing else is on the circuit.
\015\012
\015\012Failing all that, it could be the power supply for the washer, a circuit board issue, etc. Don't mess around if you don't understand electricity, though-it's not worth frying yourself.
\015\012
\015\012Finally, if it worked ok before and this has just begun to happen, I'd tend to think it's an issue with the washer itself. Hope this helps.
Repair Help & Product Troubleshooting for Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Haier Dishwasher hdp18pa - Power reset


Are you blowing a fuse or throwing a breaker? Either way there is a chance that no outlet you have chosen to test with yet is on a circuit with sufficient amperage-I had this with a microwave I recently had installed. If you have the manual, check ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

The dishwasher did not finish last rinse cycle. I have no power, no lights light up. I reset the breaker. Is their another reset button on the Dishwasher itself. I have a Quiet3 Power GE Dishwahser.


Hi,I am sorry to hear regarding the trouble.The best way to reset - Disconnect the power supply for few minutes, say 15 minutes and then turn it on.If the problem persists, this would confirm an internal failure.As ... GE Dishwashers

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

No power. Dishwasher will not come on. I checked power to power switch. It has power to switch. Is there a fuse in dishwasher, or a reset anywhere. It is a Whilrpool model.


Yeah, there is a fuse just enderneith the panel on the control board itself. It's white in color, and snaps on and off of the board. Very easy to replace. I bet that's your problem. Good luck :) ... Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Maytag Dishwasher. I believe the model no. is MDBH968AWQ3. We have had it installed for about a year and have had problems with it. We have had to have a latch replaced. Now the power went off the other night and it just flashes start/resume. We can't get it to reset. We have turned the power (breaker) off to it, thinking that it would reset, but it has not. Can you help?


... Maytag Dishwashers

Kenmore dishwasher My dishwasher stopped in the rinse cycle and no longer appears to be getting power, although the breaker works and the plug it is connected to is still receiving power. Is there a reset button for the motor, or some other idea to try and fix this? Thank you for your assistance. Mark


Mark, you probabley blew the thermal fuse located on the main board. Easy fix. Part number 8269213. You can ohm it out to be sure. You have to remove the inner panel to get at the control board. The fuse sits on the top side and clips on. Two wires ... Kenmore 24 in. 16293 Built-in Dishwasher

Need a reset code for Haier 4035 dishwasher - Haier DW12PFE2U Dishwasher


... Haier DW12PFE2U Dishwasher

The dishwasher quit during a cycle. I can't get it to start. I have power to all portions of the dishwasher. Do you think the motor stopped due to overload? Is there a way I can reset the motor? If so where is the reset button?


If the Dishwasher cycle does not complete \015\012\015\012Test the ... GE Nautilus 24" Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

ASKO 1555 dishwasher won't run. The anti flood device motor won't stop running but we've removed all the water. All the lights on the front panel blink in unison and when we hold down the start/cancel button on the front, nothing resets. We can't run our dishwasher. We've tried disconnecting power and resetting the circuit breaker but the churning motor won't stop.


Hello,Welcome to FixYa.Based on your description " The anti flood device motor won\\'t stop running but we\\'ve removed all the water " It is likely nothing very serious. ... Asko 24 in. 1805 Built-in Dishwasher

Looks like program in electronic dishwasher has locked into a cycle. the machine will not drain even after resetting it. Also it will not restart any program or cycle after resetting and recycling power. The machine is a classic electronic bosch dishwasher It has worked perfectly for three months


Im a old bosch tech . the problem is the module or the drain pump is stuck. if this helps please give me a 4 thumbs up post thanks. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Haus dishwasher need to reset it...no power apart from power light on water at the bottom of dishwasher


... Dishwashers

Hi, Had a power cut at my home and my Caple Di455DL Dishwasher was mid cycle on a glasswash program at the time, since power has been regained it will not restart or reset itself, it just lets a pulse of four beeps go once the door is shut and makes a sounds like its trying to pump out water? tried turning off at mains etc but cant get it to reset!


... Dishwashers

No Power My Whirlpool Dishwasher DU900PWKQO was working yesterday and now does not have power to it. Is there a reset button to press or can a dishwasher just stop working?


You probably have a bad door switch assm, there is no reset on this unit, if you have a bad door switch the unit thinks the door is open so it won't start. ... Whirlpool 24 in. DU900PCD Built-in Dishwasher

Where is the reset button on a ge dishwasher ? GE dishwasher won't start up no power is getting to the machine..checked breaker and plug in all ok is there a reset button located anywhere ?


... GE 24 in. GSD2000Z Built-in Dishwasher

Whirlpool dishwasher This dishwasher quit in the middle of a wash cycle,we had to empty it and wash by hand. I thought that maybe the breaker to the dishwasher popped but when checked it had not .I then noticed that there are no lights on the electronic key board .Even when not in use there should be one red LED that is lit. It almost seems as if there is no power to the dishwasher. Is there some type of backup safety switch or breaker on the dishwasher itself that I could reset?


Fuse on control board. ... Dishwashers

No power My dishwasher Model DMR77 quit working yesterday during a wash cycle. No power ie, no display light or tones. I am getting power to the unit, checked with a volt meter. I am thinking Power supply, or is there a reset on the unit.


Hi,\015\012 The main PSU is part of the control board. You may be lucky to find an aged fuse to replace, but it's more likely a power transistor that's fried.\015\012\015\012Unplug and remove the control board to see which bit's toa ... Samsung DMR77LHS Tall Tub Dishwasher

Portable Dishwasher Hello, We just got a used Haier portable dishwasher, model HDP18PA and while the hose connnects fine to the sink, the water isn't going into the dishwasher and is coming out of the connection. Does that make sense? It looks like, if it operates properly, the water should be sucked into the dishwasher but the connector isn't pulling the water in. Help! Thank you! Tara


You have to have a good seal. Get a hose washer from your local hardware store and replace both of them on the hose if they are like a garden hose. If you still don't get any water to the unit, post again and I'll step you through it. ... Dishwashers

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers

HDP18PA Stainless Steel Free-Standing Dishwasher: I have a Haier Dishwash HDW300SS, and it beeps 10 ...


... Haier HDP18PA Stainless Steel Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1967 seconds