Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

LX30H Hobart torsion bar adjustment

\015 I have a hobart LX30H when you open the door if you dont hang on it just slams right down. Is there a way to adjust the torsion bar on this machine, I called Hobart and was told no that i needed to buy a torsion bar ,torsion bar assymbly,and 2 o ring any help would be nice thanks\015

Answers :

Im a service tech for hobart,there are no adjustments,the torsion bar is broken.the parts arent expensive but installing them are tricky.
Bubbaloo
Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

LX30H Hobart torsion bar adjustment


Im a service tech for hobart,there are no adjustments,the torsion bar is broken.the parts arent expensive but installing them are tricky. ... Hobart 24 in. LXIH-3 Built-in Dishwasher

How do you reset the torsion bar on a Hobart LX30 comm. dishwasher? I have a new torsion bar but not the torsion bar assy.


... Hobart Dishwashers

Hobart lxi r/r torsion bar tube for door - Dishwashers


... Dishwashers

I have a Hobart Welder with a Kohler Engine CH20. It's 4 years old. It idles very radically and sometime dies at idle. At run speed it's normal and it starts right up. I have tried to adjust the idle speed with the solenoid adjustment and low idle speed adjustment screw but it will not idle smoothly and it continuously changes speed and sometimes dies.


Hello. your carbeurator is gummed up. go to any auto parts store and get two bottles of a product called seafoam. you will add this to the gas at the rate of one ounce per gallon. It will clean up your carb. and your kohler engine will work bette ... Karcher 2500 PSI Pressure Washer

Hobart LXI you seem to know a lot about the hobart, maybe you can help me. My hobart Lxi high temp is just now out of warranty, i am mechanically inclined, and need to adjust my detergent and rinse aid pumps. How difficult is this and how can i go about doing so. Both the pumps are running too much product.


Question--As of today if you look at the display does it read add detergent or add rinse aid?Im asking you this because theres a chemical pump circuit board that senses the chemicals on this d/w.And if the d/w displays those the d/w will keep dumping ... Dishwashers

I have a McCULLOCH 1500 psi pressure washer and it seems like I need the top part of therod where the waer comes out it no longer adjusts the water stream seems like a little plastic defkector that you adjust your stream with, snapped and broke looks like I HAVE TO REPLACE THE ENTIRE TOP PART OF THE 2 PIECE ROD on the bar it says the following max130barmax60C PA66-GF30 Where could I purchase this piece Andy Nowostawsky my adress is 15447-rue d'esterel Pierrefonds,Quebec H9H 1Y9


... McCulloch Pressure Washers

Hobart am14 How to adjust wash time cycle - Hobart AM14-253 Free-standing Dishwasher


... Hobart AM14-253 Free-standing Dishwasher

How do I adjust pressure? when i push idle bar, pressure increases but idle wont stay adjusted


... Karcher G3025OH Pressure Washer

Hobart lxi sanitizer adjustment - Hobart 24 in. LXIC-5 Built-in Dishwasher


... Hobart 24 in. LXIC-5 Built-in Dishwasher

Hobart low rinse pressure - Hobart Lx30h Commercial Dishwasher


... Hobart Lx30h Commercial Dishwasher

Adjusting soap intake on hobart sr24 - Hobart Dishwashers


... Hobart Dishwashers

Hobart line comercial diswasher - Hobart Lx30h Commercial Dishwasher


... Hobart Lx30h Commercial Dishwasher

Service manual for lx30h hobart - Hobart Dishwashers


... Hobart Dishwashers

Hobart LX30H Door does'nt close properly


... Hobart 24 in. LXIC-5 Built-in Dishwasher

Hobart dishwasher model LX30H displays -5 on


By the way you're describing the problem, i would have to say there is something wrong with your control board. part#473173 can be bought @ any hobart office in your area. dont forget to vote ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Running a Hobart LX30h as a low temp sanitizer


I can not verify this so DO NOT do this until you find out for yourself!\015\012 I am told that you can actually change the settings on the control panel to the LX40 mode by jumpering J1 and J2 then and then use the up down arrows until you see ... Hobart Dishwashers

Hobart LX30H leaking at door. Power drain works.


Leaking at the bottom edge of the door can be caused by the lower spray arm having a split or crack which allows water to spray directly at the lower door instead of up. A close inspection of the lower arm or watch it work with the door open. You'll ... Hobart Dishwashers

Hobart lx30h rinse additive is running all the


The main cause is the "anti flood" device at the bottom of the washer that detects a water leak "hose leak" etc. This device made up of a polystireen float and micro switch is a safety device and when activated puts the washer in pump out mode only. ... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Hobart 1712 slicer thickness adjustment moves. It


... Hobart Dishwashers

Hobart dishwasher model LX30H; displays wrench and E4.


Water is not to top sensor in alotted time.\015\012 Top sensor is in right rear corner, and is the upper of the two. Check the connector to the probe on the outside at the back. (sometimes gets wet fro vacuum breaker leaking when dirty or low f ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hobart dishwasher Am14, rinse cycle is too short. Can it be adjusted?


No rinse time can't be adjust on the am-14 modelit is built in main board non variable ... Hobart SR24C-4 Dishwasher

Tank temp Our School Dist. has a Hobart dishwasher Model AM 15 T. After filling the unit it reaches a tank temp. of approx. 160 F, but when it is run through a couple cycles the temp. falls below 140 F, the min. wash temp is 150 F. The supply from the hot water tank is approx. 140 F. The rinse cycle reaches well above the 180 F min. Is there anyway to adjust the tank temp. on this model or could you suggest a solution to the problem. Thank-you John Fry


Check to see if your element is scaled up or your element may be damaged ... Hobart AM15T Dishwasher

Hobart lx30H Fuse f1 3.2amp 250vac blown, f1 feeds relay board. No booster temp, pump and sump heater active (OK). Can problem be from other devices that are driven from the low power relays on this board or are we looking at a board failure as the only answer. No skinny on door panel, Can't get access to OEM repair manuals anywhere on line Thanks


Possible bad relay coil ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

Door latch does not fuly latch.can the latch u bar be adjusted to engage the switches soonr on closing ?


An adjustment to door catch won't be realiable or safe, ensure that the catch is not moved because of a losen screw.If that is not the problem, then the door lock assembly must be replaced. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0188 seconds