Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

Not able to enter program mode

\015 I have the manual that tells me to push the ON then push the OFF button and hold it to enter the progam mode after it reaches 99, but it will only goto 88 then all it does is just recycles 11,22,33, etc. to 88. I need to turn on the Rinse and Wash soap pumps they were turned off at some point. The machine is a LXIH 1300017. I am very capable of fixing any thing with the machine but this is driving me nuts.\015

Answers :

You need to remove the conrol drawer.Open the door,look at the top and there will be 2 screws,remove the screws then slide the control box toward you.You will see 2 circuit boards,the one to the right is the control board.You will see 2 white buttons marked prog and select.Hold the prog button in and the on button.You should now be in the program mode.
Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Not able to enter program mode


You need to remove the conrol drawer.Open the door,look at the top and there will be 2 screws,remove the screws then slide the control box toward you.You will see 2 circuit boards,the one to the right is the control board.You will see 2 white buttons ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a Baumatic BDW 45.1 slimline dishwasher, the unit will power on but I cannot select a program. I was able to place the unit in to reset mode once by holding down 'P' and power cycling the unit. This then allowed me to choose a program and complete a full wash cycle. Now I cannot repeat this steps and the unit remains with just power light on. There are no Error codes displayed at all. Could this be a problem with the front panel?


... Baumatic 18 in. BDW45.1 Built-in Dishwasher

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a FP DD602. Top drawer will not start. Can select different programs but sfter pressing Start , it just beeps and then nothing happens. Also cannot enter Diagnostics mode. Bottom drawer seems to be OK.


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Any of the programs start ok (water enters etc..) but the program does not move on, will stay at the same place early in the program cycle for hours. You can move the program on manually and the water ext will exit but the dishes are not properly washed. Changed program timer switch but still same - zdi6041x dishwasher - any idea why ?


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Zanussi 23 in. ZDI6041 Built-in Dishwasher

Bosch Exxcel Auto Option, 2004. SGS56E02 GB/47 Stopped mid program all program lights flashing, on re-set several program lights illuminated, able to select rinse program but several lights illuminated and fails to pump out at end of rinse. What has gone wrong?


... Bosch 24 in. SGS57E02 / SGS57E08 Exxcel Free-standing Dishwasher

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program faked to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg STX2 Dishwashers

Ge pdw9880 dishwasher keypad issues - only one mode worksrncant change modes - cant enter factory test mode is it the module?


Yes, it needs replacement. The micom(program) is corrupt. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program failed to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg 18 in. STX45-1 Stainless Steel Built-in Dishwasher

I have a de dietrich built in dishwasher model DVH610JU1. The program appears to start but no water enters the machine and when I open it the lights flash (program light and end program blue light)


... De Dietrich 23 in. DVI130 Built-in Dishwasher

I have a Blanco BIDW605 dishwasher, which when program selected and door is closed will not run as usual. Scavenge pump activates & water can be heard entering the system however the main pump does not seem to activate. Have tried all the other programs with same result. Checked water input filter & is ok.


... Dishwashers

The motor continues to run with the diswasher powered off. In addition it will no longer enter wash mode. It can be powered on and wash mode can be selected, but nothing happens except the motor continues to run. Cycling the power feed off and back on does not solve the problem.


Hello John,\015\012\015\012The simple answer (without looking at the wiring diagram) is the float switch. The simple answer (after looking at the wiring diagram) is the float switch. I've posted the wiring diagram for this washer to Flick ... LG 24 in. LDS 5811 Built-in Dishwasher

ELS63010/S-No 91210714 Electrolux Dishwasher On Controls Top Red Light is flashing.I am unable to get back into normal program mode,and i am not certain if machine is filling. How do i get into setting mode


... Electrolux 23 in. ESL624 Built-in Dishwasher

Dishwasher ARISTON LI625. My program light do not turn on, so i am not able to see whe selecting the program. What do I have to do?


... Dishwashers

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

Hello, My Ariston LSI 68 A dishwater have a problem: During the washing in reduct mode,(the 3rd program from left) after about 1 hr , he does'n end the washing and blinking the second light from left. (the normal washing program). In the dishwater still remain about 1 inch of hot water, the drying never start. If you can send me the blinks codes of my dishwater i appreciate very much. Thanks Leonardo Italy


The Ariston dishwasher alarms should be in the user manual. However, I cannot find the manual for your model. \015\012\015\012But I have found ... Dishwashers

Thanks so far! However, with the bottom drawer out and the top drawer open...I enter the diagnostic mode. I can scroll through the hardware output test mode. All the led codes appear correctly. However, none of the actual hardware responses occur....the water does not fill, lid does not move.....etc. What am I doing wrong??


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool dishwasher model GU1500XTLSO Control panel is mostly not responsive. Can enter "control lock" mode by pressing and holding "air dry". If I press air dry again in this mode, the green button flashes three times. Does this mean anything? I would really appreciate some help.


... Whirlpool Dishwashers

I am looking for an F&P DD60DCX6 service manual which covers the service codes in diagnostic mode, to enable ON/OFF switching of individual components. I already know how to safely enter diagnostic mode


Here the service manual. ... Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

How to enter service mode "service mode"


... Dishwashers

F&P Dishwasher DW60CSW. All program modes working but does not


... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Unit will not run. cannot enter diagnostic mode.


I would say that you have a bad touch panel..99 percent positive ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0281 seconds