Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

Hobart LX15H indicates E4 and will not fill.

\015 Have cycled power, cleaned sensors, still will not fill. Any ideas?\015

Answers :

Also looking for help troubleshooting our Hobart X18 dishwasher.
This is what I found in the manual...and on a couple of other sites....

Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")
\015\012
1.Low water pressure — check for clogged hose strainer; check that site water pressure meets minimum flow pressures.
2.Make sure probes are clean.
3.No water pressure — main water supply valves may not be working.
4.Drain\015\012valve open - turn machine off to drain machine, then on. Repeat twice\015\012(this assists in clearing any drain valve obstructions). Wait for\015\012machine to reach READY mode and press WASH. Slowly open door several\015\012seconds later and note water level. Close door; 30 seconds later, open\015\012door slowly and check that water level is the same as it was. If not,\015\012repeat the
OFF-ON procedure.
5. Delime machine.\015\012\015\012

If this doesn't help let me know and I will get to the bottom of it....good luck and thanks for rating my effort...The Fang.
Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hobart LX15H indicates E4 and will not fill.


Also looking for help troubleshooting our Hobart X18 dishwasher. ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hobart LX15H Diswasher wont fill. Displays E4.


E4 error is for 1. Low water pressure - check for clogged hose strainer; check that site water pressure meets minimum flow pressures.2. Make sure probes are clean3. No water pressure - main wate ... Dishwashers

Hobart lx30h replaced all sensors and have no more error codes but the machine says fill but never fills and wont turn on wash cause it thinks its filling...any advice?


Are you sure that you have all the connections rights? Did you check the voltage at the water fill solenoid? ... Dishwashers

I have an H62 Hobart commercial dishwasher. I had it on fill to start it up. There was a loud pop while it was filling and now it has stopped. The power light is still on but the dishwasher will no longer fill. Where should I start looking for the problem. Would it be a fuse that popped?


... Dishwashers

Our church has a hobart LXIH 130017 and it stopped filling all the way. When turned on it will start filling and then stop and the fill light will flash. Any Help


... Dishwashers

Hobart lx-g HI there, I have a weird problem with my dishwasher... when I press the off buttom, instead of staying off... it restarts by itself. Also, when it starts filling up, water overflows from the machine ( when it filling up the temperature rises alot more then usual it reaches 190f) and then i turn off the machine to stop the flooding... can you help?


The problem with the machine restarting is with your keypad, the on button is stuck on and needs to be replaced or you can continue unplugging it. Your other problems are most likely caused by lime build up, is the inside of your machine white. I ... Hobart 24 in. LXIH-3 Built-in Dishwasher

My hobart lx 30 will not fill all the way. iv bin to hobarts online manual and iv got plenty of pressure..flashing wrench e-3 code etc...added 2gallons water but presumebly since it wasnt 150degree water that didnt help as all i was able to do was turn off and back on and watch the 3gallons expell


LOOK FOR WATER PRESSAURE SWITCH PROBLEM ... Dishwashers

I have Hobart dishwasher when I turn it on star to fill then nothing happen after that , it continue to say fill and no water going in the machine , and won't let me run a cycle plz let me what the problem


It is possible that themachine does not start off the cycle because there are errors or feedback fromthe inputs. For the program to start up the main program controller mustinitiate the INLET/PUMP MOTOR/DRAIN to workwhen it is commanded .If thi ... Hobart Dishwasher Accessories

I am on the ship, we purchased Hobart AM-15-5 door type dishwasher. Hobart did not provide the detergent dispenser (because they do not make them) and we do not need preloaded ones from Ecolab. Is there a manufacturer that makes only the dispensers that we can fill with our own detergent and that are compatible with AM-15-5? Where can we find it?


You have a few options for getting commercial grade detergent pumps which can be used with commercial dishwashers like Hobart.\015\012\015\012In case you do not have the manual for your dishwashwer you can get it ... Dishwashers

My mdb7100awq has stopped working. it does fill but they stops when the float assembley indicates either enough or to much water. Pressing the drain /off -the same as wash indicates lights and shows numbers andt there is some clicking but no washing.


... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Hobart lxi fill keeps flashing - Hobart 24 in. LXIH-3 Built-in Dishwasher


... Hobart 24 in. LXIH-3 Built-in Dishwasher

We have a Hobart lx18h dishwasher in our small restaurant. It suddenly displayed a P3 error code yesterday and would not fill with water. There is no one in our small town who wants to look at it and I'm afraid we can't pay hobarts rates. Any help will be appreciated. Thank you! [email protected]


Hello &\015\012Welcome to FixYa\015\012\015\012P3 error code\015\012means open or shorted booster thermistor and needs replacement. To replace this\015\012part# bottom panel comes apart with the unit unplugged and then ... Dishwashers

Hello I have a Maytag Quiet Series 300 dishwasher model #MDBH955AWW that is making a lot of noise. I saw an exchange on this site where the expert suggested filling the washer to just above the heating element, running it, and seeing if that solved the problem. I tried that and it solved the problem. I believe the expert said this indicates the fill valve needs to be replaced. Can you tell me which valve I need and advise me on how to change the valve? The manuals I have (Use & Care Guide and In


Http://sites.google.com/site/cwyffimsbffoe/maytag-dishwasher-parts-manual- ... Maytag Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Am14 will not stop filling on initial fill - Hobart AM14-253 Free-standing Dishwasher


Check the underneath the drain stem (lift up food catching screens inside the machine - drain stem will look like a long hard plastic tube) you may nee a flashligh when you tak out the tube to see the actual drain hole/ swirl your finger around the h ... Hobart AM14-253 Free-standing Dishwasher

Does anyone know how to change a hobart lx 18c from fill and dump to modified fill and dump?


Cant be done sorry ... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Hobart lx30h built in dishwasher when you turn it on to wash it shows p2 then it says fill but it want fill up with water also do you run cold water line to washer or hot water


The supply to the d/w should be at least 120degrees.the p2 error is a bad booster probe. always use hot water feed ... Dishwashers

Dishlex Global 300 Fills and then stops. faint electrical smell after a while . Checked heating element that I replaced 8 months ago, seems OK. It has 29X? ohms resistance and looks OK. (I am not sure of the reading on my meter but the element is not fused.) Pumps water in and out OK No blockage in pump or filters Water level looks to be low on filling, only part covers the heating element. I tried instruction book on changing water level using the "Eco" button no response as indicated in


You need to open the front cover and check the wiring for any burnt wire,this happen sometimes,if that does not solve then it't either pcb or electric motor causing this smell.You would be better off with a new one then. ... Dishwashers

Have Hobart CL-44E dishwasher that won't stop the 'fill' cycle. Both upper and lower float/probe sensors test as operating, Solonoid valves both functional; Display reads 'tank filling', and will not go into 'wash' cycle...what to do??


... Hobart Dishwashers

My cda CW195/1 dishwasher keeps running for 5 mins then beeping, salt indicator was flashing but have now filled up and the indicator has gone off, i have cleaned the filter, turned off and on and tried on a high setting but it still it beeping like there is a problem!


I am having the same problem. It's a piece of rubbish. ... Dishwashers

Maytag MDBTT79AWW dishwasher fills and nothing else. Once filled you hear a click, followed by a humming sound for 3-5 seconds, then silence. This will happen two or three more times, and then unit will shut off. Motor doesn't start. Repairman says he thinks control board is bad, but he sounds like he is guessing. I performed a field service test , which indicated a fault in the high current motor circuit. Unit is seven years old. Don't know whether to attempt repair, or replace.


That sounds like the motor trying to start but being jammed it is shutting off via an internal breaker. Check for something in the bootom of dishwasher that might have gotten down there that could do this. You might have to take the sprayer off and s ... Dishwashers

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

My cda cw195/1 dishwasher start button is flashing 7 times what fault is this indicating. Also prior to this the machine fills then stops drains then bleeps 3 times to indicate program has ended


... Dishwashers

Hobart fx-70 filling problem - Hobart 24 in. LXIC-5 Built-in Dishwasher


... Hobart 24 in. LXIC-5 Built-in Dishwasher

Hobart LX30 not filling up to capacity and displaying E3 code with wrench.Water valve is good. solenoid is good. no restrictions and water probe works. what could be the problem . I am very fustrated


... Hobart Lx30h Commercial Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0702 seconds