Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

E4 error after attempting to fill and get to temp

\015 Hobart LX18H Dishwasher attempts to run normally and goes thru fill steps and then displays an E4 error\015

Answers :

This is what I found for the E4 code...hope this helps...and thanks for rating my effort...The Fang.


Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")
\015\012
1.Low water pressure — check for clogged hose strainer; check that site water pressure meets minimum flow pressures.
2.Make sure probes are clean.
3.No water pressure — main water supply valves may not be working.
4.Drain valve open - turn machine off to drain machine, then on. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the
OFF-ON procedure.
5. Delime machine.
Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

E4 error after attempting to fill and get to temp


This is what I found for the E4 code...hope this helps...and thanks for rating my effort...The Fang.Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")\015\0121.Low water pres ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

We have a Kenwood KDW8ST2A dishwasher. We used to get the error code E3 (when still under warranty) and were told not to use dishwasher tablets as it generated too much foam. The problem has been intermittent but now we get the E3 error every time, no matter what program we run, or how little detergent we put in. I've a feeling its not heating up properly, is there any way to check the heating element? Is it worth attempting a repair?


... Kenwood KDW243A Builtin Dishwasher

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

Dishwaher -Maytag MDB4100 - is making a terrible noise as it is attempting to fill and It does not fill with water. Could the fill valve be the problem? If so, where it located and how do I get there?


It should be under the front side. i would definitely replace it. Turn off water first. ... Maytag Dishwashers

E1 error LG Dishwasher wqill not fill and get E1 error after about 5 minutes. Any suggestions.


Called a repair man and 400.00 all fixed ... Dishwashers

I am getting an IE error on my control panel. It seems to start ok but once it starts to fill with water the IE error comes up and the machine shuts off. How can I fix this?


You do not list the manufacturer and model number, but it sounds like you own an LG dishwasher.The IE error indicates that the water is not entering the dishwasher or it is entering too slowly / with little pressure. It is important to c ... LG Dishwashers

Bosch logixx dishwasher sounds like its running continuously & will go through entire program but does not fill or wash. Filled it with hot water manually to try for air locks & it does drain out. Then continues to attempt to drain even while door is opened. My amateur guess is that its a float switch but can I get at it from the inside or from the back? If thats what it is. Hope you can help,thanks.John


... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

I have a Hobart LX18H that has a P2 error code, the temps are a little erratic and its having a hard time getting up to temp. any ideas on what I should be looking for?


... Hobart Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

Follow-up I've removed the lower arm, I'll spend some time and see whether I can get the pobem sorted out. My wife noticed the the detergent was smeared all over the door and repeated tries didn't get it out. Therefore, the water is not spraying. I can confirm the water is filling on the bottom and draining. The heater is working well. I am thinking there is no pressure to send the water through the tubing to the upper and lower arms. The motor is hot to touch (118 degrees with my temp probe). I


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

My Frigidere dishwasher 400 Series AquaSurge w/Speed Clean has an error light Er S It indicates low rinse aid but I have filled the dispenser..I can't get the start/cancel button to work or to mov


... Dishwashers

My dishwaser fill up then i get E1 error code to say it has a leak I have pulled the cover off and this is not the case.


If there is no leak possible problem is that the water entering the dishwasher is coming in to slow may be a blocked filter at the tap or dishwasher or you have a faulty water valve also check that you drain hose is not to low causing the water to se ... Dishwashers

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

New montpellier dishwasher connected up and not filling getting error code e1


... Dishwashers

I attempt to turn the dishwasher on, but it will not fill with water. Instead, all I get is a humming sound.


Hi,Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Trouble No Water entering Dis ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Hobart lx3 dish washer fills heats and then drrains when wash cycle starts also get error code EO


... Hobart 24 in. LXIH-3 Built-in Dishwasher

New World Integrated Dishwasher DW60 E4 flashing and beeping. Managed to get it going for a while with a d/w cleaner, it filled, water heated but then E4 error kept flashing and it stopped, had to scoop water out. Cannot find instruction booklet to check fault. Please advise. Many thanks.


... Dishwashers

Water fills the bottom but never advances to the next mode(wash. Is there a way to get an error code?


Hi,Remove the kick plate from the bottom and fell for water in the tub. If the unit over filled due to it not draining there will be water in the base pan. The water will trigger it to be in flood mode (constant drain) until the water is ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

Le error when water gets near the top of the fill area verified water hose ok and changed inlet solenoid valve


Hope this helps\012Display Condition LE = Motor ErrorPossible Cause For Error Occurrence:Wiring connection is OK?The Impeller of Washing Pump islocked.The rotor of Washing Motor islocked. ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Maytag Quiet Series 100 series: When wash cycle starts, water gets filled in, dishwasher attempts thrice to start but then it gives up and all lights turn off.


... Dishwashers

My Miele Dishwasher (Excella Series G 2630 SCi) fails to fill. I get the message "Water inlet - Open the stopcock". I checked the water inlet filter and looked for hose kinks to no avail. I even checked the non-return valve. When I start the dishwasher I can hear a low hum (Not the pump) for a few second before the error message displays.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

OE Error I'm getting an OE error which is a drainage trouble error. I checked the hose and the drain, and everything is clear. My diswhwasher runs 98% of its full cycle and usually with 2 minutes to go I get this error. I have 2 opinins as to why this is happeneing. 1. Maybe the clog is in my trash compactor, however that seems to be working fine and my sink is funning with no slow down. 2. My 2nd theory is I have to reset the progam within the dishwasher. Like how sometimes I


Had the same problem and had the pump replaced ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1136 seconds