Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

Hobart dishwasher sitting at hot temp (174), constant steaming from unit, bottom rinse wand spinning & humming non stop? We reset prior to problem because it was not rising to temp (sitting at 106-112)


Answers :

Bad thermostat or contactor
You are in luck, the LXI series are easy to troubleshoot. Be carefull of the high voltages present.
\015\012If you open the top drawer to expose the control and relay boards you can see the status of everything. You will need a small magnet placed in the drawer, on the door switch in the front right corner to make it think everything is closed. Make sure the door remains closed or you will get very wet.
\015\012If the bottom rinse arm is spinning non stop, it could be the water valve has not closed, or the boster is stuck in heat mode. There are LED's on both boards to show status. If the light is on, it is active.
\015\012 The LXi gives two temperature readouts, wash and rinse. If its constantly flowing water, the booster will never recover to the set point of 186. Fix the flow first and see if the temp poroblem goes away.
\015\012Golder rule of trouble shooting. If you have more than one fault, and you know how to fix one of them , do it first and then re test
Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hobart dishwasher sitting at hot temp (174), constant steaming from unit, bottom rinse wand spinning & humming non stop? We reset prior to problem because it was not rising to temp (sitting at 106-112)


Bad thermostat or contactor ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

After starting wash cycle the rotary dial advances to what appears to be the second phase and stops at about 1 oclock position. I replaced the timer/switch, same problem. Could I have a water temp sensing problem due to a poorly adhered sensor? I thought this may be the issue as the sensor at the water feed near the soap dispenser was loose on inspection. Model Bosch SHU4002UC/U06 Under counter Dishwasher


Check the thermostat sensor. If the sensor is faulty the amchine will not detect that the right temperature is reached and the cycle will not advance.The thermostat will read low ohms (about 1K) using a multimeter at Rx1 at ro ... Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

DISHWASHERHD98E I stopped my dishwasher a minute before the cycle had finished. Now when i try to start it up again the 1 minute number comes up but gets stuck on this so that the 1 minute does not end (fan can be heard working) and I am unable to reset the programme. What can i do to overcome the problem.


You have probably flooded the base of the machine and it now is in flood mode take side panel off and have a look and drain water away common fault ... Hoover 24 in. HD98E Built-in Dishwasher

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

My kenmore elite model # 253.4448370 keeps beeping and won't stop. We try to press reset button because high temp and power failure lights are flashing but when we press reset button it doesn't seem like the button works..it doesn't reset like it use to...does anyone know how to make this beeping stop? It appears that the temps are right for both frig and feezer but beeping won't stop...HELP!!


... Kenmore Dishwashers

Am15 dishwasher problem: The pad will only turn on and off. Can't get it to cycle. Was on cycle 4 needed cycle 1. Got it to cycle 1, but now on and cycle does not work and when I push the off button it reboots to on. I put new pad on thinking it was the pad but same problem. Question: Is there a way to reset the board? should I be looking some where else? I cut the power at the breaker box to see if that might reset with no luck.


... Hobart AM15-2 Dishwasher

I have a Kenmore ultra wash quiet guard 3 dishwasher with a Hi Temp Wash that won't stop flashing. I've tried shutting off the circuit breaker and every code button sequence I can find including pressing Hi temp wash, heated dry, hi temp wash, heated dry...but it won't stop blinking..always blinking...Anyone have any other suggestions to reset this?


... Kenmore 24 in. 17019 Built-in Dishwasher

Soap problems Not only won't the soap dissolve but there are granules on the inside of my glasses. The dishes are also not getting very clean. I have been using cascade 2 in 1 action packs for a few months now with no problem, they've been great. I ran a wash 2 days ago and when it was done, I opened it up and the dishes were still dirty and the action pack was just sitting there slightly open with detergent sitting on the bottom of the machine. I had done a wash 2 days before with no problem.


Either: 1. not enough water gets into the dishwasher. open the dishwasher 3-4 times during cycle, you should see some (quite some) water at least once, if not - check water valve, water level float and water pressure. 2. the pum ... Kenmore 24 in. 15689 Built-in Dishwasher

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

I have F&P DD603 with problem with bottom draw. Once a programme is selected and door is closed, the dishwasher beeps three times then tries to start itys cycle. It then starts but stops every 1-2 minutes (like pause botton has been pressed). If you press start again it starts for 1-2 mins then stops again. I have tried turning off the power and totally cleaned out the dishwasher but no change? Any suggestions?


Hi \015\012When you pull out the drawer, pay attention to the bottom near the bottom front panel, you will see a little tab. this tab is at both sides of the drawer, press these tabs in and pull the drawer fur ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My asko dishwasher(1504) keeps running sometimes, The time will run down to 1 min on the disply and stay there and run on and on until I turn it off. Prior to this another problem occured, when the washer does shut off on it's own, the display will read F1(Falt in the heater), I am wondering if one problem has to do with another. The heater problem I can deal with but not the continueous running.


F1 doesn't mean that it's always the heating element itself, often it \015\012can be the control board relay that has shorted and isn't sending power \015\012to the element. If the element is the faulty part, you'd be looking at \015\012about $250 f ... Dishwashers

My Bosch SHE45M built-in dishwasher is suddenly taking an extra-long time to go through its cycles. On Regular wash it will countdown from 117 minutes to 31 minutes. When it hits that time it resets to 87 minutes, then counts down to 1 minute and will not stop. I have to hit the cancel-reset buttons for it to drain. I have tried to do a hard reset by cutting the power at the breaker for 20 minutes or more. I'm interested in potential parts and a description of how to fit it! Thanks in advance.


... Bosch SHE45M06UC Built-in Dishwasher

Ge triton I got my GE triton about 2 years ago and it has worked fine since. For some reason, now, it won't stop running through the wash cycle. I can't get it to turn off. I push the reset button hoping it will stop and all it does is go to "sensing" then back to wash. I have to open it to get it to stop temporarily, but there is water sitting at the bottom of it. Any suggetions?


Turned the breaker off and then on again.....\015\012Works like a charm!!!\015\012Thanks ... GE 24 in. GSD6660GSS Built-in Dishwasher

XL30 Hi temp. Two problems: 1) Hi temp booster not working...worked on and off for awhile, now won't get up to 180. 2) Turned on today and water flooded out. Water overfilled machine, turned off and heard pump drain unit.


To attempt to solve the over filling, clean the probes in the back right corner. Use a green scrubby pad.\015\012\015\012There is also two probes under the front screen. Clean them too.\015\012\015\012As far as the booster not ... Dishwashers

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

Sensorlogic dishwaser 50879 the problem is that after just few minutes it stops and blinks e.g on 26min and I must push the button again and then it continues. It may also stop at other "minutes" during the programme. It seems as if the digital side of the washer needs to be "reset" in someway


... AEG 24 in. Favorit 40850 Free-standing Dishwasher

I have a Bosch SMU2046Uc/14 about 15 years old. Sometimes it works, sometimes not, for the last couple of months. Now it has stopped working completely as if no power. Checked the breaker. Another problem - one of our kids just today jammed the door lock on it and we cannot get the door to latch at all. Can you help with any one of these problems? How do you fix or reset the door latch??? What else can we check to troubleshoot the dishwasher? Thanks!


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Hello I have a Fisher & Paykel dishwasher, model DW681ES. The problem is that it stops in its cycle. The reset button keeps flashing. I open the door and there is water at the bottom. It will not drain away. Is there a way to reset the system? Is there something else I can do?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the cycle doesn't complete, then the first thing\015\012that should be checked is the Timer and then ... Dishwashers

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Stopped working no power light come on like it's dead.The power supply is fine to the plug and the fuse is ok it just stopped why? is there a reset button anywhere?what would cause this? no hint of a problem before


Check where the pig tail the plug going into the wall follow the plug wire to the connection at the dishwasher. You will need to remove the bottom panel of the dishwasher at the floor. This access panel allows you to see the underneath of the dishwas ... Dishwashers

Blanco BFDW6 dishwasher drains and sounds like it is going to start but stops after 2-3 seconds. Yesterday it was playing up and made a fairly small puddle on the floor. Electrics seem to have been a problem from early on as after a few months it would let me open it during the beginning of the cycle to add items without needing to restart program. I am not sure if problem is electric (may need a reset?) or due to anti-flood feature.


... Frigidaire 24 in. FDB126RB Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1430 seconds