Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

Door well not stay closed.our door hinges replaceable


Answers :

If your machine is a Hobart LX series, changing the hinges will probably not remedy your door closing issue.
\015\012
\015\012I'd start at the door magnet. It's located under the handle at the top RH side of the door. Verify that it is there. Next I'd check to see if the other magnet is in place at the top front RH side of the top interior 'ceiling'. It's held in place by a bracket that runs the entire width of the unit.
\015\012
\015\012When the door is closed, these two magnets attract to each other with a firm "snap" and that is what keeps the door closed.
\015\012
\015\012If your door wants to spring open slightly or lazily rest closed without the above mentioned "snap" then you'll need to visually inspect the bottom edge of the door for any cracks or deformation, particularly in the corners. This deformation will cause the bottom of the door to bind against the lower threshold of the machine and keep it from closing. You'll have to remove the door to properly inspect and reform it.
\015\012
\015\012Sadly, my money is on the door being deformed in some way. Hope this helps.
Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Door well not stay closed.our door hinges replaceable


If your machine is a Hobart LX series, changing the hinges will probably not remedy your door closing issue.\015\012\015\012I'd start at the door magnet. It's located under the handle at the top RH side of the door. Verify that it is ther ... Hobart 24 in. LXIH-3 Built-in Dishwasher

My KitchenAid dishwashers door will not stay shut. I have replaced both hinges, the plastic rollers for the tension lines that atached to the spring. Still no luck. Could it be that the locking (?) switch has worn out?


Sure thing. \015\012Our dishwasher is one that we put our own "Door on it" in our case, it matches the cabinet. It is designed for that. \015\012I went on-line and ordered the replacement parts. I can't recall the site but I will look thr ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Maytag DWU8250BAX and the thing leaks like crazy. I just replaced the door gasket, but that is not the problem. When I took a closer look at the door it seems as though the water is getting up and into the door through a space in the bottom of the door. It seems to me like there should be another door seal to fill a gap that sits between the door hinges. If anyone knows if there should be a seal here and then what the part number might be that would be great. Thanks!


There is an airgap under the door..it should spray up and run down the door not spray up under it..look for crack or hole in spray arm..if there is the wrong soap in it it will flood out with lots of bubbles..just have to flush it out. lastly, if you ... Dishwashers

I have a 13-year-old Maytag DWU9906BAE. It has worked well but the door now opens too far - about 20 degrees lower than horizontal. I've taken the door apart and the reason is that the upright part of the two L-shaped hinge plates no longer catch on the back of the door jamb; for some reason they are now angled too far out and miss the catch plate on the back of the jamb completely. I'm no expert but they don't look warped, nor does the frame that they attach to. They're made of stamped


... Maytag Dishwashers

Kenmore Tumble Action Washer, Model 417,44152400 LEAK! Leaky Door got progressively worse over a month. I replaced the boot and about 10 minutes into the first test wash there was a massive leak under the soap dispenser and down the hinge side of the door during a fill cycle that seemed to be going through the dispenser. This happened again during another fill through the dispenser. No leaks during subsequent fill through the boot hose, before the spin cycle and no leaks around the door


Any of those could be the problem. Theres no other way to diagnose and fix unless/until you open it back up. ... Dishwashers

How do I replace the spring in the soap door? Spring appears to be broken because it is sticking out from the door. Door will not stay shut.


It depends on the breakage. Contact service center and get the part replaced. ... Bosch 24 in. SHU43 Built-in Dishwasher

Have replaced the door latch on my ld 4120m but now the door will not stay closed


Check and see if the catch loop is not broken off. ... LG 24 in. LDS 5811 Built-in Dishwasher

Model kuds 02frb10 serial # fs4604161 at first use attempt after install door would not latch, unit is in st thomas usvi where there are no kitchaid authorized repair people; local repairman has replaced latch, gasket, and door hinges all to no avail; now he says not repairable and it is junk to throw away; help


Hi\015\012\015\012\015\012\015\012\015\012This is a common problem not only for your type of dishwasher but also with other models. You need to unscrew the screws on the inside of the door. After all the screws are taken out ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

I have a kitchenaid superba diswasher that one of the door hinges has either popped off or broken. I need instruction on how to get into the door to replace it. Model KUDS01FLSS2


After taking the bottom cover off, I noticed that it's the cheap string that's broken and not the spring. I'm assumming that's pretty easy to replace? I've ordered the parts and just waiting. Any tips on replacing it would be appreciated. ... KitchenAid Dishwashers

Problem with door hinge. Door locks but falls to fully open position when not locked rather than staying ajar 6 inches. Dishwasher circa 10 years old - " Orbital System"


Look for a broken spring at the hinges. May need to remove the inner door panel. ... Dishwashers

KITCHEN AID STAINLESS DISHWASHER MODEL #kuds02frssWe just replaced both springs in the door and the latch mechanism and the soap dispenser that still does not work. Our door will not stay shut. MY HUSBAND NEEDS HELP.. PLEASE HELP. HE IS VERY GOOD AT REPAIRS AND IS STUMPED!!


Hi.Your husband must check wiring harness from electronic control to door lock solenoid.The solenoid should also be tested reading Ohms with a multimeter.Here parts and diagrams: ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

I have a GE Triton XL that leaks from the left side of the door. I assume I need to replace a gasket, but can't find it. Do I need to take the door off it's hinges?


Couple Things... Is It Level Left To Right And Slightly Tilted Rearward\015\012From Level..... Next Remove Inner Door Panel And See Where Water Is\015\012Coming From Shld Be Stained And/or Wet\015\012\015\012\015\012\015\012make sure the diswas ... Dishwashers

How to replace hinge on danby stove - Danby 924416 - Dgr 20 O-Door Hinge Wh Spr


... Danby 924416 - Dgr 20 O-Door Hinge Wh Spr

SMEG STX 45- the programme transfer- on the top edge of the door -has washed off over time so it is now impossible to read. any ideas of what to do? maybe a replacement door? the machine is 10 years old but working well. thanks


... Dishwashers

My dishwasher has suddenly started leaking water all along the bottom of the front door (where the door hinges). Is there a gasket that I need to replace?


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

REPLACE GE OVEN DOOR HINGE REPLACEMENT JSP40 - GE Kenmore Whirlpool Stove Bake Element


... GE Kenmore Whirlpool Stove Bake Element

I have a GE dishwasher (purchased in1992) the door falls open I suspect a broken spring. I looked all over the door hinge and cannot locate a spring(s). Where are they located. Also because of the age would I be better off to just replace the washer?


... Maytag Dishwasher

Replace screws in door hinge of fisher and paykel elba dishwasher


... Dishwashers

The door will not stay closed. We can hold it closed. How do i replace the switch. Where can I order the right part.


Repairclinic.com ... Kenmore 24 in. 17032 Built-in Dishwasher

Door on dishwasher, model KUDSO1FKSS1, came crashing down. I removed the front under panel and discovered 2 nylon cables hanging down and 1 piece of broken plastic. Does anyone have a diagram of how these need to be installed? and, should springs be replaced at this time as well?


Hello, Welcome to FixYa.\015\012\015\012While I don`t have diagram or illustration I can give some insight because this is actually very common.\015\012\015\012It is a fairly minor procedure to replace it/them. Slide the entir ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

The door on our dishwasher no longer opens gradually, it slams to the ground. I think it is the hinge or spring mechanism but I don't know what I need to replace.


You need to open the washer and then remove the side pannels (sometimes you must first unscrew fro back and the front bottom of the washer). Some have sprinngs that just unhooked and some have springs and nylon rope etc attached to the door spring th ... Dishwashers

Broken door hinge - need a replacement dishwasher but this one is out of stock (bosch shv46c03uc) i need to find the bosch that will accept the same front panel as my old d/w


You can get the door here:http://www.repairclinic.com/Appliance-Parts?s=t-shv46c03uc-%3d%3dc226 ... Bosch Dishwashers

Detergent dispenser Our detergent dispenser is broken, ie, the catch has broken so the door won't stay closed - where can I find a replacement part? thanks!


Here is a link. Sears.com as almost any part for anything including diagrams. The pricing on the part seems WAY out of range. Usually dispensers cost around $60.00 At least you can find the p/n and google around for it on some other sites. I can ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1144 seconds