Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

Electrolux ls6 e3 fault code

\015 No heat and e3 fault i think bottom tank heater or thermister\015

Answers :

Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux ls6 e3 fault code


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Electrolux dishwasher shows code 10 not filling fault and code 20 not draining fault but when running you are able to hear it filling and draining. Whats the problem.?


I had the same issue (Electrolux ESF 6251). I had both error codes 10 and 30. I found that the short hose connecting the inlet valve (solenoid) to the tank was cracked. That explained error code 30, but even after replacing the hose I still got error ... Electrolux Dishwashers

ELECTROLUX WT60E fault code C8 - Electrolux Dishwashers


... Electrolux Dishwashers

My Electrolux 66010 dishwasher stops mid cycle with fault code 60. What does this mean? This code is not listed in the manual. Thanks.


... Electrolux Dishwashers

I have an electrolux dishwasher dx302wj*03 model. The fault code 50 is showing. Does this mean the control panel is faulty or the pump needs replaced? We have been able to fix other problems our selfs from the past and we have avery good store to get all the electrolux parts.


... Dishwashers

Electrolux Dishwasher DX403SJ - 30 Overfill fault but unit is dry. Overflow sensor intact and all looks good. Think we need a reset code. Can anyone help?


... Dishwashers

C3 fault code on electrolux wt55 pass through


... Electrolux Dishwashers

A1 fault code - Electrolux 24 in. ESI6220X Free-standing Dishwasher


... Electrolux 24 in. ESI6220X Free-standing Dishwasher

C2 fault code on electrolux wt55 pass through


... Electrolux Dishwashers

Fault code CD for electrolux ex600 dishwasher


... Electrolux Dishwashers

Electrolux ESL 6251 dishwasher, fault code '30 with continuous warning tones.Is there any advice on what can be done other than calling Customer care as per manual.


... Electrolux 23 in. ESL624 Built-in Dishwasher

Electrolux wt55 Fault code A1 - Dishwashers


... Dishwashers

Electrolux ESL 6251 dishwasher, fault code '30 with continuous warning tones.Is there any advice on what can be done other than calling Customer care as per manual.


... Electrolux 23 in. ESL624 Built-in Dishwasher

Electrolux dishwasher my dishwasher frequently shows fault code 20, what does that represent? Is it economical to fix?


... Electrolux Dishwashers

Electrolux 1113312-20 Hi - my dishwasher circuit board has burnt out (melted) and i need to replace this section. The details on the unit state:- Computime CODE: ELE4157 Electrolux CODE: 1113312-20 Hardware CODE: 156050732 SW: DMA24_MR 230V/roHz T65 Date: 09-281 Can anyone help to advise the best place to get one


... Electrolux Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Fisher & paykel dishdrawer ds605 f7 fault code. Lid failure. This is the second code (after F9- power controller fault).The lid of the dishdrawer will not raise and release the drawer. The lid is stuck in the down position. Assuming this is a power/electronic controller fault. Part numbers would be good.


You can force open the drawer without causing any damage. The actuators on each side will let you do that. But you push it back in unless you manually move the actuators for which you will have to take the drawer out of its housing.\015\012 ... Fisher and Paykel DS605ZW Dishwasher

Fault code hotpoint dwf70 dishwasher has a recuring fault code al99 , what dose this mean. thx kev


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Kenmore Elite dishwasher won't finish cycle. I have the same model, problem, symptoms, and fault codes as in thread: http://www.fixya.com/support/t7120066-kenmore_elite Model: 630.16303401 Fault code: H The water at the faucet is hot: 120F I pulled the control board and all the solder joints looked good--there were no signs of burnt solder joints, missing solder, cold solder, etc I measured the current on the grey-black wire at less than 1 (one) amp when the t-shoot says it should


Hello\015\012& Welcome to FixYa\015\012\015\012If\015\012the water inlet valve is fine then it can be a shorted wire or the heating\015\012element itself that is bad and needs replacement. Please get back to me if you\0 ... Dishwashers

Intake drain flashing - but this time because water is not filling. Checked voltage at controller board - inlet solenoids are getting 120V intermittently. I found online that this is the behavior for fault code f12. But my machine does not give fault codes directly - is there a way to get it to "blink" them?


... Miele 24 in. Incognito G843Vi Built-in Dishwasher

Whirlpool ADG957 Fault Code: first and third lights on and fourth light flashing along with start button light flashing. I know this is a fault code but don't know what it means.


... Whirlpool Dishwashers

Hello, dishwasher whirlpool ACP 4738 display fault code fb (f6 ?) after 3 minutes run. Do you know what fault code means ? Thank's DT


... Whirlpool Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Our Asko 3530 dishwasher is giving us a 'water inlet fault' code. The machine goes through the pre-drain at cycle start then begins to fill, continues until it's full then kicks out the fault code. I have changed the inlet valve, reset the system to factory default and taken off the lower front panel, finding the overflow area to be dry. Is it time to call for service or is there something else to try before spending the big bucks?


Hi,This sounds like either the overflow sensor or the water control valve is stuck.Usually the valve is a solenoid valve that controls the entrance and fill of the water. If the overflow sensor is underneath, there may be wate ... Asko 24 in. D3530FI Built-in Dishwasher

My Kleenmaid dishwasher stops working after couple of minutes and shows fault code D05. The fault explanationd in the dishwasher manual is "D05 fault - motor under load". Any ideas... Thanks Palma


This means the motor is overheating.Remove the unit and be sure there arent dust bunnies collecting around the motor.Clean really well - and re-try.If the error persists - your only option is replacing the motor.Thanks! ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0352 seconds