Having problems with your Hobart 24 in. LXIH-3 Built-in Dishwasher ?

Winterizing a LXIH Hobart dish washer

\015 We are shutting our Lodge down for 3 months and need to winterize the dish washer. Will probably get down to 0 degrees. It is hard piped in and would cutting the pipe and draining be enough. \015\012thanks, Joe\015

Answers :

Joe - The main issue is that the builtin booster heater is full of water - it has to be drained - there may be a small drain plug (square-shaped head), if not, you may have to pull loose the heater element to drain the tank. I would pour antifreeze solution in there and also in the wash tank. Unhook the water inlet - you say the machine is hard-plumbed in but mfgr recommends using brauided water hose to connect to water supply. hopefully this helps - I service commercial machines and came across your question and maybe you can ansqwer one of mine - how do I cancel the "delime" indicator? I can't find operators manual. jimmy.
Hi i am a hobart certified tech the only way to cancel your delime is to cancel this function in the service mode. also you must crack open the fill valve on parker valve and let the water leak out of the bonnet or the valve will split when it freezes
Repair Help & Product Troubleshooting for Hobart 24 in. LXIH-3 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Winterizing a LXIH Hobart dish washer


Joe - The main issue is that the builtin booster heater is full of water - it has to be drained - there may be a small drain plug (square-shaped head), if not, you may have to pull loose the heater element to drain the tank. I would pour antifreeze ... Hobart 24 in. LXIH-3 Built-in Dishwasher

HOBART AM15 DISH WASHER ERROR(E1) - Hobart 29 in. AM15-1 Free-Standing Dishwasher


Are you sure you dont have a bad display, there are no e1 err. for the am15,e2,fill prob.e6sensor,ed,slow leak,ee, bstr not to temp.ef, iternal control err. if it displayed p1 that is an open or shorted wash thermister ... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Hobart glass washer lxi error code e3 - Hobart 24 in. LXIH-3 Built-in Dishwasher


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hobart UX60B Dish washer washer


... Hobart Dishwashers

P1 display on my hobart LXi dishwasher - Hobart LXi Under Counter Dish Machine LXIH-3


... Hobart LXi Under Counter Dish Machine LXIH-3

What does bof mean on a hobart dish washer - Hobart Dishwashers


... Hobart Dishwashers

Hobart lx 30 dish washer does not heat up to temperature


... Dishwashers

We have a commercial Hobart dish washer Model # AM-8T2; Serial # 240461. We cannot get the wash temperature to go above 120' to 150' as the burner does not light. The pilot is on. A new thermocouple was installed but made no difference. The rinse temp goes up to 180'. How can we get the gas burner to light and stay on. Thank you. Gery Spory


Hello Gery - get the repairman back who installed that thermocouple as that repair includes making sure the unit is working properly. Most likely the thermocouple is simply not warming up enough to operate correctly. It may be that the pilot light ... Hobart Dishwashers

Hobart dish washer crs86a electrical diagram


... Dishwashers

We have a some problem .. we working dubai . we have a hobart dish washer model no cl44e serial no 851072177 its workink fine but ther showing probe error fnlsink .. plz send me email ,, what is a salution ....


... Hobart Dishwashers

Where do I find the curtain arrangment and placemant for Hobart c44A, C64A, C66A & C86A conveyor dish washer?


... Hobart Dishwashers

Need the spare parts manual for the Hobart Dish Washer AM 14, ML 110976


... Hobart Dishwashers

I have Hobart under counter hot water dish washer with out a detergent dispenser I'm using Eco lab finish detergent I'm putting in 1/2 table spoon per load and am destroying the finish on my aluminum platters and filling my 18/8 s.s. Flatware Ecolab says finish is safe for all metal surfaces Am I using too much detergent per load


Hi\015\012\015\012 \015\012\015\012Yes you are right, using too much detergent can cause this\015\012issue, use less then half table spoon, if the issue remains then the problem is\015\012with the unit not getting enough water or ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hobart Commercial dish washer - when i turn it on it starts to fill and stops and a wrench appears in the display with EO and it will not run. I have tried to reset the red buttons on the black discs and it is still doing it. Any suggestions on what this could be. Someone please email me back, thank you.


... Hobart LXIC-6 Dishwasher

How do I winterize a Fisher Paykel single drawer dish washer?


... Fisher and Paykel 24 in. DD603MFC Built-In Dishwasher

Doesn't clean well . Leaves food on dishes. - Hobart 24 in. LXIH-3 Built-in Dishwasher


Hi,Check your heating element.. http://www.fixya.com/support/r4589033-dishwasher_problems_heating_element_not\015\012 ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Is this machine high temp hobart h62 dish washer


... Hobart AM14-253 Free-standing Dishwasher

We have a Hobart dish washer in our bar area and when it sits over night there is a pool of water on the floor in the morning. When we open the door and look at the upper right corner in the rear of the machine we have a steady flow of water running down the rear wall. When looking at thge machine where the black 1 inch water hose comes up from the floor there is a plastic T in the line with an electric wire the goes into the side of the T. I am guessing tha that is a sensor valve that is suppos


The model is most likley a lx18,lx30,lx40.The fill solenoid valve is stuck open.Remove the 2 screws on the bottom front where the pressure gauge is.Turn the circuit breaker off.When you remove the cover you will see a bronze valve with a red hose goi ... Hobart Dishwashers

Probe and swich is not working properly.There is four cable, 2 black..its working.other 2 cables Red not connecting.When i short the cable system is working. My hobart dish washer is old I dont know the correct model no.But the part no. is 00-271621 pls replay me as soon as possible I bought a new probe and switch that also same condition.


... Hobart AM15-6 Dishwasher

Hobart lx3 dish washer fills heats and then drrains when wash cycle starts also get error code EO


... Hobart 24 in. LXIH-3 Built-in Dishwasher

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the message. Push reset button and washer starts back runs a couple minutes and then stops and then beep and gives the same message on control panel "washer arm blocked" again. There is "NOTHING BLOCKING" the washer arm!


The rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so \012\012\012\012check the jets for blockages... you might have to remove the arm to clean them properly ... Dishwashers

My Asko D1976 dishwasher is not cleaning dishes properly. There is a lot of clumped detergent left in the dispenser after wash cycles are complete, and many of the dishes have dried-on food left on them. I rinse dishes before loading them into the washer, I have made sure the jets and washer arms are clean, and made sure the food trap at the bottom of the washer is empty, yet the problem persists. I think it has to do with the detergent not dissolving and dispensing. Is there some reason the


First of all, don't pre-rinse the dishes. Check the water temperature, it should be between 120 and 140 degrees. Be sure you are not partially blocking the dispenser door so that it isn't opening. ... Asko D1976 Built-in Dishwasher

I have a Kenmore dish washer model # 363.14051692. This dish washer was working fine and someone stopped it in the middle of a cycle. After that, we can't get the washer to start back up. Where is a reset button on this model, or is there one?


... Kenmore Dishwashers

We have been using this model since Sept. 2007.When new, it worked very well. It has over time, performed less then we would expect. Not only do we have to scrub dishes by hand before placing them into washer,they some times require hand washing after being washed by machine. Not only are they dirty, the glasses are covered with a cloudy white film. We have not done any maintenance or service to this dish washer. Does this washer require some sort of service or attention. Please advise. Thanks


... Jenn-Air 24 in. JDB1250 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1069 seconds