Having problems with your Hobart 29 in. AM15-1 Free-Standing Dishwasher ?

Motor heats up ( to touch )

\015 This happens after running Hobart commercial dishwasher (church use) \015\012after half hour or more continues use for two or three hour event. Do we need a new motor? Don't have model # handy right now. There is also a slight electrical smell.\015

Answers :

Sorry so late,i would check the motor vents on the motor to make sure their not clogged.Any questions let me know.
Repair Help & Product Troubleshooting for Hobart 29 in. AM15-1 Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor heats up ( to touch )


Sorry so late,i would check the motor vents on the motor to make sure their not clogged.Any questions let me know. ... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Kenmore 665.16529000 When we put the dial to pots and pans the diswasher fills up and cycles through, when the dials moves to normal wash, it fills up and cycles through again. When the dial gets to light wsh we can hear the motor running but nothing is happening, but the soap door opens soon after. The heating light comes on and the inside of the dishwasher gets so hot that it has melted our big plastic tumbler cups on the top rack and makes the counter top extremely hot to the touch. The dial


... Dishwashers

Maytag DWU6402AAB dishwasher hums but motor does not run. I've taken the inside apart down to the disk-shaped impeller. It turns freely so the pump and motor are not stuck. When control knob is turned motor hums at the places where it normally should run. The water valve & heating coil seem to be operationg normally. i assume the next step is to test the motor &/or motor relay. Is this correct and how do I do that?


... Dishwashers

I was trying to wash dishes and i noticed that the motor wasn't running but water was filling up the unit. I smelled something burning, and i shut it off and took off the cover and i felt the motor and it was very hot to touch. I assume the motor is frozen. How do I change the motor? Is my diagnostic accurate?


Hi.From your description it sounds like the pump motor has blown and must be replaced.Before replacement the motor can be tested by jumping eac of its wires to energize it directly, for safety reasons the operation must be done by a ... Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

I have Jenn-Air dishwasher that I use the heated dry cycle for. Last night at 11:00 pm or so I ran the unit. Today at 10:00am when I opened the door steam barrelled out and everything was so hot to the touch I gave myself a significant burn when grabbing a non-metal item in the dishwasher. Should I be concerned there is a problem with the entire unit or just the heated dry cycle? Should I be concerned about fire danger due to a short?


... Jenn-Air 24 in. JDB2100AW Dishwasher

I have a KUDK01IL or KUDL01IL that I purchased in 2003 and it went from quite to a very loud wash. Now the dishwasher is not working. Is the motor gone or is something preventing the motor from "kicking-on?" There is water and heat and pannel lights work. Appreciate your help to let me know if this can be repaired or if I should buy a new machine. Thanks.


... KitchenAid Dishwashers

Small Burn spots on interior tub below heating element. These spots have small cracks in center of them, and leak right through the bottom of the tub, dripping water all over under the dishwasher. Nothing has falling into the bottom of the tub, and nothing has touched the heating element. What in the world could be causing this to happen? Kenmore Ultra Wash Quiet Guard 4 Mod.# 665.1603* Purchased new from Sears 2006


Hi,\015\012\015\012The heat from the element when the dishwasher is in the "drying" mode has caused the bottom to stress crack and become open so it leaks...\015\012Ultimately this will cause you to have to replace the dishwasher... ... Kenmore Dishwashers

Kenmore dishwasher 587.15163401 won't fill. I checked the float switch with my multimeter and it's working properly. It's registering zero when I touch the terminals and 1 when I activate the switch. On this particular washer, how do I access the water inlet valve to check it for debris and also to check the solenoids? Also on this particular washer, how do I access the drain valve and solenoid. Can you tell me if this is a single direction motor or reversing motor. As I understand


The problem was the water fill valve. When set to Ohms, the multimeter never would read zero indicating a problem with the water fill valve. I replaced the part and it works now. Be sure to turn your water off under the sink before taking it off t ... Dishwashers

I have a Whirlpool dishwasher (model DU890SWKQO). I turned it on and for a few minutes only the motor was running, no water. I opened the dishwasher to stop it and turn it off, then on again. When I opened it, the was an odor (burning or heat smell) and it was foggy (steam or smoke, not sure which) inside. I am assuming I did not turn the dial correctly so it only 'clicked' on the motor. Concerned now that the dishwasher is broken or concerned that it's not safe to use. Was the steam/smoke


... Dishwashers

The pump motor seems to be jammed on my GE Model GSD2000j I was gone for a few months and it stuck on the 1st wash when I returned. The motor will not turn freely and is buzzing and heating up . Can I free it, lub it, or replace it ?


Dishwasher motors are susceptible to getting stuck if not used regularly. Manually spin the motor to free it up. Dishwasher motors are not serviceable and must be replaced if found defective.But try to access the bushings/bearings and put a few drops ... GE GSD2000J Dishwasher

I borrowed my friends pressure washer and it was working when i had it but she says its not now, could u tell me what u think it could be please. Could it be a motor problem and if so can u explain how a motor would go without me touching it as i dont like the idea im being acussed of breaking it when it was working when i gave it back


The water has emptied out of the machine in transport you may have to bleed the air out of the pump ... DeVilbiss Pressure Washer Hose 25' 38" Id Rubber Has

Water pump I have a porter cable pressure washer model# 2425. I let my presure washer in the garage during the winter(no heat) and now i have a probem with the pump. I start the motor everything is find but when i put the water in the motor stop. Can you help me


... Pressure Washers

Kenmore Model 665.1703 clean light flashing. toggles sani-rinse and heated dry buttons. turned on but motor not spinning. Motor or start capacitor?


... Kenmore 24 in. 17032 Built-in Dishwasher

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Maytag diswasher MDB6600AWW Sprayer arms don't spin. Dishwasher makes all the right noises, except for spraying. Water fills properly and heats up. Water drains properly. Found paper on the back of access panel. Ran Manual Function and Field Service tests, no problems indicated. Disassembled all the pieces inside the bottom of the dishwasher. No obviously damaged parts. Shaft for motor turns freely. It seems like the parts that attach from the impeller to the motor shaft don't


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Maytag dishwasher model #mdbh979aww3 no lights except when you push options found tech sheet put in test mode and all lights worked. removed touch strip from board and drain motor came on after 5 se


... Maytag Dishwashers

Knife touching heating element in water, began smoking


A complete model number will help immensely, please...unless the knife cut through the outer shell/covering of the heater element, or melted to it the worst its gonna do is be really hot.. disconnect from power and remove the kick panel b ... KitchenAid Dishwashers

KitchenAid KUDMO1TJ has a humming sound and think the motor or pump is locked up. how do i check if this is the problem? The dishwasher fills, heats, and drains without ever washing/spraying the dishes. The dispenser still has soap in, the lid does open. I would like to know how to remove the pump. Please give us your expert advice.


... KitchenAid Dishwashers

Follow-up I've removed the lower arm, I'll spend some time and see whether I can get the pobem sorted out. My wife noticed the the detergent was smeared all over the door and repeated tries didn't get it out. Therefore, the water is not spraying. I can confirm the water is filling on the bottom and draining. The heater is working well. I am thinking there is no pressure to send the water through the tubing to the upper and lower arms. The motor is hot to touch (118 degrees with my temp probe). I


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

The spray arm and trap on my Frigidaire dishwasher model #GLD2250RDC2 keep popping off while the dishwasher is running. Now, both pieces have burned/melted areas from touching the heating element. Can't figure out how to properly secure the arm and trap into place to prevent it from coming loose.


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0723 seconds