Having problems with your Hobart 29 in. AM15-1 Free-Standing Dishwasher ?

Hobart lx30h rinse additive is running all the

\015 Hobart lx30h rinse additive pump is running all the time\015

Answers :

The main cause is the "anti flood" device at the bottom of the washer that detects a water leak "hose leak" etc. This device made up of a polystireen float and micro switch is a safety device and when activated puts the washer in pump out mode only. You need to look at the base of the washer and see if water leak has caused this. Rectify the cause "normaly hose or clamp" and this should clear the
Repair Help & Product Troubleshooting for Hobart 29 in. AM15-1 Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hobart lx30h rinse additive is running all the


The main cause is the "anti flood" device at the bottom of the washer that detects a water leak "hose leak" etc. This device made up of a polystireen float and micro switch is a safety device and when activated puts the washer in pump out mode only. ... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

Running a Hobart LX30h as a low temp sanitizer


I can not verify this so DO NOT do this until you find out for yourself!\015\012 I am told that you can actually change the settings on the control panel to the LX40 mode by jumpering J1 and J2 then and then use the up down arrows until you see ... Hobart Dishwashers

Hobart lx18 no power to detergent pump, during the wash cycle there is no power present at the connections for the pump, during the rinse cycle the sanitizer terminal will pulse power and the rinse aid and sanitizer pumps will run, is the relay board bad? With the top drawer open and running the led for detergent never lights up during the wash cycle.


You have to go into program and activate the detergent pump.sounds like somebody deativated the det. program ... Hobart 24 in. LXIC-5 Built-in Dishwasher

For over six months our dishes (especially glass and china) aare covered in a gritty, darkish material. We often have to rewqsh or hand-wah these items afterwards. We have tried numerous rinse additives, run the dishwasher empty, rinsed 2 or 3 times, and disconnected the hose from the drain and run it into a bucket to see these fine particles. I remved and cleaned the bottom filter a month age. It was mildly dirty (not clogged or filthy) but no improvement was seen. Any suggestions? The dishwash


I would guess that you run out of hot water in your house pretty quickly. if so, your water heater tank needs drained. hook a hose to the bottom outlet on the tank. shut off the cold water supply to the tank. open up the hot water on a nearby sin ... Dishwashers

Hobart LXI you seem to know a lot about the hobart, maybe you can help me. My hobart Lxi high temp is just now out of warranty, i am mechanically inclined, and need to adjust my detergent and rinse aid pumps. How difficult is this and how can i go about doing so. Both the pumps are running too much product.


Question--As of today if you look at the display does it read add detergent or add rinse aid?Im asking you this because theres a chemical pump circuit board that senses the chemicals on this d/w.And if the d/w displays those the d/w will keep dumping ... Dishwashers

Hobart low rinse pressure - Hobart Lx30h Commercial Dishwasher


... Hobart Lx30h Commercial Dishwasher

Tank temp Our School Dist. has a Hobart dishwasher Model AM 15 T. After filling the unit it reaches a tank temp. of approx. 160 F, but when it is run through a couple cycles the temp. falls below 140 F, the min. wash temp is 150 F. The supply from the hot water tank is approx. 140 F. The rinse cycle reaches well above the 180 F min. Is there anyway to adjust the tank temp. on this model or could you suggest a solution to the problem. Thank-you John Fry


Check to see if your element is scaled up or your element may be damaged ... Hobart AM15T Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Lxi hobart not pulling rinse aid i used a screwdriver across prongs on board to make it run manually but still not coming out


Try replacing the "squeeze tube" inside the dispensing unit. Over time the tube flattens out. If the tube is flattened no chemical will be drawn from your jug.\015\012\015\012Disconnect inlet and outlet hoses on rinse aid dispensing uni ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hobart lx30h built in dishwasher when you turn it on to wash it shows p2 then it says fill but it want fill up with water also do you run cold water line to washer or hot water


The supply to the d/w should be at least 120degrees.the p2 error is a bad booster probe. always use hot water feed ... Dishwashers

Hello sir i have got hobart dishwasher it doesnt run but it rinse what shall i do it


Possible that the program controller unit is faulty. The outputs to the motor must be checked during the wash cycle and if it is absent even after water has filled in then the controller unit can be faulty. ... Dishwashers

My Bosh dishwasher now runs well past the 105 minutes as stated in the manual, over three hours before I intervene. It gets stuck on the wash mode, it wont drain or rinse, just runs and runs in the wash mode (I know it's in the wash mode because when I open it up, theres suds inside). It will do the wash mode until I reset the wash mode to "Rinse & Hold". I appreciate whatever information you could provide.


Hello, welcome to Fixya.\015\012\015\012The problem you're describing is unfortunately a common one with B/S/H/ built dishwasher's. That includes Bosch, Thermador, Siemens, and Gaggenau. ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Hobart SR24C won't run


... Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.


I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher

Our Maytag dishwasher has all of the sudden stopped rinsing the dishes. The machine sounds like it is running but no water is flowing. The wash cycle runs but not the rinse. Any clues as to why


Check inlet water supply for free flow. check strainer for blockage. Strainer is located at the machine body water inlet tube entry side. ... Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Model-dd6055fd bottom draw does not complete all the cycles, i have to let it run,shut it off,let it run again and then rinse, rinse is the only cycle that goes off


... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher

Hello, I've got a Bosch dishwasher that is acting really funny. I've had it for 4 years. It's 630 SHE44C06UC model. It powers and I hear it run, but the cycle ends w/ 1 but it runs forever...and doesn't rinse or drain. Cancel drain works, but there are spots. I have rinse agent, it fills, drains, etc. I'm wondering if someone knows how I could reset it before calling a repair man? It doesn't seem to dry either? Any help? Thanks, Steph


Hello,Welcome to FixYa.Based on your description I'd say the issue is with the control...unfortunately.The number"1" being displayed ( on models with ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Hobart LX30 Hey I just bought a Hobart Lx30 and we don't have a power source that can handle the 50 amp requirement. We got it at an extremely good price so we are trying to work around it. I was told that disconnecting the water heater would allow it to work in a standard 120 volt outlet. I did that and now I have another issue. The machine wont run unless the water is 160 degrees. How do i disconnect the sensor that restricts the temp so that I can run the machine at a lower temp?


Hopefully you took the suggestion to run the correct 50 amp 208-240 service to the unit.Converting the unit to an LX30C has a couple of pitfalls. The LX30C is connected directly to the incoming water supply, which should run 120-140 degre ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Hobart lx30 : rinse cycle


The rinse water in a LX30 is driven by water pressure. A solenoid valve, bottom front - gold body, opens up and allows the water to flow.\015\012\015\012If you are referring to the rinse agent pump, there must be NO leaks in the tubing or ... Hobart 24 in. LXIH-3 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1010 seconds