Having problems with your Hobart AM14-253 Free-standing Dishwasher ?

Pressure gauge not in green zone and low temp on booster unit


Answers :

If this runs on three phase, or even 240 single phase, check the electrical service to the unit for loss of voltage.
Repair Help & Product Troubleshooting for Hobart AM14-253 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pressure gauge not in green zone and low temp on booster unit


If this runs on three phase, or even 240 single phase, check the electrical service to the unit for loss of voltage. ... Hobart AM14-253 Free-standing Dishwasher

Odd operation Unit turns on, slowly heats up. When wash cycle starts, temp drops 20 degrees. Unit never seems to drain completely. when cycle finishes, Booster heater temp can drop as much as 40 deg (122F) Heater slowly recovers, but unit never seems to go into rinse cycle.


This unit is a sanitizer, not a full fledged dishwasher. It is designed for restaurants and bars where the primary use is washing glassware. The behavior you describe is normal for this model. The manual can be found at the following link: ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Our Kitchen Air KUDIo1Ilbl6 DW is 6 years old. The dishes are no longer getting clean. It sounds different in the washer. I question the pressure is high enough inside the unit. I ran vinegar through the unit, did not seem to matter. The temp is 140 the pressure from our well is the smae as when we installed about 55 psi. I checked te screen it seems to be clean. Any thoughts


Hi\015\012\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's sp ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

I have a Campbell Hausfeld RBPW1810 pressure washer, It has two detergent tanks. I cann't get either to work. I just purchased the unit in June if this year and this is the frist time I am useing the unit. I followed the instructions (low pressure position on the nozzle) and the detergent came on for two second then stopped (only water then). What am I doing Wrong??? Rich From Alqonquin, Ill


Sometimes thinning the solution will help, but in any case make sure the line from detergent tank to pump is sealed, otherwise it just sucks air. I use a small hose clamp at pump. let us know ... Campbell Hausfeld 1800 PSI Electric Pressure Washer

KUDS02FRSS4 low wash pressure in unit? Washes dishes but not the normal water pressure in unit, all filters are clean


Tear down the lower spray arm assembly to the deck while noting placement and orientation of each piece. There should be a large screen at the bottom that may be plugged with food and water deposits. Soak this screen in hot water, detergent, and whit ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Unit starts with good pressure then cuts down to small stream then goes to good pressure and back to low pressure


... Craftsman Pressure Washers

XL30 Hi temp. Two problems: 1) Hi temp booster not working...worked on and off for awhile, now won't get up to 180. 2) Turned on today and water flooded out. Water overfilled machine, turned off and heard pump drain unit.


To attempt to solve the over filling, clean the probes in the back right corner. Use a green scrubby pad.\015\012\015\012There is also two probes under the front screen. Clean them too.\015\012\015\012As far as the booster not ... Dishwashers

In my bauknecht GSFP Control light blinks and the dishwasher waiting after celin 34591 unit (Water pressure gauge)


... Whirlpool Dishwashers

Hobart LXiH preesure gauge is to low - 7 PSI


Adjust your prv if you screw it in all the way replace it . make sure your new one has a bypass built in ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Low pressure on my 1700 unit


... Karcher 1750 psi Electric Pressure Washer

Low water pressure arms will not spin


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Low oil pressure while car is in idle..check gauge light comes on. I had the oil pump replaced and the sludge cleaned up. The check guage light still comes on when car is in idle and epecially when the car is hot.


Sounds like your oil pump replacement was left too late.sounds like a worn engine due to oil starvation with the previous low oil pressure and sludge problem.to verify the oil pressure you need to fit an oil pressure guage. to ... Mi T M Pump Oil

Karcher K2.26M electric power washer leaks water around the on/off switch and around bottom of unit. low pressure.


Probably your seals are bad and they are leakyng ... Karcher K2.26 Electric Power Washer

My hds 645-4-m diesel unit has a low pressure output on the nozzle,what could be the problem?


... Karcher Pressure Washers

I have a north star 5000 psi and I have low pressure it has what looks like a presure relief on the side bottom and it lets alot of water out when motor is not started and a hole lot when running presure gauge only reads about 600 psi when running Thanks in Advance [email protected]


It is possible that your pressure relief valve is on it's last legs. Call the company at 800-221-0516 and get another one. You may still have warranty protection so ask them about that when u call. J. ... Northstar Pressure Washers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

Hobart lx30H Fuse f1 3.2amp 250vac blown, f1 feeds relay board. No booster temp, pump and sump heater active (OK). Can problem be from other devices that are driven from the low power relays on this board or are we looking at a board failure as the only answer. No skinny on door panel, Can't get access to OEM repair manuals anywhere on line Thanks


Possible bad relay coil ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

My Karcher K2.36 stopped working. I had been cleaning the pathways and with no warning, no peculiar noises, etc the unit motor stopped working. The power was connected, the water was still coming from the wand albeit at low pressure. Thanks.


... Karcher Pressure Washers

What oil does my troybuilt pressure wash use, its 4.5 hp unleaded gas 4500 psi? it just stalled while i was using it looked like oil was low, i have no manual and there was no info on unit so i added 10w-30 regular motor oil now engine wont start?


There is no way that a 4.5 hp engine can create 4500 psi. If you are putting the oil into the engine it would just take a 10w30 motor oil, if you are putting oil into the pump I would have to know what pump kind of pump you have, if the name isn't on ... Briggs & Stratton Pressure Washers

Low pressure from Coleman pressure washer


... Coleman Pressure Washer PW0881800

Troybilt pressure washer low pressure


... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

I have a jackson Low Temp single door model.. I


You may need to clean out your hot water heater depending on how old it is and yes 80 gal should be more than big enough adj. thermostat to the next level ... Jackson 25 in. Conserver XL Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0651 seconds