Having problems with your Hobart AM14C-155 Dishwasher ?
Operation of digital temperature indicator
\015 Not clear as to what temperature is actually measured. Does this always indicate the tank water temperature, regardless of what cycle the machine is running? (I assume it does, but just want to be sure.) The electrical schematic shows thermistors labeled "wash" and "rinse" but there's nothing showing how they're wired.\015\012\015\012THANKS!!.....Lee\015
When the unit is idle and in a wash cycle the wash temp is displayed.If you look inside the tank you will see a white float and a metal probe which is the themometer for the wash tank temp.The rinse temp will only be shown when the display reads (Rinse) and theres a thermistor that screws into the water line near the solenoid valve that measures the temp.
Repair Help & Product Troubleshooting for Hobart AM14C-155 Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Operation of digital temperature indicator
When the unit is idle and in a wash cycle the wash temp is displayed.If you look inside the tank you will see a white float and a metal probe which is the themometer for the wash tank temp.The rinse temp will only be shown when the display reads (Rin ... Hobart AM14C-155 Dishwasher
After interrupting a wash cycle by opening the door, the "start" button indicator will not light when the start button is depressed. (Neither will the "delayed start" indicator work.) The dishwasher will not resume any operation. All other control indicators light when selected. Removing and restoring power to the unit does not clear the problem. The unit is a Jenn-Air model JDB1100AWB.
It is possible that by opening the door mid cycle, the door switch mechanism has got disengaged. Refer item 11 in ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher
I bought an IKEA Renlig DW60 dishwasher about 6 months - the controls are located on the inside top of the door. Ordinarily the dishwasher turns on and three red LEDs on the far right of the control panel light up. On occasion however only a single red LED indicating the temperature of the last wash I carried out will go on (it is always the 50 degree light as this is always the wash temperature I use). When this happens the dishwasher appears to be stuck and will not start when I shut th
Press and hold the cancel button for about 5 seconds. This resets the electronics and gets it going again ... Dishwashers
Hello. I have a Kitchen Aide KUDG255HWH1 that will not start from a cold state. The "Energy Saver Dry" and "Normal" indicator light/ switches failed to operate about 1 month ago and since then I have needed to use the "High Temp Wash" and Soak & Scrub" cycles to get the unit to run. Now these two indicator kight will illuninate but the unit will not start when I depress the "On" soft switch. When I depress the cancel switch the unit starts with what sounds like a pre-start cycle. Pleas
Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. To reset the dishwasher switch\015\012off the dishwasher from the power socket and mains for five minutes and then\015\012switch it back on. If still the issu ... KitchenAid Dishwashers
Dishwasher inoperative The lights that indicate the wash cycle are flashing along with the 6 hour delay light. I have tried to cancel the cycle but it does not work. I shut off the breaker to try and reset the operation and that does not work. The dishwasher will not work and I cannot reset or cancel the flashing operations. Kenmore Quite Guard 3 Model 587 15072200
... Kenmore 15522 Built-in Dishwasher
We have a Katcher HDS 3.5/30-4 M Ea. Was using it, stopped using it briefly in the middle of a job, pulled trigger again, and there was a lack of pressure. Went to the machine to troubleshoot. The "engine indicator light" is on. Checked the temperature of machine: fine. Water intake: fine. We have not been running it at high temperatures, but about 50 degrees C. The pressure was at about 2300 PSI before it stopped. Any ideas?
... Karcher Pressure Washers
Diswaher will not operate. The Clean indicator
Change control board ... Dishwashers
No indication of power to console. no operation.
Nothing is simple when checking dishwashers. If you have no function at all when you press run then most of the time the board is faulty.Often the odor you smell is the transformer on the board or other components having gone faulty. Would suggest y ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
My ASKO 1805 Dishwasher started to smell weird and white smoke came from it. I turned it off, but after I turned it on again it just keeps pumping water in and out, I can't get in contact with it (None of the indicator lights are working and it is not reacting to any commands) In addition the safety feauture that is supposed to stop all operation the moment the door is opened is no longer working. (i.e. even with the door open it is still pumping water) Does it sound like an expensive repair? (
Hello,\015\012\015\012Welcome to FixYa. Based on your description ( specifically the white smoke and smell ) I would suspect the control board is faulty. \015\012\015\012If the unit does not stop when the door is open can be r ... Asko 24 in. 1805 Built-in Dishwasher
I have a Hotpoint Aquarius FDW 20 dishwasher. Prewash and Wash lights were flashing, machine had stopped and water was at the bottom of the machine. What does this indicate? After removing some debris from the water drainage pump, then reassembling the machine, I now get the pre-wash LED flashing and a motor operating, but no futher progress into the wash cycle. What does this mean?
Dishwasher always full of water at the end of cycle ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
The F4 fault code on my Fisher and Paykel Dishdrawer Model DD603 dishwwasher indicates that the "temperature sensor is faulty. Question: where is it located on the machine and how do I replace it?
The temperature sensor is located on the heater plate(looks like a blob of solder with a thin line leading to a blob of solder,The solder acts as a fuse when it "blows"you have to replace the heater plate.The heater plate is located in each draw (ge ... Dishwashers
Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me
Kenwood dishwasher KDW 12ST3A is showing E3 after being in operation for about 30 minutes and we have misplaced the manual instructions. can you please tell me what E3 indicates as there was smoke and a smell of burning rubber coming from the machine last week but none since.we always use a P4 cycle
Whirlpool GU1500 dishwasher - no wash cycle buttons would turn on (no indicator light/no operation), but the Cancel button/2 minute drain function works. Any suggestions?
I had the same issue. If you have a 1100,1200,1500 etc you have the first series of the dishwasher and there is a heat sensor issue. The dishwasher runs and checks if the water heats up by 8 degrees. If the water doesn't heat enough then the washe ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher
Water does not come into the dishwasher. can hear the pump, the heater works, the indicator lites illuminate, but water does not come in. The water supply is hooked up and turned on, there is good flow to dishwasher connection, but no water inside the dishwasher during operation.
Hi,\015\012Usually the problem is the soleniod valve that lets the water into the dishwasher...\015\012\015\012here is a tip that I wrote that gives many more details about this problem...\015\012\015\012Dishwasher ... Dishwashers
Model KUDI24SEWH2 - the dishwasher was operating, I opened the door to add another dish. When I closed the door, there was a small click and nothing happened. The lights indicated to me there was rinsing and drying going on, but in reality, nothing happened.rn We were told it might be the thermal fuse, but have just check that and it is fine. It will fill, just not pump or drain. Any help?
... KitchenAid Dishwashers
No heat up of water or any temperature raise . Dryning not in functing either . Heating element without voltage supply, during normal sequence of operation. Has found relay Eberle with part no T-nr 3940620 in investigation of electrical loop. Please come up with a possible malfunction . Thank you very much Best regards Erik Rasmussen
... Miele 24 in. G665 Built-in Dishwasher
The dishwasher will not operate. Some of the blue indicator lights on the control panel are blinking, and I can not get them to stop, by using the Cancel button. Is ther a reset somewhere on the machine?
Turn off the power at the fuse or circuit breaker for one minute. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher
Normal wash cycle runs 2-1/2 hours instead of 1hour 20 minutes as indicated in the manual. Temperature of water going in is 132 (manual says it should be 120 min).
Hello there:\015\012\015\012 \015\012 If the cycle doesn't complete, check these: first ok\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012\015\012\011\015\012 ... Dishwashers
What temperature does the Meiko FV40.2 operate at please?
1)for washing it will work at 60 deg\015\0122)for final rinse at 85 deg. ... Meiko FV 40.2 Dishwasher
Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens. So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e
The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher
Zanussi Dishwashr ZT 695. Only the on/off button will work. The machine fails to start or fill up. None of the indicator lights operate.
... Zanussi Dishwashers
My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light
Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers
Hi we have a westinghouse 921 Freestyle dishwasher and when we turn it on it just cycles through the wash indicator lights. Nothing is displayed on the digital panel and pushing the buttons seems to do nothing.
My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem
The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher