Having problems with your Hobart AM14C-155 Dishwasher ?

The water fills slow and rinse has very little water pressure, I have pressure as far up as the celenoid and cleaned the washer wands&nozzles. there's an elbow with a fitting in it and 2 wires.can you tell me what this is and or give advice to a solution


Answers :

Repair Help & Product Troubleshooting for Hobart AM14C-155 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The water fills slow and rinse has very little water pressure, I have pressure as far up as the celenoid and cleaned the washer wands&nozzles. there's an elbow with a fitting in it and 2 wires.can you tell me what this is and or give advice to a solution


... Hobart AM14C-155 Dishwasher

I have a Challenge Xtreme 1800w Upright High Pressure Washer. The proplem is fluctation in water pressure,this even happens when all hoses are removed so the pressure is coming straight from this pump.the vonly way I can describe it is as if it is "hunting"ie high pressure then a ver short pause then back to high pressure. thank you for any advice you can give me with this proplem,also can you recommend a more suitanble machine for home use. Regards M rA C O'Meara


... Pressure Washers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

After starting my dishwasher ADG 9340/1 (any program) and after pumping evt. (rest)water , the machine won't take fresh water in and gives an acoustic alarm ! After opening the dishwasher , I can see that the "Start"-led is blinking in sequences of six blinks . Can you give me please, a possible cause and/or solution to this problem !


... Dishwashers

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

Jet of water from a bent-elbow fitting when pulling gun trigger


The elbow may be cract insight, try to open it, but first diskonect it from power jet. ... Karcher 2500 PSI Pressure Washer

I have a EuroTech dishwasher Model# EDW254E/SB. It was working fine but now it gives the Err code:er1 Its not letting incoming water in i know that. As well I have been told to try reducing the water pressure at the facet. Did that nothing.It drains but wont cycle to the next stage and let water in. I am presuming there is a valve of some sort not opening? And does the dishwasher have to be completly romoved to fix. Thanks


Hi and welcome to FixYa. I am Kelly. \015\012\015\012This is a water level sensing problem. Look inside your lower wash tub area and see if you either see a circular device off to one side or a finger like device sticking up about 2 inc ... Dishwashers

I have a Dewalt 3800 pressure washer fitted with a 67DX39G11 pump. Started unit up for the first this year, has pressure for 15 seconds then nothing. Water is flowing through okay, everything seems in order but no pressure. Unit is 2 years old but has only 15 hours of total running time. I think the pump has failed, is it normal for a pump to fail with only 15 hours on the clock?


... Dewalt 3800 PSI Pressure Washer

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Kskarcher k 320 ,replaced the elbow inlet and after that it does not work . with water connected the stream of water comes when the trigger is pressed but no pressure or the pump does not start . Any


... Karcher Pressure Washers

How do you remove the plastic internal fitting from the casting to replace the water inlet elbow on a karcher 440 power washer


... Karcher Pressure Washers

What fitting is needed to connect the water line to the back of the dishwasher. It has a plastic 3/4 or 1" pipe thread (I think) out the back side. It came with a standard brass elbow, but it seems to be missing a fitting to adapt to the plastic threads


... Haier ESD210 / ESD211 Built-in Dishwasher

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a


If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

How do i get the pressure washer to pull up cleaning solution into the suction line so that i have a water cleaning solution mix.


... Briggs & Stratton Pressure Washers

Lg dishwasher model LD-2163SH problem code IE meaning water is not supplied. I have checked that the valve is open and water line has sufficient pressure. Inlet hose is also not kinked and pump for drain is functioning normal. Pl suggest solution urgently? manoj


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

I have a Bosch SGS43A22 Dishwasher approx 8 years old. When I start a cycle it fills, runs for about 15 minutes, then drops out about a litre of water from the bottom of the door, then completes the cycle without any more leaking. I have run the machine with the front panel off and can see that water bypasses the top of the seal and fills the well of the seal then pours out. It only happens the once. The seal is fitted correctly. Any solutions?


After 8 years service the seal may have perished, so you should feel for a crack by stretching the rubber where you noticed the leak. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a GE GSD2000J01WW Dishwasher in a building with low water pressure. The inlet hose is 3/8" OD. The heating coil gets too hot and gives off a bad odor as there is not enough water at start up. Is there a way or a replacement part that can be used to change the timing of the heater and wash cycles, etc.? Thanks


... GE GSD2000J Dishwasher

LDS4821st won't fill with water. It is new and I am installing it. I verified I have plenty of water pressure to the elbow for the DW inle?


... Bosch SHU3306UC Built-in Dishwasher

This is the 2nd time I've had problems with my dish drawer. After I cleaned the filter and replaced it, I had standing water on the bottom of the drawer. The last time this happened, I had someone come to repair it - ended up it was me. I didn't put it together properly. This time I did the same thing I was told to do. I still have the standing water. What should I do. By the way, the coils are not kinked in the back either. Can you please give me some advice? Please respond to me at F


Unfortunately I have to respond to you through this post per policy of fixya.com. This s to ensure we have a visibility on the quality of the solution and also allow other consultants to help if necessary.\015\012\015\012Water standing a ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

Hi My dishwasher DS603 has a fault of F1 code beeping for the whole day. I have no clue that dont know how to do with it. It is not flooding however. I dont know if it has problem due to the water wasnt supplied this afternoon as the pipes are repairing outside. Now we got water supply back and it keeps beeping. i tried to dry it ALL UP but it still beeping. Please give me advice! cheers


... Fisher and Paykel 24 in. DS603H I Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1976 seconds