Having problems with your Hobart AM15-5 Dishwasher ?

The solenoid valve of the AM 15, is it the diaphram or piston type and what is the size of the valve


Answers :

Repair Help & Product Troubleshooting for Hobart AM15-5 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The solenoid valve of the AM 15, is it the diaphram or piston type and what is the size of the valve


... Hobart AM15-5 Dishwasher

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

Kenmore model 665.17609300 type 575-0 Dishwasher will not drain. Float valve and drain solenoid ohm out correctly. Drain hose is clear. Suggestions?


Check your air gap on your drain. It should be located on or around your sink. Sometimes food and other trash will stop it up and will not let your dish washer drain. The cap should unscrew off .Good Luck. ... Kenmore Dishwashers

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

Hi my name is rod im trying to repair my friends washer i replace all the orings i would like to no what type of oil goes in with the spring valves & if their is some type of timming mark valves seam off


Hi Rod,\015\012Actually, no should be know. Just about any oil will do. The second part of the question is not clear to me. ... Karcher PSI Electric Pressure Washer

DW fills up with water after sitting. When I turn off the water supply it does not fill up. Removed solenoid valve and cleaned the filter and check for possible blockage. Put back together and turned on water supply. did not fill up until we used it for the first time after my fix. Could the solenoid valve not be sealing off completly DW is a Bosch SH5316UC/U12


... Bosch Dishwashers

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

Kenmore dishwasher 587.15163401 won't fill. I checked the float switch with my multimeter and it's working properly. It's registering zero when I touch the terminals and 1 when I activate the switch. On this particular washer, how do I access the water inlet valve to check it for debris and also to check the solenoids? Also on this particular washer, how do I access the drain valve and solenoid. Can you tell me if this is a single direction motor or reversing motor. As I understand


The problem was the water fill valve. When set to Ohms, the multimeter never would read zero indicating a problem with the water fill valve. I replaced the part and it works now. Be sure to turn your water off under the sink before taking it off t ... Dishwashers

Solenoid Vater Valve or Aqua Stop Valve


On your model the aqua stop valve is the root of what is causing the leak, the check valve inside the aqua stop is reducing the pressure too far and the seat on the water inlet is bypassing due to the aqua stop.So to repair this order the ... Bosch Dishwashers

Kenmore dishwasher type 573-D, model 665.16034402. Items on top rack don't get washed. Items on bottom rack are washed fine. Appears top sprayer and maybe middle sprayer aren't getting water. At rear of washer, top rubber flapper valve (which feeds middle sprayer when top rack is in raised position) is stuck open, bottom flapper valve looks OK. We use top rack in raised position so this doesn't seem to be the problem.


... Kenmore Dishwashers

I have a shx46a02uc / 21. I rebuilt (cleaned) the water inlet solenoid valve because valve was stuck open and kitchen and basement flooded. That problem is solved. However, the dw is in mid-cycle s


... Bosch Dishwashers

I have an MTD Honda powered mower 187 cc. vert shaft made in Canada, I freed the carboned exhaust valve and went to reassemble but didn't pay attention to the valve timing. Anyone know where to put the cam compared to the piston? Any timing marks any where,I can't see any. Thanks


... Pressure Washers

I have a Kenmore dishwasher 665.17799990. Not enough water was coming in so I thought that I'd check the screen inside the water inlet valve to see if it was clogged. It was. I cleaned it out,but mistakenly opened the wrong part of the valve looking for the screen and took apart the diaphram assembly. Bad mistake. Now I can't get it back together without it leaking like crazy. I can't remember how it was configured to start with. I put it together once,but it wouldn't shut. I can't afford to buy


... Dishwashers

Miele dw flashes 5 times, water is draining. Suspect filter/valve housing at end of water inlet line. Their is a wire running to this valv so I imagine whatever solenoid that tells the valve to open and let water in is not working. Am I close? I cleaned inlet filter.


Which light is flashing? if the intake drain light is blinking and you dont hear the drain pump, it means water is not coming in. if the drain pump is running all the time, it means water has leaked into the bottom pan. behind the plastic toe ki ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

6.5 hp briggs on power washer, the intake valve is opening on the up stroke of the piston and like wise with the exhaust valve opens on the up stroke, engine will not start


... Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

I just purchased a Simpson Megashot V3000 Pressure Washer and noticed the engine would stop running every time I released the wand trigger. Also, water was constantly spraying out of a valve underneath the unit - I assume it's some type of pressure release valve but there is no mention of it in the owners manual. I am thinking about returning it to Costco for a refund.


... Simpson Pressure Washers

Water vALVE DOES NOT QUITE SHUT OFF. AFTER WASH COMPLETED, water leaks slowly into tub and overflows onto floor. iT IS TYPE 1353-1. wHAT IS PART NUMBER FOR WATER VALVE? pRICE AND WHERE i CAN GET ONE? tHank you Kenneth Oag


Hello,\015\012If you can supply the Product number or model number I would be able to help.It would not be a major expense for a new inlet valve.Check if the drain pipe from the dishwasher if going into a pipe outlet in wall that it is not too ... Dishwashers

I have a Maytag dishwasher and the power is not getting to water valve(solenoid) it comes straight from timer(pin 29) solenoid works with 120v applied


Check you float,is it stuck up it should lift and drop freely. if thats ok and the wires are fine your timer is probably bad. ... Dishwashers

Asko Dishwasher DW20.1 d3120 Water not coming through inlet valve. I have replaced the inlet valve - solenoid only releases when on/off switch and start button are pressed and released simultaneously. A burst of water comes out at that point and stops. What could be wrong?


Hi, Welcome to FixYa.\015\012\015\012I'll start by saying your description sounds exactly like a symptom of a faulty control board on Asko dishwasher's...specifically the relay responsible for energizing the fill valve. It sounds to me like the relay ... Dishwashers

Hobart Sr24h drain valve solenoid constantly energized thought the whole dish washing and rinse cycle. The drain valve/solenoid is new. Is there a control board timer setting for the drain valve?


See the wirin diagram for test and see how to test: ... Dishwashers

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

Dishwasher won't fill. replaced fill valve assy. checked float switch it's ok. timer seems to be cycling properly but i'm not getting power to fill valve solenoid. Is it the timer or advance module? and how do I test?


Since you are this deep into the machine, it would be easy to tell if that is the issue by using a meter to test for continuity THROUGH the switches on the timer. It might be the power supply is not working right to send the voltage to that switch. ... General Electric WD21X10013 TIMER

What size is the o-ring on the plastic check valve? Causing it to surge every 1-2 seconds.


... Karcher K2.26 Electric Power Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0316 seconds