Having problems with your Hobart Dishwashers ?

Hobart conveyor dishwasher model crs-66 serial#286458 2o8-3ph machine is 38 yrs. old. pilot lite would not stay on. changed thermoule coup. when switched to on everything goes off. this pilot valve is completely seperate from main gas valve.


Answers :

I'm a hobart tech,The valve your talking about is the saftey valve.Normally if i serviced your dishwasher i would replace both valves just because how old it is.But in most cases the saftey valve goes bad.The coil on the valve is weak and tends to drop out the voltage.Another thing to check that would cause the same issue is the pilot,especially propane gas.Sometimes you can just clean out the pilot but if it's warped i would replace it.
Repair Help & Product Troubleshooting for Hobart Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hobart conveyor dishwasher model crs-66 serial#286458 2o8-3ph machine is 38 yrs. old. pilot lite would not stay on. changed thermoule coup. when switched to on everything goes off. this pilot valve is completely seperate from main gas valve.


I'm a hobart tech,The valve your talking about is the saftey valve.Normally if i serviced your dishwasher i would replace both valves just because how old it is.But in most cases the saftey valve goes bad.The coil on the valve is weak and tends to dr ... Hobart Dishwashers

I have an Asko Model 1473/1503 with the word excellence on the front door panel. It is approx 14 yrs old. I noticed that the main switch has been failing and that I have had to giggle it about to latch. It has now completely given up the ghost and there is zero power to the dishwasher. The CB is on . I believe I have to change the main switch but I have no idea how to get at it to remove and replace it. Any ideas?


Http://www.repairclinic.com/smartsearch.aspx?SearchText=`Basko&gclid=CLuI1p7BypcCFQwNGgodD3kkSw\015\012 Call these guys, ther may be a diagram on their site, but I have called them several times in the past and they knew almost immediatlly ... Asko Dishwashers

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

All the programme cycle lights come when any programme is selected. I have opened and cleaned the filters, drain pump and non-return valve. I have switched power off at the mains. I have also depressed the off switch for 5 secs as recommended on the Miele website and then re-started the machine. Still get the same error. Any suggestions would be gratefully received.


Hi\015\012\015\012Try and reset the dishwasher by following this sequence---\015\012\015\012Turn the power off to the machine.\015\012Press and hold button 2 and 3 together while turning the dishwasher on. The salt and i ... Dishwashers

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

My Troy Built 2500 psi power washer with Honda engine GCV has been stored for 2 years. I changed the gas and could not get it to start. Which is the start position for the valve on the gas line - Horizontal or Vertical? Thanks, Bill Gray Melbourne Beach FL


... Pressure Washers

No voltage to water inlet valve, overfill switch seems ok and door switch seems ok. I am thinking the timer, but everything else seems to work fine is there something i am overlooking?


\015\012Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU).\015\012Check all hoses for possible leaks.\015\012 ... Roper Dishwashers

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Pressure wsher wont start. added oil to pump resv. its full. changed plug . didnt change gas . been a couple years scince it was started. could it be the little relay or capicitor on side of motor that has wires going to on & off switch


Hi steve_shouse\015\012Make sure you are getting spark at the spark plug, to do this:Remove your spark plug and check to be sure you are getting a bright blue spark at the spark plug.You do this by grounding the plug on the head of the en ... Honda Pressure Washers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

We have the same problem. At first, we were getting a horrible detergent film on everything. We thought that was because the detergent cup wasn't opening or the water was too hard or not hot enough. We kicked up the rinse agent as high as possible, switched to a liquid detergent, and only placed shorter items towards the door. The cup still wouldn't open consistently and our dishes still needed to be re-cleaned. We stopped closing the cup. No change. Why would liquid detergent leave a powder fil


You dont need a new dishwasher. it is your water that is causing the film and residue. go to www.dishwasherfilter.com. they have an awesome product that is affordable and g ... Dishwashers

Whirlpool Dishwasher Model Du850SWPB3 Changed out Water valve, float switch, Still doesn't fill with water. D/w runs in all cycles , just NO WATER.


Hello,What ya need to check is for power coming into the water valve from the control board by using a mulitmeter set to measure ac volts and when the dishwasher is running...during the times the unit is supposed to fill their should be p ... Whirlpool Dishwashers

Karcher washer gas no pressure modele g2600vh part no 11944040 high change the spill valve no pressure


... Pressure Washers

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

Washer won't start tried everything , I could think of changed spark plug tried new gas , Two things that bother me are . if i take out the spark plug and put my thumb over the spark plug hole theres no pressure and the wire that comes from the coil to shut off the pw it has continunity from the coil to the pin that sticks up to shut off the pw but it also has continuity from the coil to all parts of motor.


... Pressure Washers

Bosch dish washers Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 the screen on the machine seems to show not started i can get the info to change if i partly turn off the power switch then it shows the main options , any reset procedure i should follow to put machine in a full reset ?


... Dishwashers

No power on the main switch inside the door, checked the fuse in the plug changed with new and no success, we had 2 poss 3 power cuts yesterday but the dishwasher was not working at the time? christmas time help. not sure on the actual type as it was in the integrated kitchen when we moved in 2 years ago an no manuals.


Make sure there is power coming from the house panel by checking the breaker for the dishwasher. ... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Lamona dishwasher - all indicator lights are on but the machine does not start. Unable to change programme as all lights stay on. Have switched off from the mains thinking that the programme might need to reset itself - no difference.


... Dishwashers

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

HI THERE MY HOTPOINT FDL570G HAS A BIT OF A PROBLEM IN THAT WHEN I CLOSE THE DOOR IT TRIPS OUT THE RCD SWITCH ON THE MAINS BOARD. HOWEVER IF THE DOOR IS CLOSED AND I SWITCH THE TRIP SWITCH ON THE MAINS BOARD BACK ON THE DISHWASHER WORKS FINE!!!


... Dishwashers

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Trips mains fuse when switching on


Disconnect the heating element,remove lower panel and take the 2 wires off the heater and tape.Reset the breaker and turn it on,if it's ok you know the heaters bad if not let me know. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0643 seconds