Having problems with your Hobart Dishwashers ?

Free standing hobart model KDD 60A Serial # 222601715 Washer does not start when door is closed and locked. Electrical power to wall socked operating. Machine plugged in. Water supply connected. Start attempted in rinse cycle and wash cycle.


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or door\015\012lock switch which is not engaging itself. And, if the door latch will not\015\012engage the dishwasher will sense it as open door and will not start the cycle.\015\012The light also blinks when the dishwasher detects a no-fill\015\012condition. You’ll need to get access to the fill valve by removing left\015\012panel, look at back to see where valve is when you get to it remove one of the\015\012wires and set meter to ohms setting and put a lead on each tag on valve. The\015\012reading should be about 3.6k ohm. If there is no reading then the valve is at\015\012fault. I'll also suggest you to check the detergent dispenser\015\012solenoid for this issue. Please do accept the solution if the issue is resolved\015\012or post a comment for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Hobart Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Free standing hobart model KDD 60A Serial # 222601715 Washer does not start when door is closed and locked. Electrical power to wall socked operating. Machine plugged in. Water supply connected. Start attempted in rinse cycle and wash cycle.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or door\015\012lock switch which is not engaging its ... Hobart Dishwashers

Whirlpool PLD2855RFC3 will not complete wash and rinse cycle and sometimes shows a PF trouble code wall plug and power cord checks out


... Dishwashers

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers

Problems with Danby DW1899WP. My husband and I ordered it from Wal-Mart online and picked it up yesterday. We've read through the manual several times, filled all the appropriate receptacles, plugged it in, hooked it up to the water, loaded it, set it, started it, and it doesn't work. It runs the pre-wash rinse for about five minutes before giving a series of beeps, draining the unit, and switching straight to the dry cycle without actually washing the dishes. Help!


... Dishwashers

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

Global 450 dishlex dishwasher. Had the handle replaced 2 months ago. After that the ready light did not switch off as before. Now it only rinses. When you set the normal wash cycle the lights for Pre Wash, Wash and Rinse all come on. Pots cycle, the Pre Wash, Wash, Rinse and Dry all light up together, hence the machine thinks it up to that stage of the cycle. Can this be repaired or not. The machine is approx. 12 -14 years old.


... Electrolux Dishwashers

During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.


I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Several people have posted this problem with the Frigidaire Ultra Quiet 111, but I have seen no solutions. When it is set to wash without extra heat, it cycles normally. But when the extra-heat wash and extra-heat rinse are selected, then it gets stuck first mid-wash at the 7 o'clock position, and if it is manually advanced then it gets stuck again during the rinse cycle just before the 9 o'clock drying position. Both the wash and rinse thermostats have been replaced without solving the problem.


Hi,\015\012\015\012I know that you are going to think that this is dumb... but the only thing that it can really be is the timer....\015\012\015\012 ... Frigidaire 25 in. FDP750RC Free-standing Dishwasher

Hi In the middle of a wash cycle, my dishwasher tripped the circuit breaker on the wall. I diagnosed this by unpluggin dishwasher, plugging in a different appliance and switching circuit breaker back on. new appliance worked OK. When dishwasher had cooled, I tried it again on same circuit (which I knew was working properly). The lights came on for about three seconds, and then the circuit breaker cut back in again, so I knew it was the dishwasher that was causing the problem. Is there anyt


Ck the connections where the cord hooks to the wiring harness. look for hot or shorted wiring . also ck the contro panel for the same . generaly if you have a power draw like you are saying then you can see t ... Dishwashers

Further to my open question for my Asko N516 D5131 SS dishwasher I have been able to successfully press the wash setting cycle, which was before frozen on 'rinse and hold' . I then press the on/off. Button the time shows but as soon as I press it to start the dishwasher the screen changes to three horizontal curly lines and nothing further happens... It won't start. Please , I do hope somebody can give me advise. I cannot get to the power plug as it appears pot be located behind the unit whi


... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

My Maytag Quiet Series 200 Dishwasher Model MDB6600AWW washes the dishes but does not go into it's rinse cycle and does not stop. I have to turn switch off at the wall to get dishwasher to stop. The water is hot and the dishes appear clean but it doesn't turn off.


... Dishwashers

After wash cycle and rinsed cycle there were suds


Make certain you do not use dish soap when rinsing the dishes. Make sure you only use DISHWASHER soap when running the DW.In fact,there is no need to rinse dishes. Remove visible scraps and put them in the DW. If it is a quality DW it will clea ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

I have a Maytag Quiet Series 300 dishwasher model number MDBH955AWW. When I press the wash cycle button it starts and then automatically jumps to the rinse cycle. After going thru the rinse cycle for a couple of minutes, it shuts off. After that,I can push the wash cycle agin and it works. Any idea what could be wrong?


HI. This will be a basic logic chip fault. It could possibly be solved by simply preforming a hard reset. You can do this by shutting down the power to the unit for five minutes. This shutdown will force the logic sector of your electronic control bo ... Maytag 24 in. MDB9750AW Dishwasher

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

The machine fills ,drains and washes as normal. However when it fills the wash temp is 60 as normal but the rinse temp wont go higher than 76 deg C . when the wash cycle is on , the cycle stays on wash not progressing thru drain and rinse What is the cause?


Hello. Let me assist you. There are only two reasons for your problem - if you can isolate your problem based upon these descriptors you will know which part to replace:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Water-he ... Dishwashers

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

501ht goes thru wash cycle but cam stops just before rinse cycle clicks in - stays in wash cycle - turned thermostat to booster down in temp -cam then keeps going properly but with no hot water from booster - replaced thermosat still same result - apparently a safety ? no booster water no rinse?


Did you get a solution for this? I am having the same issue. Please email me at [email protected] Thanks -Eric ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

Hobart lx18 no power to detergent pump, during the wash cycle there is no power present at the connections for the pump, during the rinse cycle the sanitizer terminal will pulse power and the rinse aid and sanitizer pumps will run, is the relay board bad? With the top drawer open and running the led for detergent never lights up during the wash cycle.


You have to go into program and activate the detergent pump.sounds like somebody deativated the det. program ... Hobart 24 in. LXIC-5 Built-in Dishwasher

My Defy Dishmaid Silent makes a loud knocking noise when i start the wash cycle, it fills with water but dose not wash.When i start the wash cycle it sounds like it is washing with the added knocking noise but at the end of the cycle the salt has been released but nothing has been washed.A few weeks ago it would run the rinse cycle but now it will not wash on any of the cycles.Please advise.


... Dishwashers

Excessive foaming when using Rinse Only Cycle in Kitchenaid Dishwasher. I've had this dishwasher only 3 weeks. There is no detergent in the dispenser. Rinse Cycle should be only water; no soap. Rinse Aid should not be dispensing either. What could be the problem? Normal wash cycle leaves residue on glassware. That is why I run the Rinse Only Cycle. I have done this over and over with the same results? HELP!!!


Do you have a softner in the house ... GE 15" Laundry Pedestal for Horizontal Axis Washers and Dryers - White-on-White
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1699 seconds