Having problems with your Hobart Dishwashers ?

HOBART AM3 Dishwasher.(AM3-385) 3phase + n supply.

\015 Has had L3 and N cross at install. fuse 3FU continues to blow.\015\012Who do we talk to re new circuit board?\015

Answers :

Repair Help & Product Troubleshooting for Hobart Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HOBART AM3 Dishwasher.(AM3-385) 3phase + n supply.


... Hobart Dishwashers

I am looking for a replacement chlorine supply tube that includes the anti-syphon (or backflow) ball valve to connect a clorox bottle to the pump inlet of a Hobart undercounter sanitizing dishwasher. In the set-up I have a large clorox bottle standing upright in the undersink cabinet and the supply tube comes out of the top of the bottle to connect to the clorine pump inlet


HelloPlease click on the following website link to locate the nearest dealer near your location to order the replacement chlorine supply tube. ... Hobart SR24C-4 Dishwasher

I am working with a Hobart C44A diswasher with a 15KW water basin heater and a Hobart bosster heater. What is the minimum water temperature I can supply to the dishwasher and maintain 160 rinse temperature required?


Hi,140F min water entering temp.http://www.instawares.com/Prod_PDF/HOB-C44A263.pdfheatman101 ... Hobart AM14-253 Free-standing Dishwasher

Bosch Dishwasher SGS43E02 Exxcel. Switches on at main switch (0 appears in the numerical display) but none of the right hand programme buttons seem to be working! Have checked filter on water supply hose and that doesn't look blocked.


Obviously a faulty connection. Lots of switching off and on and holding down the buttons eventually sorted it! ... Bosch 24 in. SGS43E02 Exxcel Built-In Dishwasher

Hi, ihave a miele dishwashe type G7856. the machine starts, then after a short period of time the light for filling/draining flashes and the alarm F 0 S appears. i have checked filters for water supply and that pressure is present.


... Dishwashers

Hello i have a hobart lx40 dishwasher is it a manual water fill or is it suppose to be hooked up to a water supply?


It needs to be hooked up to a water supply (hot line).\015\012\015\012dont forget the drain.\015\012good luck\015\012 ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Tank temp Our School Dist. has a Hobart dishwasher Model AM 15 T. After filling the unit it reaches a tank temp. of approx. 160 F, but when it is run through a couple cycles the temp. falls below 140 F, the min. wash temp is 150 F. The supply from the hot water tank is approx. 140 F. The rinse cycle reaches well above the 180 F min. Is there anyway to adjust the tank temp. on this model or could you suggest a solution to the problem. Thank-you John Fry


Check to see if your element is scaled up or your element may be damaged ... Hobart AM15T Dishwasher

Free standing hobart model KDD 60A Serial # 222601715 Washer does not start when door is closed and locked. Electrical power to wall socked operating. Machine plugged in. Water supply connected. Start attempted in rinse cycle and wash cycle.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or door\015\012lock switch which is not engaging its ... Hobart Dishwashers

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

HOBART FX-20 dishwasher out of order


There is one glued to the lower panel on the inside. Hobart is very tight lip'd when it comes to getting any info from their web site. Best I can do, sorry. ... Hobart 24 in. LXIC-5 Built-in Dishwasher

Hobart LX 18 problem


You are having a problem with the fill valve. If the unit fills AT ALL, with the power off, the fill valve is the issue.\015\012\015\012It is a gold color valve behind the front kick panel. It has a large castle-like cap. Sometimes debris ... Hobart 24 in. LXIC-5 Built-in Dishwasher

Hobart AMX900-20 Trouble shooting manual


... Hobart Dishwashers

HOBART DISHWASHER AM900 NOT GOING THROUGH CLEANINBG CYCLES


... Dishwashers

Winterizing a LXIH Hobart dish washer


Joe - The main issue is that the builtin booster heater is full of water - it has to be drained - there may be a small drain plug (square-shaped head), if not, you may have to pull loose the heater element to drain the tank. I would pour antifreeze ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a Miele 590G dishwasher. Everything appears to work except for water supply. Any suggestions about what I could do or what could be broken? I opened the supply connection (the small gray box) and checked the filter - all seems good. But still - no water supply! Thanks in advance. Ross


You must to check also the tap of water which connect water to this small box may the water pressur out from tap is weak .\015\012you can use a small pan to help this test.\015\012 thanks ross ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

I want to disconnect the water supply. I am replacing this 12 year old slimline smeg dishwasher and they are coming to take it away to morrow. The connection to the water supply is via a grey plastic box with and electrical sign on it ( a lightning flash with an arrow on the end). Although I have disconnected the eletricity supply (unplugged the cable to the machine) I am concerned about what this bos may be. Can I just unplug it?


Hello Henry,\015\012\015\012It's the aqua-stop safety valve and yes, you can just unplug it. Make sure you close the valve on the water-supply first or it's going to get rather messy!\015\012\015\012FYI, the aqua-stop is a sec ... Dishwashers

Dishwasher won't start. It keeps beeping and has error msg "check water supply". Water supply should be fine, and we tried turning power supply off/on to reboot. But no luck. HELP!!!


... Thermador DWHD94EP Stainless Steel Built-in Dishwasher

Hi there, I have just installed my DX203SK. Conected water supply, waste hose and power supply. Turned it on and there is a noise like its trying. But stop cycle and it is dry. I have tested water and power supply. Please help. Thanks


... Dishwashers

Water supply to my Bosch SHE43CO5UC/17 dishwasher seems interrupted and not being supplied to the unit. Water supply to the unit is checked and confirmed available. What are the possible causes, i.e. stuck solenoid valve?


Could be a dirty hose filter or faulty inlet valve. Ther could be a leak and the bottom of the unit has flooded activating the flood safety which will cut the water supply. The pressure chamber and/or the hose pressure chamber to sumo could be bloc ... Bosch Dishwashers

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers

No water will enter the dishwasher, There is no problem with the water supply or the supply line. The water flows from the supply line to the dishwasher connector but does not enter the dishwasher.


The water-inlet valve lets water enter the machine. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you get power to valve when unit is put into operation ... KitchenAid Dishwashers

Hobart LXI you seem to know a lot about the hobart, maybe you can help me. My hobart Lxi high temp is just now out of warranty, i am mechanically inclined, and need to adjust my detergent and rinse aid pumps. How difficult is this and how can i go about doing so. Both the pumps are running too much product.


Question--As of today if you look at the display does it read add detergent or add rinse aid?Im asking you this because theres a chemical pump circuit board that senses the chemicals on this d/w.And if the d/w displays those the d/w will keep dumping ... Dishwashers

I need to repalce the elctrical supply cord and water supply line to my Fisher & Paykel DD603 dishwasher, but I'm unsure as to how to remove the terminal box cover. Could you please help? Thanks.


THIS IS SIMALAR TO THE BOSCH UNIT, IF THERE IS NO BOTTOM COVER TO REMOVE YOU NEED TO TAKE THE SCREWS OUT OR THE TOP INSIDE THAT HOLD IT TO THE COUNTER TOP, PULL THE UNIT OUT SLOWLY, TURN OFF THE WATER SUPPLY SHOULD COME OFF THE HOT SIDE OF YOUR FEED ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Hobart LXi Dr Op will not turn OFF? Any suggestions before calling Hobart Service??


... Hobart Dishwashers LXIH-4 Undercounter Dishwasher Lxih4

Frigidaire GLD225ORDQ5 dishwasher stuck on wash cycle. Water supply & elec supply is fine, nothing blocking drain or spinners.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0218 seconds