Having problems with your Hobart Dishwashers ?

Hobart Dishwasher We have an old smaller built-in dishwasher at our church (Hobart model WM5H). It doesn't stop spraying water if you open the door to remove a rack of dishes to put the next rack in like it is supposed to. One member thought it may be the Electrical Timer Switch? Would this be a fairly easy repair?


Answers :

I guess I didn't understand your statement of the problem. If you know that the washer has gone through an entire cycle, and it is time to take out the RINSED dishes, yet the washer turns on when you do this, play with the door interlock and the door handle switches. If the cycle seems to have stopped, but you timed it from the beginning of a new cycle and it hasn't done all the steps, and it sprays when you open the door, then you may want to remove the timer motor and clean the contacts/ check for tine damage along with checking the door switches.
Repair Help & Product Troubleshooting for Hobart Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hobart Dishwasher We have an old smaller built-in dishwasher at our church (Hobart model WM5H). It doesn't stop spraying water if you open the door to remove a rack of dishes to put the next rack in like it is supposed to. One member thought it may be the Electrical Timer Switch? Would this be a fairly easy repair?


I guess I didn't understand your statement of the problem. If you know that the washer has gone through an entire cycle, and it is time to take out the RINSED dishes, yet the washer turns on when you do this, play with the door interlock and the doo ... Hobart Dishwashers

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

I have an Ultra Wash II, 665.1675590 dishwasher that works like a charm, my only problem is that when I put a rinse agent in the rinse dispenser, the minute I close the door it all runs out. I can fill it one day and the next it's empty. How can I fix this problem.


\0121 .Cut back on the amount of detergent used during the wash cycle. Sometimes this alone will solve your problem.\012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\012\011 ... Kenmore Dishwashers

Pump problems I had a fairly light load of dishes that needed to run so I thought I'll put some plastic fruit on the top rack to also get clean. Well, when the load was done and I opened the door everything was covered and I mean everything with a whitish substance aka wax! One of the fruit was made of wax an melted all over the entire interior of the dishwasher. We had 30 people now arriving for dinner so I just left it all alone. I should have run it again immediately but I didn't. Now after r


Hi murrie825,\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your problem is: you can't get the pump to drain and can't figure a way to get at it.\015\012\015\012It sure sounds like the pump is clogg ... Dishwashers

Are the top rack adjusters on the Whirlpool GU2400XTP dishwasher an owner-serviceable item? Do most Whirlpool parts stores sell the top rack adjusters for the Adjustable 2-position top rack? My dishwasher is five years old and one of the adjusters has broken. The two-position rack seems like a good idea but the plastic part doesn't look like it was built for high-temperature durability.


... Whirlpool GU2400XTP Built-in Dishwasher

Maytag Dishwasher circa 2002 - Defective Plastic rollers The plastic rollers that slide the arms of the dish rack keep breaking. I have had this dishwasher for 6yrs now and go through 1 a year. This defect is really annoying for two reasons one; the cost - $50 each - X's 6 years = $300. Secondly, the inconvenience of having a delapitated dish rack that crashes sideways - with the weight on only one side. Presently, I'm about to order my 6th one. I'd like to know if you are aware of this d


... Dishwashers

Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are


Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher

16 year old GE built-in dishwasher, model GSD900. Springs that prevent front door from falling disconnected. ALL parts APPEAR to be in good condition. I say appear in good condition because I don't know what they are supposed to look like. But I see nothing obviously broken. The 2 springs appear intact. The connecting cable is good. However one of the 2 springs is shorter than the other. It may be shorter because one is supposed to stretch to the other side of the dw? So number 1


... GE Dishwashers

My Brada portable dishwasher does not clean the dishes very well. Also the racks are very hard to pull out and put back in, very frustrating. When pulling the racks the whole dishwasher moves. I am not very happy with this product. Would never by another one.


... Dishwashers

Maytag My Maytag dishwasher is leaking from the bottom. It is a mdbh940aww. it was never used before. It was wrapped in the plastic wrap when I bought the house in 2005. Now the old one just went and I want to put this one in. It fit nicely, works great but leaks all over the floor. It is level and I check most of the parts. I put a mirror underneath and it looks like the rubber thing isnt looking too good. Do I replace this? If so how?


I also had a mdbh940aww that leaked from underneath. You need to check out where the water is leaking from. Unscrew and remove the bottom front panel so you can view under the dishwasher. Start up the dishwasher and using a flashlight see where th ... Dishwashers

I have a hotpoint built in automatic dishwasher model HDA3740G02SA. When my dishwasher runs all the cups on the top shelf seem to have dishwashing soap powder left in the bottom of the cups. I do not over fill the cup where you put the dish washer powder in. It seems like it isn't rinsing the glasses and cups on the top rack of the dishwasher properly. Do you know what the problem would be and how to correct it?


Make sure the arm on top isnt hitting something, each time you load it each in there and spin it to be sure it moves freely, also make sure your rinse agent container is full of rinse agent. ... Hotpoint 24 in. HDA3740G Built-in Dishwasher

Broken dishwasher It started when my dishwasher flooded my kitchen. I drained it and turned it on, it was fine. then it happened again. I have drained it then when I went to turn it on again it just sounds like it is running with no water. If I put water into the bottom it will drain but it will not fill up. I bought this house 3 years ago I am unsure how old the dishwasher, do I need to get a new one?


I have a kenmore model 665 168 29000 the mounting bracket have broken from under the cabinet, so when you open the door and pull the racks out the machine moves forward, how can i fix this????? ... Bosch 23 in. SHU33A Built-In Dishwasher

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

The flimsy plastic guide wheels on the rack for my (ca. 2000) GE monogram dishwasher have been breaking. Six so far. GE wants $25 - $30 per wheel to replace and $235 for a whole new rack!! I will not reward this rapacious corporate behavior. Is there an appliance graveyard (like an auto wreck yard) where one can get a used rack? Are there wheel manufacturers/suppliers that will sell reasonably wheels of similar dimensions to the breaking wheels? Preferably in nylon or stainless steel, not the cr


We have just solved the problem with our wheels falling off! For .75 cents a wheel we purchased new wheel "clips". The connect straight into the wheel instead of "rotating" on. Big differnence and so easy to change out! 5 minutes and the problem is g ... Dishwashers

Water from my disposal backs up into my hotpoint ($300-model) dishwasher. The dishwasher works fine otherwise. Is there a one way valve in the diswasher that is suppose to prevent reverse flow and/or is there other dishwasher motor problems which could cause this. Actually the Hotpoint Model number is HDA3600N00BB but this website did not recognize that model number so I put in the closest model number closest to mine.


If it's what I think, it's a simple fix. Does your dishwasher drain run along the floor of the cabinet, then up to the disposal? (my guess is yes). There should be an "air gap" between the disposal and dishwasher, this means when it comes out of th ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

The dishwasher is not cleaning. It has left a residue all over the dishes especially colored plastic ware glasses. like it doesn't rinse but i have ran the extra rinse cycle and residue is still there. It has actually stained the dishes. Then ceramic dishes are not clean. And ones on the top rack feel like there is a coating on them that does not come off unless you rinse by hand.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... GE Tritonr XL GSD6260JCC Dishwasher

Hey Everyone! Ok try this one! I have been working on a KUDS25 Kitchenaid Dishwasher. It was leaking like a siv from the bottom. I replaced both top and bottom plastic bearings and also tightend all the screws at the bottom. Leak Gone, I thought. It now has small leaks down both sides. I have since been told by the owner that he took the door apart himself. I pulled out the dishwasher from the cabinet and ran it. I could see the leaks at the top on both sides of the door latch. I cou


Hello davidgalb. You can install a new gasket to seal the door again. That old seal is not flexible any more. That said, for my time and money I recommend a replacement dishwasher, this one has definitely seen better days. Joe ... Dishwashers

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

The pressure tower came off. I don't know where it came from, nor how to put it back on! It's so tall, it looks like the racks won't close once it's in somewhere. I have no idea how to put it back inside the dishwasher.


With a model # it's hard to give good help but when they ware out the can blow the tower . . you can replace the tower assem ( if ge it will come with lower wash arm other brand it will not .. mm hope this ... Dishwashers

We have a problem with the hobart dishwasher at work, unfortunatley we don't have the manual, its been misplaced, there for i dont have a clue to the make and model, i've searched lots of pictures of the ones i can find on the web, and the one that it loooks like or maybe simular to i the hobartFX400-7ON can you help?


Do you still have a problem with it?Decribe what it looks like and whats wrong. ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Candy CS 455M slimline dishwasher which is 3 years old. The program button has stopped moving round I put dishwasher on and went to work and it was still washing the dishes when I got home from work 8 hours later. I thought it might have stuck and been a one off but no it happens every time is it the timer? is a new timer easy to fit?


... Candy 17 in. CS455 Built-in Dishwasher

Dishwasher problems Hi. I have been having issues with my dishwasher the last month or so. There is a white powder-like residue left on dishes. I noticed it most on my silverware. At first I thought the detergent didn't rinse off completely so I did a ran it again without any detergent a couple of times. Still there. I bought some stuff that is supposed to remove build up from hard water. did that twice. Increased the amount in the rinse aid dispenser. Now I have noticed that the drying coil? is


I've been reading a lot lately about cleaning your dishwasher on a tight budget if indeed you want it working properly as well as clean properly. It is suggested to use ONE Kool-Aid Packet, Lemonade ONLY, and insert that into your wash dispenser to l ... Dishwashers

Dishwasher have a dishwasher that does not clean the dishes properly. It leaves stuff that looks almost like sand on the top of all the dishes on the top rack. I have tried everything I can think of. can someone help me figure this one out


Most dishwashers have a little filter basket in the bottom. Depending on the brand, you can slide out the bottom rack, and in the bottom underneath the sprayer (the propeller thing) there should be some sort of basket that can be removed and cleaned. ... Baumatic 24 in. BFD60SS Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2094 seconds