Having problems with your Hobart LT1-1 Dishwasher ?

As soon as you turn on power it starts to fill

\015 Hobart lt1 Why is it filling before the cycle begins?\015

Answers :

It will look to the wash tank float to determine the water level and temperature. If the machine is empty, it will fill first. before letting a cycle start.
You need to adjust the timer cam
Repair Help & Product Troubleshooting for Hobart LT1-1 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

As soon as you turn on power it starts to fill


It will look to the wash tank float to determine the water level and temperature. If the machine is empty, it will fill first. before letting a cycle start. ... Hobart LT1-1 Dishwasher

Kenmore Elite 13133K started to fill, the door was opened. Now it won't resume, drain or fill, the geen light is flashing. I turned the power supply off for 5 minutes and the problem still exists.


... Dishwashers

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

I borrowed my nieghbors power washer. It worked the first day all day. In the morning i filled the gas with a fuel stabiler, and 30 oil. I may have over filled it. Upon turning it on the oil started leaking from the air filetr compartment. It starts, but then smokes starts to fume and all the oil leaks. Did I break it or is it a easy fix. I cleaned the filter housing. Also the filter was soaked with oil. should i get a new filter and install it or what is the solution. need help.


You will need to get a new filter, and drain some of the oil out of the machine. If you over fill these this will happen. 90% of the time nothing is broken. ... Karcher 2500 PSI Pressure Washer

I have a GE GSD3200 dishwasher about 6 years old, which had been working well until this past week. When turned to 'start' the motor runs but no water fills the tub. I then poured 4-5 pots of hot water into the tub and tried to re-start. As soon as it was turned to 'start', I could hear all of the water draining out. How bad does this sound :) ?


Look inside the dishwasher and there is a little round cup shaped thing in the bottom of the washer. It shuts the unit off if the water gets to high. Lightly push down on it to reset. It should fill with water now. You should look into why it was tri ... Dishwashers

Dishlex global 460 fault.. Always stays on and makes a pumping sound while 'of' is displayed. Only way to turn it off is at the power point. Have tried turning it off at the power point for some time and re setting by pushing start & program at same time with no luck. According to the manual the code says "incorrect fill levet or time " and contact service for help. Any ideas?


... Dishwashers

I have a McCulloch FHH18A power washer. When plug it in without the water turned on, the pump will start. As soon as I turn the water on to the unit, the GFCI power cord trips. Water does flow through the unit as I have water at the wand nozzle when not plugged in. Any suggestions?


I would guess there is a leak somewhere inside the unit that is spraying water on some electrical component and causing a ground fault. ... McCulloch FHH18A Electric Pressure Washer

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

It does not matter which cycle is chosen, once "start" is pushed on our Asko D3120W the drain pump comes on empties the machine, then it fills for the first time, and turns off. It happens on all cycles. We have turned off the power thinking that would re-set the machine, but it has not worked. Do we need service or is there something we can do at home?


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012seems to be with the frozen main pump or the pump seal/impeller gone bad. To\015\012solve this the pump and motor has to be removed and then the part rep ... Asko 24 in. D3120 Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

As soon as I turn the dishwasher on, it starts to fill up with water but the motor does not come on. Any solutions?


... GE 25 in. GSC3200Z Free-standing Dishwasher

Miele G 841 u plus. the safety pan continues to fill with water and activates the intake/drain mode and the pump continues to run as soon as power is turned on


... Miele 23 in. Novotronic G841 Built-In Dishwasher

Pump starts as soon as main switch is turned on, even with door open. Also does not even try to fill. Does count down if you close the door and let it run but no water so no effect. I am guessing control board or anti-flood? Thanks


Is your door switch defective,that will cause same symptoms ... Bosch 24 in. SGV57T03GB Built-In Dishwasher

I have a model SHE 44 C05 UC/40. It is three years old. It starts up fine, fills with water and goes into the wash cycle. Then it continues to wash indefinitely, even though the electronic timer display counts down to 1 and sets there. It still continues washing until you turn it off with the power button


... Bosch Dishwashers

As soon as the motor starts up after the dishwasher fills, the motor makes a loud grinding noise that turns into high pitch whining. Water begins leaking from above the pump.


That shows a leaking water seal. Water would run into the motor bearings which then rust and make noise. You probably need the motor / pump kit. ... Dishwashers

Hi there, my F&P nautilius dishwasher starts the cycle as soon as I push the power button but only pumps out then swithces off. It won't let me set or change the cycle. I turned it off and left it over night and in the morning it had overflowed with water. There is no fault code showing on the display either.


When you said overflowed with water did the water come out the door the float switch in the unit may be stuck either opened or closed which if it were stuck or the switch itself were broken then the unit would have water go in and immediatley go out ... Fisher and Paykel Dishwashers

Westinghouse SB920 dishwasher starts pumping water out as soon as power turned on at wall socket


... Dishwashers

Not filling dishwasher prog will turn on but does not take in water and bleeps soon after starting


If the machine is not filling, then it is probably a faulty inlet valve. Check the float switch and the power supply lines at the back first.See here how to ... Belling 24 in. IDW603 Built-in Dishwasher

My dishwasher motor starts running as soon as I turn power on, with the door open - but nothing happens - no water enters nothing


... Magic Chef Built-In Dishwasher

CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??


You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers

Kenmore Elite 665.17053400. Powers up ok, fills up with water ok, but wash cycle won't start. I can hear the motor trying to turn but sounds like its seized up. If I cancel the wash, the machine drains out the water ok. Does this sound like the moter is shot and if so, what should I expect to pay to have it replaced?


This dishwasher has a very sophisticated wash system. In order to improve the wash efficiency it uses a chopper and a soil sensor. It is very likely the chopper assembly is clogged which is blocking the water from circulation and straining the wash m ... Kenmore Dishwashers

We have ASKO 1805 dish washer. As soon as turn on the power all lights are start flashing and there is no response whatever button is pushed. All the lights simply keep flashing. There is no water being pumped into the machine.


Child lock may be activated ... Asko Dishwashers

I had an IE code displayed on LD1415M LG dishwasher and replaced inlet hose (with builk in aqua stop valve). Afetr reassembly, dishwasher now tries to fill as soon as power switch on door is turned on, before program is selected.


Test the timer: can be bad adjust it. see the diagram for you check again any wires in wrong place, any devices with bad adjustment. ... Dishwashers

I have full power to the washer, but as soon as i hit start to begin the cycle, i lose all power. i then have to unplug it and then plug it in again and then i get power back agin. as soon as i hit start again i lose all power to washer again. im thinking maybe the mother board is shot????


... EuroTech 24 in. EDW154E Built-in Dishwasher

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1269 seconds