Having problems with your Hobart LT1-1 Dishwasher ?

I changed the fill valve assembly and coil and now dishwasher drains all water out and doesn't have enough to start running without pressing the fill valve.


Answers :

Repair Help & Product Troubleshooting for Hobart LT1-1 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I changed the fill valve assembly and coil and now dishwasher drains all water out and doesn't have enough to start running without pressing the fill valve.


... Hobart LT1-1 Dishwasher

I changed dishwasher fill valve and coil and now dishwasher is draining all the water out and doesnt have enough water to start wash.


Make sure the drain line goes at least to the top of the unit before it goes down ... Hobart Dishwashers

Frigidaire dishwasher M#fbd1050rem2 - When started water fills for a short while, then makes a constant 'whirring' sound without any wash. This sound seems to be the motor running but no pumping. When cancel button is pressed , unit drains well and complete. Am I correct to assume this is the wash impeller?


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

FDB520RHS2 Dishwasher Same problem as posted. Dishwasher has power & water - control panel lights are on, when start is pressed the sound of a relay can be heard but nothing else happens - no water fill no cycle. Unit stays in this condition without running.


... Frigidaire FDB520RHS Full Console Dishwasher with 4 Wash Cycles 4 Wash Lev

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

I have a Bosch SGS43A22 Dishwasher approx 8 years old. When I start a cycle it fills, runs for about 15 minutes, then drops out about a litre of water from the bottom of the door, then completes the cycle without any more leaking. I have run the machine with the front panel off and can see that water bypasses the top of the seal and fills the well of the seal then pours out. It only happens the once. The seal is fitted correctly. Any solutions?


After 8 years service the seal may have perished, so you should feel for a crack by stretching the rubber where you noticed the leak. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Hello, my Bosch Classixx dishwasher SGS43E42EU/21 has me stumped. It starts by taking in water but when "filled" pumps out for a couple of seconds then refills for say 10 seconds more before another 2 or 3 seconds of pumping out. This cycle continues for ages without starting to wash. I've tried various things: - checked the Auto Stop valve isn't being activated by leakage (removing the polystyrene float and bottom tray makes no difference - there's no leak) - the valve seems to operate it


Hello Dave,\015\012\015\012Sounds like an overfill problem - the symptoms are consistent with a failed pressure switch. Water enters the dishwasher through a chamber which has a float arm connected to a small microswitch -this is the pres ... Bosch Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

I press start the water fills fine as soon as it start running i get a loud humming/ vibration and nothing happens?


Sounds like the motor is bad.after it fills the motor should start,has it been leaking under the bottom of d.w.rmove the bottom front panel and see if there's any water stains,usually the motor will leak before it finally dies. ... Frigidaire Dishwashers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

My KitchenAid KUDI01FL dishwasher will not start. When I run the self test all of the LED lights come on and stay on indefinitey without blinking until I press cancel. Then the cancel light comes on without blinking. What does this mean? Thanks!


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Pressure washer only starts and runs on full choke. throttle open. The pressure washer turns off when we press the trigger to start washing. Is this because the throttle isnt set high enough?


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher not getting enough water in either drawer, although top drawer gets more. Dishwasher keeps beeping during cycle and reads not enough water and then stops running until you press the start button. Need Help, any ideas?


This sounds like a hard water deposit problem.Check your water inlet valve for a screen and see if its clogged. Also it may just be a water valve/solenoid problem. As in, it's too crusted up to float up and down.Some models have a water f ... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Bosch SHX46L15UC keeps draining, won't fill. I believe there is a stuck float valve. Need help to repair float valve. Pressing power button causes drain to run constant.


... Bosch SHX68M09UC 24 in Builtin Dishwasher

Model # SHU 8806UC/14 When start button is pressed, with door open, it begins to cycle and even if we close the door it just runs and runs but never dispenses soap from the dispenser or even fills with water. Any thoughts?


... Bosch Dishwashers

I started my dishwasher this morning. It started to fill with water, then stopped. I can hear a very slight hum sound as if the motor is running. The start/reset light flashes but does not reset upon pressing the button. Any ideas for a self-help resolution?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... GE Nautilus 24" Built-in Dishwasher

Unit Runs fine, except when you press the spay gun the engine stalls out. Unit was working fine, ran out of gas, filled tank and started engine. Engine was running fine, triggered spray gun and the engine stalls out.


... Pressure Washers

When I press the black (start) button, the machine does not start filling with water. However it has more than enough water on the rinse and other cycles.


... Jet Tech Systems 20 in. F16DP Built-in Dishwasher

When we start the washer, it comes on and starts to run (we can hear it) but does not get past the initial startup to fill with water. Is it the pump? Inlet valve? thanks.


... Bosch SHU9925UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1708 seconds