Having problems with your Hobart SR24C-4 Dishwasher ?

I am working on a hobart wearwasher and I have no power

\015 I am working on a hobart wearwasher and I have no power to the fill valves mod#sr24c \015\012\015\012 howards equip repair \015\012\015\012 thank you\015

Answers :

Repair Help & Product Troubleshooting for Hobart SR24C-4 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hobart LX30 Hey I just bought a Hobart Lx30 and we don't have a power source that can handle the 50 amp requirement. We got it at an extremely good price so we are trying to work around it. I was told that disconnecting the water heater would allow it to work in a standard 120 volt outlet. I did that and now I have another issue. The machine wont run unless the water is 160 degrees. How do i disconnect the sensor that restricts the temp so that I can run the machine at a lower temp?


Hopefully you took the suggestion to run the correct 50 amp 208-240 service to the unit.Converting the unit to an LX30C has a couple of pitfalls. The LX30C is connected directly to the incoming water supply, which should run 120-140 degre ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I am working on a hobart wearwasher and I have no power


... Hobart SR24C-4 Dishwasher

Hobart LX30H leaking at door. Power drain works.


Leaking at the bottom edge of the door can be caused by the lower spray arm having a split or crack which allows water to spray directly at the lower door instead of up. A close inspection of the lower arm or watch it work with the door open. You'll ... Hobart Dishwashers

No power working on a hobart modal sr24cdishwasher I have no power to the incomeing water solenids


Hi,\015\012\015\012Have you actually tested with a voltage meter to see if there is power to the connections on the solenoids?\015\012\015\012Firstly check the inlet tap, there maybe a filter that is blocked. make sure water f ... Hobart Dishwashers

Hobart AM14/1 free standing dishwasher with booster. Booster will not heat up beyond 41C. All three heating elements check ok with Ohm meter. High limit not tripped. Temperature screw up at maximum, when you turn the screw, you can hear thermostat click at lower temperature on and off. When turning on main power for dishwasher, heater in dishwasher works fine, but no relays click in the booster tank area. Have not checked for power at booster, have checked all fuses with meter and are ok. Ple


... Hobart AM14-253 Free-standing Dishwasher

Power light is blinking and dishwasher is not working its hobart GL71H


Dont no a way to by pass it but looks like master board gone faulty , just needs to be replaced ... Dishwashers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

Dishwasher would not work and clean light would blink seven times. Asked an expert and they said to hit saniwash and heated dry two times. This work for a couple of times but now the dishwasher acts like there is no electrical power goimg to it. I tested the power with a voltmeter and there is power going to the circuit board.


Normally this happens when the dishwasher electronic control does not detect a water temperature increase during the main wash cycle. The issue could be in the heater element, the thermostat or the wiring that is connected to those or on the electro ... Dishwashers

I have a 6th sense dishwasher purchased new October 2004. It has been working properly and then has just stopped the next time I tried to use it - it will not turn on no matter what buttons I push - no response. I have checked the power out let with another appliance and that works so it is not the power supply from the power point. I can only think it must be a fuse or the controller. Can you please advise best course of action? Thanks Helen


I rang the appliance man to fix the problem.\015\012\015\012Thanks anyway Helen ... Westinghouse Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Opened door and unit did not have electrical power (lights did not come on either unit). Called serviceman. He stated there was no electricity to unit(s). Called electrican. He stated wiring to the dishwasher had power. Called serviceman again. He came out and dishwasher worked. He did nothing to it. I opened the door and the lights(buttons) came on. Unit worked for a few days and this morning, there was again, no power to the unit. What is likely wrong with this dishwasher?


... Fisher DD603B / DD603W / DD603H Dishwasher

Neff dishwasher has power but no light on. Won't work. Loud bang heard during cycle then stopped. Had panels off and pump works when float switch is lifted. Could this be capacitor at lower back where power lead comes in ?


... Neff 24 in. S5443X2 Built-in Dishwasher

Hi there . Beko DWD4310 stopped working , no "power on" lights, changed control panel as advised here, still not working, checked on off button with fase tester power getting as far as there. Any suggestions ?


I can see a couple of possibilities as to why the on/off light is not turning on.\015\012\015\012Either the door switch is faulty or the thermal fuse is blown.\015\012I do not have access to a service manual - so cannot provide the ... Beko Dishwashers

I have a GE Quiet Power 2 and the face plate (buttons) stopped working (i.e no lights, sound, action). Is there a fuse for this or something I can dismantle and replace? The dishwasher shares power and the shared sources are still working and the breaker is not tripped. Any suggestions?


Look for a bad fuse on the control board. Soldered in near the power connection. You may see a burn mark from under the fuse. ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

No Power My Whirlpool Dishwasher DU900PWKQO was working yesterday and now does not have power to it. Is there a reset button to press or can a dishwasher just stop working?


You probably have a bad door switch assm, there is no reset on this unit, if you have a bad door switch the unit thinks the door is open so it won't start. ... Whirlpool 24 in. DU900PCD Built-in Dishwasher

Our craftsmen electric pressure washer stopped working while in use. We have power - red light on gfci and we tested the master switch - has power too. So what can be the problem? One post mentioned a jammed pump switch. What is that and where is it? We used it 2 weeks ago and it worked fine.


The pump switch they spoke of is an internal switch. It is activated by a valve so that when you let go of the trigger, the machine shuts off. This valve is stuck or the switch is bad. Usually the valve is the problem. I would go to Sears and get ... Pressure Washers

No power dishwasher worked great then all the sudden get no power to the top drawer .botom works fine .


Top drawer turns on runs aprox 3 min then starts to beep and we have to turn it offthe clock pops up and and stays at 2;00 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My whirlpool gold dishwasher has stopped working. i checked the power and it does work, but the dishwasher acts like it has no power.


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My LG 24 in LDS 5811 ww quite working in the middle of a cycle. I have power to the machine, but no lights come on, nothing works. I turned off the power and removed the front pannel. The large brown wire and large orange wire that are plugged into the back of the control panel start to smoke. So does the large black wire and the large white wire. Any ideas, is this the heater or is the panel bad?


The unit will need a new Wire harness, Pump/motor assy, Main Pcb and inner door liner.\015\012Contact LG @ 1800 243-0000 they may help you out. ... LG 24 in. LDS 5811 Built-in Dishwasher

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1016 seconds