Having problems with your Hobart SR24C-4 Dishwasher ?

I have a single tank conveyer type machine. The final rinse temp is 195 degrees F but the utensils, trays, pans silver ware all leave the machine very wet and take numberous minutes to dry. I believe the curtains are to long at the entrance not allowing for air circulation. I am a Environmental Public Health Specialist for a county health department. The machine is at a school I inspect.


Answers :

Repair Help & Product Troubleshooting for Hobart SR24C-4 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a single tank conveyer type machine. The final rinse temp is 195 degrees F but the utensils, trays, pans silver ware all leave the machine very wet and take numberous minutes to dry. I believe the curtains are to long at the entrance not allowing for air circulation. I am a Environmental Public Health Specialist for a county health department. The machine is at a school I inspect.


... Hobart SR24C-4 Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

Bosch dishwasher runs too long, over 130 minutes on regular cycle, then when it gets to the final minute, it continues to run for a long time. The sanitized light doesn't come on, and dishes are not hot and not dry.


Http://www.acmehowto.com/howto/appliance/dishwasher/dishwasher.php\015\012\015\012Please find above, a troubleshooting how to ... Dishwashers

Matsui mf145 dishwasher appears not to finish its washing/drying cycle. first couple of washes machine bleeped 8 times and dishes were clean and dry. now after around 2 hours machine bleeps for around 1 minute and when opened a lot of suds are left in the bottom of machine and dishes are still wet.


... Dishwashers

The GE Profile Dishwasher will not allow me to start without the heated drying light coming on. I want to wash without this headed drying at the end of the wash. When I try to turn it off it turns the start cycle off. This happend over and over again when I want to turn on the machine, It finally lets me get an unheated dry wash started to complete. A problem every night. PDW7800N15CC. Serial MM8243388


... GE 24 in. Profile PDW9800J Built-in Dishwasher

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

I have whirlpool diahwasher ,model DU1055XTSQ3,quiet partner -1. when i start the machine the folowings things happen: 1.the machine does not start . 2.Start /resume light starts blinking ,after few seconds ( 40-50 seconds), the pots and pans light also starts blinkng .after some time ( 1 minute ) the normal light also starts blinking .All three lights start blinking 3. I have done the following to rectify the problem from the book : alnernatively pressed heated dry and normal keys for


... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

I have a very old domestic Hobart dishwasher. The micro switch that is controlled by the float on the inside left of the machine has malfunctioned . I believe that this micro switch controls the "water in" valve/solenoid. It's ID = UNIMAX 2TMT2002 4 Y , 10 amp-1/4hp 125-250VAC. It's an odd switch as it's lever is about 25mm long and has a paddle on the end to line up with the plunger comming through from the float inside the machine. It also only has 2 prongs for connection and 2 holes fo


... Hobart Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

Dishwashing SMEG SDCY 66 (made in Italy) As soon as machine is starts (from program 4) water supply valve open and water running in about let say 5 minutes no any further functioning and some strange nice from below looks like something is running dry. What can be the case?


... Smeg Dishwashers

After starting dishwasher to do a normal wash with heated dry, the dishwasher stops and Clean light blinks 7 times, pauses and this continues until I reset the machine. After reset it goes to rinse only and goes for a minute or so and stops.


Hi\015\012\015\012Please check if the clean light is blinking 7 times. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To reso ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

The model number for my dishwasher is DGBD2432KW. It is showing the letters HD in the window that normally counts down the minutes. What does HD mean? The machine seems to be running too long. Th


... Frigidaire Dishwashers

My control panel panel has the normal wash and heat dry buttons are lit and nothing else happens. it will not allow me to turn the machine on. the start reset button does not operate the dw


Sounds like it is either a door switch problem or an electronic control problem. Best off to call a reliable service company such as Sears. ... GE Dishwashers

I try holding the cancel/reset buttons to lengthen the time to allow for better drying. I have followed the directions given in the manuel. It doesn't seem to be working. Could you outline the steps for me... 1.) Hold both buttons down simultaneously... 2.) turn on machine... then what?


... Bosch SHU5307UC Built-in Dishwasher

Something was stuck in the latch, which made the machine not start. I removed item, however, the lights come on, the heat comes on, bot no water or the rest of the cycle begins...help.. I have held down start/cancel and the heat dry buttons. I have unplugged the power for three minutes... I have taken the front covers off, looked through the latch mechanism but found no other issues. There is a little water left in the basin, so I checked to see if there was a clog, by blowing air into th


Hi,Sorry for the delayed response. Your problem dated 30th Sep 2009 was reposted today on FixYa. I am sure by now some other expert must have responded to your question and solved your problem.If this is not the ca ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Maytag mdb9150 dishwasher stopped at some point last night--found it this morning with flashing lights--I think "clean" and "heated dry", not sure.  I used "drain/off" to make sure there was mechanical noise--there was, so I don't think the machine is dead.  Purchased on 2001 with 5 year warranty, so out of luck there.  I tried turning off the electricity to the unit for a few hours; nothing improved.  When you start it (or think you have!) it makes noises for about a minute that sound promising


Check pump and solonoids click/work, if no mechanical noise, could be the circuit board, but they can be expensive. :(\015\012if the solenoids click, and allows water in, then the pump might be jammed, with grit, clean and reinstall... good luc ... Maytag 24 in. MDB9150A Built-in Dishwasher

Hi - I have a Neff S5456X2GB/13 and it has decided to wash cold and doesn't dry. When washing in auto mode it seems to take forever but does eventually stop, and I've noticed that when opened the time to go indicator can vary quite a lot (sometime goes backwards in that if you wait ten minutes and look again, it's saying it's going to take longer than it did before) I have replaced the pump in the past so I know how to dismantle the machine. What are the possible causes of this problem and ho


Ok, really you have maybe three problems, that to me seem interconnected.\015\012\015\012First, IF connected up to the Hot water source, then either that has failed or the Inlet Solenoid has.\015\012\015\012Second, the heating element has ... Neff Dishwashers

I have a Miele G1140 SCI Dishwasher. When I start it after a couple of minutes the Wash,Drying End Light starts flashing and the machine stops . Please could you advise me if there is anything I can do before calling someone to come and have a look at it.


... Dishwashers

Model SHE68P02UC/60 There does not appear to be a drying heating element in this dishwasher or did we miss connecting something up during the installation? Unsatisfactory drying on both "normal" cycle and "auto wash" cycle.Drying agent is in machine. What is "condensation drying"? Is this just blowing cool air through the machine and out through the vent? If so it is unsat. How to get the machine to actually DRY the dishes? I'm going to be very disappointed and out over $1,000.00


I am assuming you have the dishwasher connected to the hot water tap which can give water at about 40deg c (120deg F).\015\012\015\012The dishwasher uses steam from the water (after heating it further). So if the inlet water temperature i ... Bosch Dishwashers

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1139 seconds