Having problems with your Hobart SR24C-4 Dishwasher ?

Due time maintenance falt - Hobart SR24C-4 Dishwasher


Answers :

Repair Help & Product Troubleshooting for Hobart SR24C-4 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Due time maintenance falt - Hobart SR24C-4 Dishwasher


... Hobart SR24C-4 Dishwasher

Hobart lx18h Our commercial Hobart dishwaser stops working after running a few cycles. After pressing start the LED display will continually blink and nothing will happen. We'll turn it off and on again a few times to reset it and it will start up again eventually. We've had an appliance guy look at it multiple times. He's replaced a part or two for it but the problem continues and he isn't much help. Anyone else had any similar issues with this model of dishwasher?


... Dishwashers

Hobart sr24c door leaks - Hobart SR24C-4 Dishwasher


... Hobart SR24C-4 Dishwasher

Why would a dishwasher filter split/break in a meile dishwasher that is not even 3 years old. i have been told that it is not under warranty and that i have to pay the $580 bill even though i feel that it must have been the dishwasher as the maintenance man said that it would have been nothing that i have done. i have had other less expensive dishwashers that lasted a long time. i am going to write to meile and see what they say. what do you think? should i persue this as i feel it was a


At v3 years old, you have no case. you may have dropped something heavy on it ... Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

Maytag dishwasher #33323190JG Many of the dishes come out with a white-ish coating. I usually end up using an SOS pad to scrub it off. Three weeks ago a repair man replaced the heating element due to the recall but that didn't help it. He suggested trying "Dishwasher Magic." I've used Dishwasher Magic a couple of times within the last two weeks but the problem remains


Hi,\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... \012Bought new spray arms online and installed them in minut ... Maytag Dishwashers

I have a 12 year old Kenmore Ultrwash Model #665.15951790. I recently replenished the rinse aid dispenser and am experiencing an oversuding problem. It was oversuding to the point that suds were coming out the bottom of the door. Did notice that the blue rinse aid seemed to have leaked into the dishwasher due to a puddle of blue rinse aid at the bottom of the dishwasher. Have run a "quick rinse" cycle 4 times with no dishwasher soap added and still have sudsing. Can the rinse aid cause oversudin


... Kenmore 15129 Built-in Dishwasher

Ignis ADL347 integrated dishwasher runs for a few seconds then stops, beeps and light flashes 6 times. I'm told this is due to water not getting into the dishwasher. it was working perfectly until we had a washing machine installed, can't see any pipes that are twisted or crushed but also don't have great access to the back of the washing machine or dishwasher. I have no expertise whatsoever. What should I be checking/trying? Any advice appreciated.


... Dishwashers

Hobart SR24C-4 Dishwasher can't drain completely


If this is a new occurance, and not "since it was installed", it may be the drain impellor. Little fins on top of the impellor sometimes get worn off. It is under the lower wash arm in the pump housing. The only trick to taking the pump apart is not ... Hobart SR24C-4 Dishwasher

Hobart am14 How to adjust wash time cycle - Hobart AM14-253 Free-standing Dishwasher


... Hobart AM14-253 Free-standing Dishwasher

Our Frigidaire Dishwasher buttons stopped working. If we push normal cycle it will not select as well as other cycles. The last time it happened the maintenance guy came and turned it on and off and it started working again. That didn't work this time. We still can't select some of the wash buttons


You will have to replace that selector switchhttp://tclaundryrepair.com/ ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

*Beeping* thing Hobart SR-24 Dishwasher Beeps at me. Has beeped on startup since service tech was here last month...thought he fixed something we didnt even know was broken.....but now the thing beeps mulitple times a day...sometimes mulitple times in one cycle. What does it want?


... Hobart SR24-H Built-in Dishwasher

Hobart SR24H dishwasher after rinse cycle the same time pampas water in and out of the dishwasher, two pipes are opened and working


Hello.\015\012As per my personal opinion this is normal because for the final rinse you have a small booster or boiler..\015\012When you turn on the machine..it starts fill and also the booster for the final rinse.\015\012You start the ma ... Dishwashers

Where do I get a lower door gasket for a Hobart SR24C dishwasher?


A common fault with Hobart dishwashers leaking from the door, is the cleaning plugs dropping out from underneath the wash arms. It causes wash pump water to spray on to the bootom of the tank, and when the arms rotate to a point near the door, it ten ... Hobart SR24C-4 Dishwasher

I purchased a new dishwasher on 2/22/07 at the Home Depot in Parksburg,Pa. I first had to have it repaired on 4/28/08 for wires stuck to inner door. They repaired two broken wires and added insulation so wires do not stick to the door. The second repair was a little more than two months later. On 7/18/08 they had to install a new motor because the motor locked up. Both times I waited several weeks due to not having money and appliance center being busy. I used J.B Zimmerman in Blue Ball,P


Hel1Dav2,\015\012\015\012I understand your frustration with having to deal with major repairs to a new applaince. However, I don't belive this is the correct forum that you need to use. I have found a helpful link that you may try in th ... Dishwashers

Hobart dishwasher ml130017 booster stays on all the time even after it is turner off


... Hobart 25 in. LXIH-4 Built-in Dishwasher

Kleenmaid DW10 dishwasher has blown motor. Everything else works fine. Service guy said part has to come from Brandt in France. About 6-8 weeks but no guarantee if it will arrive at all due to Kleenmaid's problems. Any other time and cost effective way of replacing the motor?


Time and cost effective way = have the electric motor repaired. All an electrician needs to do is to rewind the coils inside the motor and replace the brush... you will save around 80% if you will just have it repaired plus, it would only take 1 week ... Dishwashers

My sa8200x smeg dishwasher the programe start ,pause button will not work .on investigation i found that the button pushes on to a plastic lever wich over time has worn and cracked due to fatiuge the number on this plastic part is 48800142 it also has a circle with a line through it followed by 3inox iam having trouble locating this part does any one how to get this


... Dishwashers

Hi Hobart Model H50SU-DW. We cant seem to be able to pump out the water. I think we need a maintenance check and would like to know who will come and service this dishwasher in our area. Tarneit, Victoria


... Hobart Dishwashers

I have a dishlex DX301 dishwasher and the soap dispencer never fully emptys out. (it may do 1 in ten times) i have tried drying out the box so that it will not clog but this does not seem to work. When i look closely at it i cannot see how the flap open to empty. Is it due to a poor design fault??


... Dishwashers

Hobart LXIC under counter comerical dishwasher. Delime lled keeps comeing on every time power up. Checked sensors on bottom in the water drain area senser on right (there are 2 next to each other on this unit I think other is water temp) the wire had wire burn completely off. I reconnected the wire and started to burn up the wire again. Question: 1) Is this sensor for the Delime sensor? 2) does it sond like the sensor is shorted to you? or sending wrong voltage to sensor? 3) If no


... Hobart 24 in. LXIC-5 Built-in Dishwasher

We have a Frigidaire dishwasher model #FDB634RF bought new. It was used for a not very long period of time but developed problems due to well water with high lime content. now with good cleaning products available it is ready for use again. The problem is the top spray arm that refuses to rotate. I have taken the arm out and thoroughly cleaned it of deposits checked the supply line from the pump and checked the sump for any obstruction. The arm turns freely by hand but water just pours out the


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Frigidaire 24 in. FDB635RF Built-in Dishwasher

My KitchenAid Superba by Hobart (KDS-58) portable dishwasher has begun leaking and runs at about three times its previous volume. I don't know how old it is but I would love to be able to save it if there are any repairs I could try myself. Any suggestions?


... KitchenAid Dishwashers

My asko dishwasher(1504) keeps running sometimes, The time will run down to 1 min on the disply and stay there and run on and on until I turn it off. Prior to this another problem occured, when the washer does shut off on it's own, the display will read F1(Falt in the heater), I am wondering if one problem has to do with another. The heater problem I can deal with but not the continueous running.


F1 doesn't mean that it's always the heating element itself, often it \015\012can be the control board relay that has shorted and isn't sending power \015\012to the element. If the element is the faulty part, you'd be looking at \015\012about $250 f ... Dishwashers

I have a Frigidaire FDB2410LDC3 Dishwasher. It was working great until my 5 year old fell on the door and it does not spring back up now. I tried looking with a flashlight in the sides and the springs may be OK. What is most mystifying about this is something has gone wrong with the part your hand uses to close and open it. The latch is limp so I wonder if there was some other spring in there that broke in the incident. Now after some time of forcing it to shut (due to that pesky latch that


Prhandle and latch.obably sprung the hinges. The reason it dont want to work right is the door latch is not latching properly and therefore it wont start. I would start by replacing the hinges and springs and the ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1697 seconds