Having problems with your Honda 2500 PSI Gas Pressure Washer ?

Honda pressure washer won't pull chemical. Line is not kinked. Removed intake fitting anf checked for clogs - not clogged. Appears to be drawing but not enough to pull the clorox bleach from the bottle. Using the soap fitting so that's not the issue either.


Answers :

Repair Help & Product Troubleshooting for Honda 2500 PSI Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Honda pressure washer won't pull chemical. Line is not kinked. Removed intake fitting anf checked for clogs - not clogged. Appears to be drawing but not enough to pull the clorox bleach from the bottle. Using the soap fitting so that's not the issue either.


... Honda 2500 PSI Gas Pressure Washer

The top spray arm of my Frigidare model FBD4315LFC0 Aqua Surge dishwasher fell off. Their appears to be a missing part. I've been searching online for a schematic and can't find one thorough enough to use. The parts I have are: 1. The top sprayer arm (the one in the top of the tub) 2. The two piece plastic keeper ring that appears to fit into the top of the spray arm. 3. A small white grommet looking item that fit inside the keeper nut. 4. The keeper nut that screws directly onto the wate


Hello there:hey sorry i keep getting disconnected i will be back on really soon i need to find out what is going on i hope these things that i have discussed with you is helping you out the parts are not as hard as they look once yo ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

Whirlpool GU1100XLTQ1 dishwasher, 4 years old is leaking water during cycle. I cannot see exactly what is leaking by looking up through the acess panel in front...there are what appear to be plastic support ribs for the tub and water is leaking through several of them to the left of what appears to be the motor in the center...please help! I don't think I can run the washer and tilt it back at the same time as the water supply line only allows me to pull it out just enough to clear the counter t


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wahgfadh ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Soap (Simply Green) is not being pulled from ciphen hose? I unscrewed the brass male fitting, where the clear cyphin hose is attached, and observed a small spring and ball bearing? Nothing appears wrong, what can or should I do to ensure outgoing stream of water contains the cleaning agent?


... Briggs Pressure Washers

Mbd7600awq How do I replace the front door panel? I have pulled the unit out enough & removed door springs. It appears that door can be removed (flats on pivots may allow it) but door bracket hits bracket on the unit. Help! What is the secret?


... Maytag Dishwashers

ASEA Cylinda 1200 Appears to let enough water flow in to the unit at the start of the cycle, but the pump does not start when the water level appears OK. Appears to pump out at the end. Has it died of old age or is there something I can try?


... Asko Dishwashers

Our 8 year old integrated 2 draw dishwasher (top draw) has a problem on the rinse cycle and constantly beeps and water at the bottom of the draw remains. I have cleaned out all the grit and stuff residual water and tried to use again. But alas there appears to be a blockage still on the rinse cycle. Can you help or do I need to get a plumber? Thanks...Louise


Sorry i lost you my breaker tripped ... Dishwashers

Is there anyone out there that can HELP!!!!.I have the f/p dd603h model and have had nothing but problems with it the latest being the bottom draw is a struggle to pullout+top draw keeps beeping very very annoying!!!!.Have tried to locate actuators by pulling out bottom draw but not quite sure what I'm looking at,and are they easy to replace?


The source of the problem could be the power filter board at the base of the dishwasher under the bottom drawer. This supplies power to both the drawers as well as operates the actuator motors for the drawer lid seal. You could replace the power ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My dishwasher is a Smeg model STA 6143, and the door won't close. It seems fine until the last few centimeters, then it jams and won't close easily. If you press hard, it'll shut but not latch. Nothing appears to be stuck anywhere. We've tried jiggling the door but it seems somehow to be misaligned, although there's no reason why it should all of a sudden appear to be so. The electronics work fine, the racks fit fine (we also removed them, and the door still won't close), and nothing appear


... Dishwashers

My 13 year old Frigidair dishwasher (model FDB221RFR2) is not disolving the soap tab that drops in during the later cycles. We sometimes find the soap sitting on dishes or on the bottom. It appears that there may not be enough water but I'm sure of how much there actually should be. It also appears that the soap may be dropping late but again I'm not sure of when it should normally drop. I checked the inlet value and it appears to be ok. I also checked the timer (to the best of my ability) and i


CHECK YOUR WATER TEMP, IF ITS NOT HOT ENOUGH SOAP WILL NOT DISOLVE. I HAVE ALSO SEEN INTAKE VALVES DROP OUT LATER IN CYCLE. THAT MAY BE YOUR PROBLEM. GOOD LUCK! ... Dishwashers

We have a Kenwood KDW8ST2A Dishwasher which is about a month old. The other day we had to pull it out from under the worktop because something rolled under it. When we put it back and went to use it later that day, we got an E1 error code appear and it's been like that since. We pulled it back out to make sure that we hadn't accidently pulled or loosened any of the pipes. We have the manual which does tell us what the error means but it doesn't tell us how to fix it. I'm sure it must be somethin


You can find a manual here ... Dishwashers

Kenmore dishwasher Have a kenmore 655.15889020 dishwasher which does not appear to be pumping water fast enough. No apparent blockages. Arms circulate very slow. Enough water in sump. Could it be the motor for some reason is running slow? Or maybe some valve is not closing properly.


Fatubu, are you sure you have the correct model number, Im not finding anything on the posted model. They had an issue on models close to this that had an issue with a twisted or missing seal in the pump assy. causing water to fill the pressure swit ... Kenmore 24 in. 16032 Built-in Dishwasher

Power is on, lock symbol appears in display panel of both upper & lower draws. On pressing lock button on either draw you hear a click however their is nothing else showing in the display panels & there is no response when pressing the power buttons or any of the other buttons. Every thing is completely dead. Is their a fuse or overload button?


Hi \015\012If the key/ lock symbol is showing in the display, then it is possible you have the child lock on. Disable it by pressing the key/ lock button on the panel. Press and hold the "Lock" icon again until o ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The pump doesn't seem to put out enough water pressure to turn the various revolving heads/nozzles in the washer - all washing heads are operable (ie unblocked) while the S shaped nozzle at the base and the small round nozzle at the top/ceiling of the cabinet do revolve slightly or slowly - but the two main nozzles spout water but not enough to revolve Is this a defective pump or a partially blocked pump ? - or something else - I have checked everything else and they appear to be functioning


It will be helpful to know the make and model number of the dishwasher to diagnose the problem you have.\015\012\015\012Generally this is attributed to a blocked chopper assembly in the wash circuit but hard to be sure if your model has o ... Dishwashers

My DD603 has been working perfectly well until recently when the top draw stopped working as though the power had been removed. I have checked akk connections which appear OK, but I understand there is a problem with the top draw in that the thermistor goes. I would welcome your experienced help and advice as I understand one cannot just replace the thermistor.


Hi just read your posting.Now there are a couple of reasons that the draw does not power up.The first is the element to heat the water is open circuit,The second the control board is faulty or your wiring is faulty.The last is your lid activator boar ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

My dishwasher is leaking from underneath, front left as you look at it. If i go underneath it, there appears to be a seal on the outside (it does not appear to be the one that runs along the bottom of the inside of the dishwasher) that has come away at one point. Do you know a) how to get the front panel off (the bit that makes it look built in),b) how can i get another one of these seals. I assume if i get one we can just fit it into place. Many thanks, Robyn J


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012p80897 ... Neff 24 in. S5453X1 Built-in Dishwasher

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers

It will not take the chemical/soap in the pressure washer? I have checked both ends on the chemical hose and both seemed to fit tight on recievers. Then I checked and did not see where it was pulling air in the hose to keep it from pulling from chemical bottle. This is a brand new washer. Am I doing something wrong?


... Pressure Washers

Maytag dishwasher MDBTT50AWS Door Latch broken. Screws hold the top. The bottom appears to fit into ''plastic teeth'' . Are the teeth supposed to have top and bottom or just bottom teeth. It appears mine has broken teeth on bottom. Is so, do I need to replace control panel to hold latch at bottom.


... Dishwashers

It appears that there is not enough water pressure through the sprayers to to wash food 'deposits' off the plates and dishes.We have well water and it has a some what high lime content so I suspact that there is some calcium / lime clogging in the machine. I thought of removing the pressure pump to see if that is clogged up but before doing this, have you any other sugestions(i.e run vinegar through the pump? ). The holes in the sprayer . rotating arms appear to be clean.The machine has been e


The water-inlet valve lets water enter the machine. Make sure it’s not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. There is a video of this at ... Kenmore 24 in. 16032 Built-in Dishwasher

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Working on a Whirlpool dishwasher DU915PWSS0 - The soap dispenser won't open automatically. We have replace the wax motor and have installed a new control board. When you pull up on the draw bar manually the dispenser door opens perfectly. I don't have a schematic and I don't have the test sequence so I can't run the diagnostic test. It's a blind assy process so you can't really tell if you have the draw bar over the wax motor and coupled. I need the schematic and or test sequence for the E


Please confirm if this is the model you have.\015\012\015\012I might have some access to th ... Dishwashers

The Intake/ Drain light is on. It appears that the machine is not draining and that possibly the pump is not working properly. The drain line appears to be clear though I haven't pulled out the unit to check the drain line at the machine. Any suggestions?


... Miele Touchtronic G832SC Built-in Dishwasher

Blockage (i think) top draw - seal orginally locking draw


After you remove the rack you can also remove the large stainless cover( it unscrews, and then under that id the rotor assy , it also unscrews, giving you access to the ports that would be blocked if any, you can refer to your manual for ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Neff dishwasher doesn't seem to draw in enough water.have cleaned.knocks off after 30 secs


If you don't think it's filling with enough water, it is most likely the water valve. ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0723 seconds