Having problems with your Honda 2500 PSI Gas Pressure Washer ?

Washer stalls out when I pull the trigger on the hose.


Answers :

Repair Help & Product Troubleshooting for Honda 2500 PSI Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Washer stalls out when I pull the trigger on the hose.


... Honda 2500 PSI Gas Pressure Washer

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

PWER WASHER RUNS PERFECT, WHEN WATER COMES ON, IT STALLS. BUT IF YOU PULL TRIGGER BACK ON WAND, THEN SPRAYER WORKS. THE MINUTE YOU LET GO OF TRIGGER, IT STALLS OUT.


Hi you have got a fault with the unloader it's not unloading so its going a bove the 13amps and knocking the thermol overload out or blowing a fuse you could cable tie the trigger open or get a new unloader kit costing about £70.00 regards ... RTO 1800 PSI Pressure Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a


If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Troy bilt 2600psi 2.3gpm model 160 pressure washer, I hooked everything up like normal, It cranked up fine, when I pulled the trigger on the gun it stalled. When I try to crank it back up the cord wont even pull like its stuck any suggestions would really help me tks..


This sounds like the pump has dead headed. I.e. the unloader valve is sticking. Unhooking all of the hoses should eventually allow everything to free up. Once it is free what you should do is add about 3 ounces of oil into the water inlet connecti ... Pressure Washers

Pressure washer stalls when i pull the trigger


... Honda Pressure Washer PSI 3000

Pressure Washer Purchased in 2001. Used about 30 hours. It is very hard to start if at all. Good gas, good spark plug. Sometimes it will start within 50-100 pulls. After getting started, if you release hose trigger it will cut off. Any suggestions of what else to do? Thanks in advance.


I would look into getting the carb rebuilt, sounds like there is some gummed up valves. ... Pressure Washers

The pressure washer is cutting off when i pull the trigger to wash. The honda engine seems fine. it just stalls when i try to pressure wash.


... Pressure Washers

Engine idles down and sometimes stalls on pressure washer when trigger on wand is pulled


Clean out the carb fuel turns to **** after about 30 day for small engines ... Briggs & Stratton Pressure Washers

Pump Issue I have a john deere pressure washer. I hook the hose up to it, rurn the water on and no water comes out of the wand. I started the engine briefly and pulled the trigger on the wand and still nothing. The model number of the pump is Annovi Reverberi SJV 2.5G24-1. I can't seem to find any info on the G24? There is info on the G27-1. Not sure what to do here? Please help.


... Pressure Washers

Powerwasher hose to gun keeps blowing off when i pull the trigger of gun. the connection at the washer


Somewhere on the nozzle there is a lock. You must properly seat and lock the nozzle. Otherwise, guess what happens.\015\012\015\012If you have done all this, I must surmise the lock is broken or has dirt in it.\015\012\015\0 ... Karcher K2.26 Electric Power Washer

No pressure I have a husky 1750, With all connections clear of any obstructions the pressure washer turns on sounds normal, but when you pull the trigger there is no way near enough pressure to do anything..The gun and H/p hose is brand new..Any ideas?


It is probably air locked....Here's what you need to do. Connect the garden hose, and HP hose, but not the gun. Turn on the water, and let it run while you make sure that there are no high points in the garden hose that can trap air....Work the hos ... Pressure Washers

Engine stalls when you pull trigger on wand - Karcher 2500 PSI Pressure Washer


... Karcher 2500 PSI Pressure Washer

Pressure washer sputters and stalls when trigger is engaged


Hi k2times01It is a always a good idea to clean out the gas tank and use new fuel, however, this sounds like an RPM problem. Try adjusting the RPM up a tad and see if it runs better when you load it. If the RPM isn't the problem, you may have ... Pressure Washers

It will not take the chemical/soap in the pressure washer? I have checked both ends on the chemical hose and both seemed to fit tight on recievers. Then I checked and did not see where it was pulling air in the hose to keep it from pulling from chemical bottle. This is a brand new washer. Am I doing something wrong?


... Pressure Washers

Builds up to much pressure in hose and stalls engine


Sounds like the unloader is not working. try replacing it and see if that helps. ... Campbell Hausfeld PW2102 Gas Pressure Washer

MSV3024 pressure washer backfired after 2 hours of continuous use, then died. i was able to restart it but pulling the trigger kills the engine. i was able to pull the trigger rapidly and keep it running but holding the trigger down killed it again. now it won't restart. can it overheat? it has a full tank of gas.


... Simpson Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t


I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer

I have a craftsman 4.5hp quantum xte pressure washer 1800psi/4.5hp/2.0gpm mod 580.761800. I have to start the washer before I turn the water on and just today started with if I let go of the trigger on the wand the washer stalls. Can you advise as to what the problem is and how to solve? Thanks ****


The pressure relief valve(bypass) is most likely stuck or clogged. take the relief valve off and check for broken or jammed parts..there should be a bypass hose that goes around the pressure valve ... Briggs & Stratton Pressure Washers

No water I have a sears pressure washer. I hooked up the garden hose and pulled the triger with the engine off. No water. I disconnected the spray gun hose, were it connects to the pump.Turned on the hose,no water.Could the pump be cloged?


... Pressure Washers

Kodiak 4000 Bear, Washer runs smoothly, press trigger and washer begins pulsating jets of water, good pressure, used air hose on washer water line and wand, problem still exists. wash application


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0990 seconds