Having problems with your Honda Black Max 2600 PSI Pressure Washer ?

I need to replace the part of the pump where the siphon tube connects. Where can I find the part?


Answers :

This is for the chemical injector I would try to get it brazzed back on there isn't a lot of pressure on this fitting And honda olny makes the engine and then depending what kind of pump is on it but likely they olny make the pump So unless you have a part # your olny other recorse is black max and there not realy a top of the industry supplyer of power washers iv'e never deult with the company but i owen and repair this type of equipitment for a business So if you still have the peice that broke off try to fix it i think it will be your best soluition good luck
Is it actually a Honda pressure washer or does it just have a Honda motor on it? Try this place fisrt for parts. jackssmallengines.com
Repair Help & Product Troubleshooting for Honda Black Max 2600 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to replace the part of the pump where the siphon tube connects. Where can I find the part?


This is for the chemical injector I would try to get it brazzed back on there isn't a lot of pressure on this fitting And honda olny makes the engine and then depending what kind of pump is on it but likely they olny make the pump So unless you have ... Honda Black Max 2600 PSI Pressure Washer

I have a KitchenAid but model # KUDI24SEWH1. Can not find it on your list although another model without the last letters 'WH1' is on it. Anyway, my nephew ordered the parts he said needed to be replaced. One was the top water feed tube and bearing which he had no problem replacing when the part came in. But, he is having a very difficult time opening up the front door to replace the soap dispenser. Removed the 6 screw (three on each side) and the two at the top of the door but that is as far


You don't Use the WH2 just the first 6 letters and numbers.\015\012Jim ... KitchenAid KUDI24SE Built-in Dishwasher

My DPD 3100 is leaking from a brass fitting on the side of the pump (opposite of the white ??reset?? button. The brass fitting has a star shaped whole in the center. When i remove the fitting, there's a heavy duty spring behind it. Do i need to replace the fitting, or is there another problem? Where do i find parts for this?


First things first, before replacing I would wrap this valve with teflon tape and then retighten and see if the leak stops, I checked the entire schematic and found no listing for a spring so this is part of a valve assembly of some type. It might b ... Dewalt DPD3100 Gas Pressure Washer

How do i replace a squeeze tube on the pump for a Hobart LT1 ML104239. and where can i get the parts needed


... Hobart Dishwashers

I need to replace the heating element and electronic control board on my Kitchenaid KUDS01DL Dishwasher. I have the parts. I have been able to find directions on how to replace the heating element, but am not finding anything on the electronic control board. I don't even know where this part goes. I am guessing somewhere in the door, but can't find any instructions. Help...


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

I have a Kenmore Ultra Wash Dishwasher model 665.16379301. The spinner from the top of the dishwasher has come off. I have a replacement part but need to know what is required to replace it. Do I need to remove the feed tube assembly in order to replace it?


... Kenmore Dishwashers

Need new detergent cup dispenser for Model KUDI220T4. The detergent cup dispenser (Part number AP3042989) has been discontinued. Need to find the replacement part and directions on how to remove existing detergent cup dispenser and install new detergent cup dispenser.


... Kitchen and Much More Dishwashers

The door flops open as the rope has broken. I have the replacement part but need a diagram to show how to replace the part. Where can i find the diagram?


Documented in the manual...The plastic part goes on the metal hinge on the door...follow the rope down to the top wheel (clockwise and around) to the bottom wheel (counterclockwise and around), attach to the spring. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Magic Chef DU55CA-01 unit runs but when pump kicks on for discharge cyle water leaks on the floor from the what appears to be the solenoid part. The leaking stops as soon as the pump turns off. What part needs to be replaced? The unit was in storage for some time would this just be an issue with it sitting for some time? What is the best way to determine the real cause of the leak?


Leaking from drain valve shaft seal. If you just replace the seal it may still leak. Replacing the pump is a lot of work and not really worth it to cure a small leak. ... Magic Chef 24 in. DU6550 Built-in Dishwasher

Repair manual Water Pump seal is leaking bad and needs to be replaced. I don't have a manual of this part so that I can order the parts I need.


... Blakeslee D-8 Dishwasher

My KUDD01DPPA KITCHEN AID DISHWASHER BOTH TOP AND BOTTOM DRAWERS have red lights on in the front and the pumps keep pumping . Is there a flood switch that needs replacing? im a plumber by trade. So im very capable of replacing any of the parts.


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I need the part that the water hose connect to and then that part connect to pressure pump for a blue max 2200psi 1.6 gpm i thank it is a ck valve can you help me find that part thank you edward


Take the old one to a hardware store or homedepot and get a brass replacement ... Psi Blue Max 2200 High Pressure Gas Power Washer

Hi, I am looking to find replacement parts for the top rack glider wheel and screw on the right side of my dishwasher. Model # mdbh970awq. I have found parts break down web sites but none seem to have the part I need. Thanks for the help.


... Maytag 24 in. MDBH970AW Built-in Dishwasher

Bosch Dishwasher has started acting upo. If I turn on the dishwasher it runs the pump for approx 2 seconds then cuts out. This carries on the cycle spraying the soapy suds around the compartment but there is no running pump sound. Any idea how I can access the pump to either attempt to clean it out or to replace it? Or does this indicate another fault that may need attention. Any idea of the cost of parts UK. Thanks for assistance ****


Most dishwashers pump out briefly before filling in order to clear pressure chamber. The next step is the water fill which is monitored by the pressure/level switch. Once water level is attained timer will advance through cold rinse cycle. If no fill ... Dishwashers

Need to replace pressure line from the pump to the heater-need a part


... North Star Pressure Washers

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

Have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

I have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

I need the upper and lower rack rollers replaced but do not know the part numbers. I am looking for a parts diagram on the internet but have been unable to find one. GE Nautilus, Model GSD2200G00CC


This link, provided by www.repairclinic.com shows what you need.\015\012\015\012 ... GE Nautilus 24" Built-in Dishwasher

Dishwasher overflows I have a Maytag PDB3600AWX dishwasher. The pump works well, pumps all water out of the tub when reaching the appropriate cycle state. However, it keeps taking in water when it's not running / turned on (e.g., overnight) and the tub starts overflowing, cuasing obvious leakages (to the basement). What part needs to be replaced? Thanks, C Artz


Sounds like you've got a problem with the water intake valve(s). If it takes on water without water running in the sink, that is where I would look. If it happens when you use the sink, then I would also check your drain hose placement ... Dishwashers

We need to replace pump on dishwasher - Model PLDB998CC0 Part#5304463777 wE BOUGHT THE PART, BUT DO NOT KNOW HOW TO INSTALL. CAN YOU HELP?


Which pump is it drain or circulation pump. \015\012also just a thought now that you have saved some money on getting the part yourself,maybe you can call 10 repairmen and tell them how much to install only the pump.which ever has the lowest pr ... Dishwashers

I need to replace the lifter in my dishwasher. I have the new part, but darned if I can figure out how it's attached to the pumphousing. I just need a diagram to show it connects to the drain valve lever and then to the pump housing. Maytag PDB2430AWE.


... Dishwashers

Our whirlpool estate diswasher will not drain the water after a wash cycle. I have removed internal parts down to the drain and cleared the path. Moreover, I have removed the drain tube and clean it. Still water will not drain. I assume it is the pump. Can the pump motor be easily replaced? Thank you, Jim


You hve to find the right pump first ... Whirlpool Dishwashers

Broken fitting The plastic curved piece that attaches the hose to the white fitting on the back of the dishwasher broke, and I need a replacement.  I have been to Home Depot and they don't have anything to fit it, and I was told to go back to the manufacturer for a replacement piece but have looked online and can't find anything that would allow me to order the part.  Help!??


You don't have to change that piece,just tie the hose (drain hose ) to something that is equal height,this prevents siphoning. Please Rate This ! ... Danby 22 in. DDW396 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1367 seconds