Having problems with your Honda Karcher G2400HH-R Pressure Washer ?

Need help getting to an cleaning stuck unloader valve on a Karcher G 2400 HH Pressure washer. Thanks


Answers :

The cart body makes this process a little confining but it can be carried out without removing the pump from the motor.
\015\012
\015\012Diagram courtesy of: pressureparts.gif
\015\012
\015\012
\015\0127fb3f7d.png\015\012
    \015\012
  1. Refer to assembly 9 in the diagram. Remove the splash cup by working the push-on nut off the top of the cup.
  2. \015\012
  3. Remove two Torx fasteners (13) and twist the nylon valve retainer gently while pulling up to remove it. Be aware of the small parts under the retainer.
  4. \015\012
  5. The objective is to get the valve (12) out of the bore (A). Connect the hose and wand to the pump, make sure the wand valve is closed. Connect the water supply to the pump and turn on the water flow.
  6. \015\012
  7. Place a shop towel over the valve bore and with the throttle in the off position, pull the start cord briskly several times to see if enough pressure builds to pop the valve out of the bore. If not, set the throttle to low and start the engine. Unless the valve bore is really corroded, this should pop the valve out.
  8. \015\012
  9. If this process fails, you may have to unmount the pump and employ a more brutal approach that will likely require a new valve.
\015\012I have worked on my washer for the last 2-3 years to keep it going but I've opted to replace the pump this year. My replacement is an "AR RMV2G25D" (~$170) .
Repair Help & Product Troubleshooting for Honda Karcher G2400HH-R Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need help getting to an cleaning stuck unloader valve on a Karcher G 2400 HH Pressure washer. Thanks


The cart body makes this process a little confining but it can be carried out without removing the pump from the motor.\015\012\015\012Diagram courtesy of: ... Honda Karcher G2400HH-R Pressure Washer

Clean and unloader valve on Karcher hd3500 pressure washer -intermittent pressure on and off. Cleaned inlet screen. Think unloader valve is is under pressure knob? Will cleaning help?


Hi:Cleaning it is not enough. You need to make sure the o-rings are in good shape and grease it with a very very good waterproof grease. ... Karcher Pressure Washers

Karcher K3.91, lost some pressure and pulsing when trigger is release. stripped it down and checked all six valves and there all sealing as they should. i took apart the unloader valve cleaned and inspected and thats fine. there is NO water leeks anywhere or oil. preasure washer is 2 years old and gets used once a week for ten minutes. i really dont understand why its playing up


... Pressure Washers

I need to check the unloader valve on my Karcher 3000psi pressure washer. I was directed to your site for help. I just need to know what to unbolt to get to the valve.


... Pressure Washers

My Karcher 4000 SHR Pressure Washer pressure pulses when operating. I have checked with Karcher Technical Support and all their trouble shooting procedures except checking the unloading valve. Where is this valve, how do I get to it and how do I lubricate it?


It sounds like your unloading valve is crudded up with mineral deposits and stuck in a partway open state. look for a plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the ... Honda Karcher G4000RH Pressure Washer

Poor pressure karcher g 2500 pressure washer with a 5.5 honda engine. No high pressure, hose pulsates as does water out of the outlet. have removed the unloader valve twice and cleaned it to no avail


I had this same problem on my pressure washer.the pump had some broken parts in it .i found my replacement pump on EBay. ... Karcher 2500 PSI Pressure Washer

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

I have a Karcher HD 3101 pressure washer. The out pressure is not working. Is there a unloader valve that needs to be cleaned?


Yes, the unloader needs to be lubed. Send me a email at [email protected] with a discription of what you just listed and I will send you a pdf file on how to repair it. ... Karcher G3025OH Pressure Washer

Northstar Hot Water Pressure Washer (model #157322) While using the pressure washer the safety relief valve activated venting steam and hot water from it... I immediately shut it down and let it cool down. After it was cool, I turned on the water supply again and the relief valve was still spewing water from it. My neighbor said it was probably the "unloader" valve was stuck or damaged. I called around my area and it seems as though no one services my pressure washer.. Is there a manu


... Pressure Washers

I have a Karcher HD3500 and was told Imay have a stuck unloader valve. Where is it and is there a diagram showing how to get to and clean?


HiThe unloader valveis HERE If you go to D-2 it is part numbers 8 to 13. If it is stuck it is not only important to free i ... Honda Karcher G2400HH-R Pressure Washer

How do you locate/clean an unloader valve on a Karcher HD3000 pressure washer


... Karcher G3025OH Pressure Washer

Karcher pressure washer unloader valve sticking? I have the pump shown on page 3 of Karcher manual number 91392030. I removed the unloader valve, but am not sure if I have the entire assembly. I got the top seal and a spring. The bottom seal may be jammed in the pump.


... Karcher G3025OH Pressure Washer

I have a pressure washer with a faip 3 piston pump. the other day i was using it and it stopped unloading. i cleaned the unloader and it didn't help. I bought a new one and it still won't work. I e-mailed Ryobi and they will not respond. There were no instructions on installing and adjusting the unloader. Could you give me an idea how to install and set up the new unloader. Any help would be most appreciated.


I think your main problem is that the unloader valve needs to be lubricated. Use the very best water resistant bearing grease you can find. If you can e-mail me a pic of your unloader assembly I can try to explain how to set it up. [email protected] ... Honda Pressure Washers

Deville Excel Model # EXHA2425 Pressure washer. Is "unloader" the same as "bypass valve"? I have a deville excel Model # EXHA2425 pressure washer with a 5.0 Honda enginr. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get p


... Pressure Washers

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

Karcher G3050OH Pressure Washer Spill / Unloader Valve (Bypass)


You should put 'locktite' on the male thread and screw it in all the way and lock it there. That is how it works ,the spring keeps the valve at the bottom closed during high pressure operation. When the gun is released the part with the o-ring is for ... Karcher 2500 PSI Pressure Washer

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

How do I clean the unloader valve on a Karchner model G2600VH Cannot get steady pressure from the outlet of the nozzel have clean filter checked for leaks and replaced all nozzels still having issue with flux in pressure.


Check the tips and Videos at http://www.ereplacementparts.com/karcher-2600-11944040-pressure-washer-parts-c-33388_33389_34001.html ... Karcher 2500 PSI Pressure Washer

I have same problem with Chicago Electric # 47761 electric pressure washer as Aug 10 2010 writer had w/ Karcher 2500. Runs briefly then stops. Pressure is trapped in hose. I cleaned hose disassembled & greased valve in handle. No improvement. Problem appears to be premature wear of trigger cam in handle - both are plastic. Valve body is rigid nylon. Any thoughts??


... Pressure Washers

Unloader Valve - Karcher Pressure Washer


Where is the unloader valve locaed on a Briggs Stratton pressure washer? ... Honda Karcher G4000RH Pressure Washer

Karcher k2400hh pressure washer, water pressure cuts out.


Hello cikanek:\015\012\015\012Try this:\015\012\015\012From your posting, I assume you have removed the splash cap and the nylon bypass valve cover. Connect the water supply to the pump and connect the high pressure hose and w ... Honda Karcher G2400HH-R Pressure Washer

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

I can't get the igniter to start on north start pressure washer #157224. Fuses ok, indicator light in heat switch does not illuminate. Blower works, fuel dripping out. Cleaned fuel tank and pump and filter too! Tried jumpering past the thermostat didn't help either. Also, swapped pump and heat switches on main panel. No help!


... Pressure Washers

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

Pressure Washer will not reach high Pressure....how do i clean the unloader valve


Nozzle is clogged. Clean out with small diameter wire. ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2023 seconds